131. Structural health monitoring for performance assessment of bridges under flooding and seismic actionsLuke J. Prendergast, Maria P. Limongelli, Naida Ademovic, Andrej Anžlin, Gavin Kenneth, Mariano Zanini, 2018, izvirni znanstveni članek Povzetek: Bridges can be subjected to damaging environmental actions due to flooding and seismic hazards. Flood actions that result in scour are a leading cause of bridge failure, while seismic actions that induce lateral forces may lead to high ductility demand that exceeds pier capacity. When combined, seismic actions and scour can lead to effects that depend on the governing scour condition affecting a bridge. Loss of stiffness under scour can reduce the ductility capacity of a bridge but can also lead to an increase in flexibility that may reduce seismic inertial forces. Conversely, increased flexibility can lead to deck collapse due to support loss, so there exists some uncertainty about the combined effect of both phenomena. A necessary step towards the performance assessment of bridges under flooding and seismic actions is to calibrate numerical models that can reproduce structural responses under different actions. A further step is verifying the achievement of performance goals defined by codes. Structural health monitoring (SHM) techniques allow the computation of performance parameters that are useful for calibrating numerical models and performing direct checks of performance goal compliance. In this paper, various strategies employed to monitor bridge health against scour and seismic actions are discussed, with a particular focus on vibration-based damage identification methods.
Ključne besede: scour, seismic, damage, hazard, vibration-based methods
Objavljeno v DiRROS: 29.11.2023; Ogledov: 221; Prenosov: 118
 Celotno besedilo (2,18 MB)
Gradivo ima več datotek! Več... |
132. Condition assessment of roadway bridges: from performance parameters to performance goalsMaria P. Limongelli, Eleni Chatzi, Andrej Anžlin, 2018, izvirni znanstveni članek Povzetek: Deterioration of bridges due to ageing and higher demands, induced by increased traffic load, require the development of effective maintenance policies and intervention strategies. Such concern should be aimed at ensuring the required levels of safety, while optimally managing the limited economic resources. This approach requires a transversal advance; from the element level, through the system level, all the way to the network level. At the same time intervention prioritisation based on the importance of the system (bridge) inside the network (e.g. highway), or of the single structural element inside the bridge is dependent. The first step in bridge condition assessment is the verification of safety and reliability requirements that is carried out using the traditional prescriptive (deterministic) approach or the current performance-based (probabilistic) approach. A critical issue for efficient management of infrastructures lies in the available knowledge on condition and performance of bridge asset. This information is obtained using a collection of significant Performance Parameters at one or more of the three levels (element, system, and network). Traditional techniques for estimation of Performance Parameters rely on already established visual inspection. However, a more reliable description of the system performance is obtained through Non-Destructive Testing and Structural Health Monitoring. Condition assessment essentially pertains to the check of compliance with Performance Goals and requires the definition and computation of Performance Indicators. They are calculated directly from Performance Parameters or from physical models calibrated using the Performance Parameters collected on the structure. Paper overviews the steps to bridge condition assessment regarding safety and reliability.
Ključne besede: bridge, reliability, safety, condition assessment, performance goals, performance parameters
Objavljeno v DiRROS: 29.11.2023; Ogledov: 238; Prenosov: 119
Celotno besedilo (487,92 KB)
Gradivo ima več datotek! Več... |
133. Cost-benefit analysis of fire protection in buildings : application of a present net value approachThomas Gernay, Shuna Ni, David Unobe, Andrea Lucherini, Ranjit Kumar Chaudhary, Ruben Van Coile, 2023, izvirni znanstveni članek Povzetek: In fire safety engineering, cost–benefit analysis provides a systematic method to assess whether the projected benefits from a fire safety measure outweigh its costs. However, there remains a wide discrepancy between methods used in the field for cost–benefit analysis, as well as a lack of quantitative data on the costs and economic impact of fire protection in buildings. In a recent research project, a reference methodology was proposed based on Present Net Value evaluation and on a combination of specialized construction database, fire statistics, and numerical modeling for estimation of the cost components. This paper presents the application of the methodology to four case studies. The case studies allow describing the methodology, the collection of data, fire statistics, and loss estimation, as well as illustrating how the methodology can support decision-making when multiple alternatives are compared. Under the assumptions adopted for the single-family house and the residential timber building case studies, it is found that for every 1\$, invested in sprinklers, \$1.06 is saved. This benefit–cost ratio increases with increasing valuation of indirect losses and statistical value of life. Sensitivity analyses are provided to explore the robustness of the investment recommendations. The results of evaluations, adapted from the presented case studies with project-specific inputs, can support decision making for policy makers, insurance companies, and individual building owners.
Ključne besede: fire safety, cost-benefit analysis, fire protection, fire statistics, sprinklers, compartmentation
Objavljeno v DiRROS: 29.11.2023; Ogledov: 281; Prenosov: 42
Celotno besedilo (758,66 KB)
Gradivo ima več datotek! Več... |
134. |
135. In situ consideration of resistance of bridge girder according to EC2 with AEMAna Brunčič, Andrej Štrukelj, Maja Kreslin, Andrej Anžlin, Aljoša Šajna, 2023, objavljeni znanstveni prispevek na konferenci Povzetek: The paper presents a case study of a considerably cracked and degraded bridge in Slovenia: with the implementation of in-situ measurements under bending and shear and the use of a non-destructive acoustic emission technique. Despite the existing crack system, the latter was able to detect microstructural changes. These were characterised by low values of average frequency (AF), as well as lower values of the rise time-amplitude ratio (RA), and energy. A correlation between shear capacity and acoustic activity was observed. This promises to expand the use of AE in the process of assessing of the load-bearing capacity of existing concrete structures.
Ključne besede: shear resistance, shear crack, crack width, acoustic emission (AE) parameters, bridge girder, stiffness, elasticity, damage evaluation
Objavljeno v DiRROS: 28.11.2023; Ogledov: 237; Prenosov: 120
Celotno besedilo (1,08 MB)
Gradivo ima več datotek! Več... |
136. Pilot production of façade panels : variability of mix designMajda Pavlin, Barbara Horvat, Vilma Ducman, 2023, objavljeni znanstveni prispevek na konferenci Povzetek: As part of the WOOL2LOOP project, the Slovenian National Building and Civil Engineering Institute (ZAG), in collaboration with Termit d.d. were responsible for the production of façade panels. An initial mix design was developed at ZAG, where alkali-activated façade panels were produced, primarily from stone wool waste, while production took place at Termit. The mix design was changed twice during the pilot production, before a final product with suitable durability was developed. A compressive strength of up to 60 MPa and bending strength of approximately 20 MPa was achieved. The mechanical properties, however, varied, due to the unevenly milled batches of the milled mineral wool. Milling on a larger scale is very challenging, and it is difficult to obtain consistent quality of the milled material. Once the correct curing process had been found, however, the panels produced showed good performance. Moreover, the results from leaching tests showed that the elevated concentrations of certain elements (Cr, As and Mo) did not exceed the legal limits for non- hazardous waste.
Ključne besede: waste mineral wool, alkali activated material, façade panels, pilot production, circular economy
Objavljeno v DiRROS: 28.11.2023; Ogledov: 296; Prenosov: 112
Celotno besedilo (1000,34 KB)
Gradivo ima več datotek! Več... |
137. Microwave irradiation of alkali - activated metakaolin slurryBarbara Horvat, Branka Mušič, Majda Pavlin, Vilma Ducman, 2023, objavljeni znanstveni prispevek na konferenci Povzetek: The building and civil engineering industry generates more than 40% of man-caused carbon emissions, consumes a lot of energy just to produce building materials, generates a large amount of waste through construction and demolition, and consumes a large amount of natural resources. One of the possible solutions is to use alkali-activated materials, which can use waste instead of raw materials and are produced at lower temperatures, with less energy consumption and in less time than traditional building products. All of this lowers the carbon footprint, which could be further reduced by the timely-short implementation of microwave irradiation in the early stages of alkali-activation synthesis. Therefore, metakaolin activated with Na-water glass in a theoretically optimal ratio was irradiated with microwaves of 2.45 GHz at powers of 100 W and 1000 W for 1 min, and compared to non-irradiated reference cured only at room conditions. Samples prepared at higher power, i.e., 1000 W, solidified completely and foamed. TG-DTA was performed on all samples in the early stages of curing, mechanical strengths were measured on 3 and 28-day- old samples, and leaching tests on aged samples.
Ključne besede: metakaolin, alkali activated material, alkali activated foams, microwave irradiation
Objavljeno v DiRROS: 28.11.2023; Ogledov: 274; Prenosov: 112
Celotno besedilo (791,17 KB)
Gradivo ima več datotek! Več... |
138. Toksikološka analiza vsebine vojaških čutar, zakopanih 70 let v kraški jami na Kočevskem, JV SlovenijaJanez Mulec, Sara Skok, Vesna Zalar Serjun, Andrej Mihevc, 2019, izvirni znanstveni članek Povzetek: Za odkrivanje ostankov materialnih sledi se na dobro ohranjenih predmetih lahko opravijo forenzične preiskave. V Breznu v Debliških livadah je bilo odkritih večje število predmetov, ki so bili odvrženi v jamo v maju in juniju 1945. Med odkritim materialom so bile tudi vojaške čutare. Nekatere izmed čutar so še vsebovale tekočino, nekatere pa tudi poltrdo, gelasto oborino. Tekočina in oborina iz čutar sta vsebovali kovine, ki so se najverjetneje s časom izlužile iz kovinske posode. Korozija čutar nakazuje prisotnost minerala hematita. Vsebina čutar je nadalje vsebovala nekaj raztopljene organske snovi (celotni organski ogljik – TOC v tekočini 9,22 mg/l, v tekočini ekstrahirane oborine 34,1 mg/l), nekaj mikrobne biomase ter relativno visoke koncentracije nitrata (240 mg/l v tekočini, 55 mg/l v ekstrahirani oborini) in sulfata (18mg/l v tekočini, 836 mg/l v ekstrahirani oborini). Bakterijskih indikatorjev, Escherichia coli in enterokokov, ki bi kazali na fekalno kontaminacijo vsebine, v vzorcih nismo zaznali. Raztopina in oborina sta izkazovali podobno stopnjo toksičnosti, okrog 20%inhibicijo bioluminiscence bakterije Vibrio fischeri. Glede na Pravilnik o pitni vodi tekočina s sedanjimi kemijskimi lastnostmi ni primerna za uživanje. Rezultati ne kažejo nujno na toksičnost izvornih tekočin iz časa, ko so bile čutare odvržene v jamo, ampak bi se toksičnost lahko razvila postopoma zaradi izluževanja kovin iz posode, zlasti aluminija, in (bio)kemijskih reakcij. Navkljub stabilnim jamskim razmeram, ki so jim bile izpostavljene čutare, ugotovljeni parametri ne podpirajo dolgoročne ohranitve stabilne DNA za morebitne nadaljnje forenzične analize.
Ključne besede: jame, vojaški material, toksičnost
Objavljeno v DiRROS: 23.11.2023; Ogledov: 247; Prenosov: 136
Celotno besedilo (912,75 KB)
Gradivo ima več datotek! Več... |
139. Elucidating nucleation stages of transgranular stress corrosion cracking in austenitic stainless steel by in situ electrochemical and optical methodsSarmiento Klapper Helmuth, Bojan Zajec, Andreas Heyn, Andraž Legat, 2019, izvirni znanstveni članek Povzetek: The pitting and environmentally assisted cracking resistance of austenitic stainless steels (SS) is challenged in several industrial applications particularly those involving hot chloride-concentrated streams. Directional drilling used in the oil and gas exploration is one of these applications. Indeed, high strength CrMn-SS commonly used in drilling technology have a high tendency to fail by stress corrosion cracking (SCC) preceded by localized corrosion once subjected to highly chloride-concentrated drilling fluids at elevated temperatures. A comprehensive understanding regarding the mechanisms governing the transition from pitting into SCCis not currently available, though. Therefore, mechanistic aspects such as the effect of loading conditions on pit nucleation and repassivation as well as the synergistic effect between pit stabilization and the nucleation of a stress corrosion crack are of great practical significance. To investigate this an electrochemical-, optical- and mechanical- monitored SCC test was conducted on a CrMn-SS in an alkaline brine at elevated temperature. The transition from metastable to stable pitting and subsequently to SCC in this system was documented in-situ for the first time. Results supported H.S. Isaacs postulates regarding the interpretation of electrochemical signals and demonstrated that loading conditions affect pit nucleation and repassivation leading to a higher susceptibility of the material to pitting, which preceded SCC.
Ključne besede: pitting corrosion, stress corrosion cracking, monitoring, elektrochemical noise, austenitic stainless steel
Objavljeno v DiRROS: 23.11.2023; Ogledov: 250; Prenosov: 192
Celotno besedilo (2,28 MB)
Gradivo ima več datotek! Več... |
140. Hydrothermal synthesis of rare-earth modified titania : influence on phase composition, optical properties, and photocatalytic activityNejc Rozman, David Maria Tobaldi, Uroš Cvelbar, Harinarayanan Puliyalil, Joao Antonio Labrincha, Andraž Legat, Andrijana Sever Škapin, 2019, izvirni znanstveni članek Povzetek: In order to expand the use of titania indoor as well as to increase its overall performance, narrowing the band gap is one of the possibilities to achieve this. Modifying with rare earths (REs) has been relatively unexplored, especially the modification of rutile with rare earth cations. The aim of this study was to find the influence of the modification of TiO2 with rare earths on its structural, optical, morphological, and photocatalytic properties. Titania was synthesized using TiOSO4 as the source of titanium via hydrothermal synthesis procedure at low temperature (200 °C) and modified with selected rare earth elements, namely, Ce, La, and Gd. Structural properties of samples were determined by X-ray powder diffraction (XRD), and the phase ratio was calculated using the Rietveld method. Optical properties were analyzed by ultraviolet and visible light (UV-Vis) spectroscopy. Field emission scanning electron microscope (FE-SEM) was used to determine the morphological properties of samples and to estimate the size of primary crystals. X-ray photoelectron spectroscopy (XPS) was used to determine the chemical bonding properties of samples. Photocatalytic activity of the prepared photocatalysts as well as the titania available on the market (P25) was measured in three different setups, assessing volatile organic compound (VOC) degradation, NOx abatement, and water purification. It was found out that modification with rare earth elements slows down the transformation of anatase and brookite to rutile. Whereas the unmodified sample was composed of only rutile, La- and Gd-modified samples contained anatase and rutile, and Ce-modified samples consisted of anatase, brookite, and rutile. Modification with rare earth metals has turned out to be detrimental to photocatalytic activity. In all cases, pure TiO2 outperformed the modified samples. Cerium-modified TiO2 was the least active sample, despite having a light absorption tail up to 585 nm wavelength. La- and Gd-modified samples did not show a significant shift in light absorption when compared to the pure TiO2 sample. The reason for the lower activity of modified samples was attributed to a greater Ti3+/Ti4+ ratio and a large amount of hydroxyl oxygen found in pure TiO2. All the modified samples had a smaller Ti3+/Ti4+ ratio and less hydroxyl oxygen
Ključne besede: TiO2, photocatalytic activity, rare earths, modification, visible light activity
Objavljeno v DiRROS: 22.11.2023; Ogledov: 297; Prenosov: 149
Celotno besedilo (2,40 MB)
Gradivo ima več datotek! Več... |
