Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Povzetek: Within the framework of the EUROfusion Consortium, the Characterization of armour, heat sinks materials and joints sub-project of the Work Package Material (WP-MAT) has been dedicated to the development of different tungsten (W) monoblock mock-ups equipped with advanced materials for divertor target applications in the EU-DEMO fusion reactor. Assessing the status of the relevant joining interfaces of these mock-ups, not only after fabrication but throughout the whole component lifetime, plays a key role in the qualification process. At the ENEA Special Technologies Laboratory (TES), a number of facilities have been built to perform non-destructive inspections of plasma-facing components for fusion applications by ultrasonic testing (UT). The present work reports on the results of the UT inspections assessing the structural integrity of the relevant joining interfaces of three small-scale mock-ups provided with advanced W armour materials, specifically W-matrix with W2C inclusions consolidated by Spark Plasma Sintering (SPS), K-doped rolled W and K-doped laminated W. The UT examinations are carried out after fabrication and after the high heat flux tests (HHFT) at the neutral beam facility GLADIS. All results confirm the high-quality joining achieved by HIP and HRP. During the HHF tests of mock-ups, after a few hundred HHFT cycles defects are detected at the joining interfaces, due to debonding, delamination and W material cracks mainly affecting the loaded zone. The ultrasonic pulse-echo technique provides not only the size and position of the defects in the plane orthogonal to the ultrasonic beam, but also their depth in the material. During the analysis, the probe is inserted inside the pipe and the mock-up is examined in a cylindrical configuration. The coupling medium (demineralized water) is poured only inside the pipe. The main inspection parameters and the piezoelectric probes are chosen to obtain the maximum resolution in accordance with the thickness and joining interfaces to be analyzed.
Ključne besede: DEMO, divertor, advanced tungsten, high heat flux test, non-destructive test, ultrasonic examination
Objavljeno v DiRROS: 03.09.2025; Ogledov: 604; Prenosov: 344
Celotno besedilo (775,68 KB)
Gradivo ima več datotek! Več...

Povzetek: Photovoltaic modules have been shown to influence how a fire propagates across a flat roof, but the circumstances for which building attached photovoltaic (BAPV) modules promote fire propagation on a sloped roof is not studied in detail. Therefore, a series of small-medium- and large-scale experiments on a sloped roof with a BROOF(t2)-rated bituminous roof membrane on a wood chipboard substrate has been performed. Steel plates mimicking non-combustible photovoltaic (PV) modules were placed at different distances above the roof. Different sized wood cribs placed in the gap between the roof and the PV module were used as the ignition source. Similarly to findings for flat roofs, the experiments showed that the gap distance and the size of the ignition source are key factors for how far the fire propagates from the starting point. This supports that BAPV installations affect the fire dynamics on roofs. As such, the complete system of roof composition and PV installation needs to be considered as a whole to ensure adequate fire safety levels.
Ključne besede: photovoltaic systems, fire propagation, roof safety, ignition source, heat flux
Objavljeno v DiRROS: 12.02.2025; Ogledov: 831; Prenosov: 461
Celotno besedilo (1,27 MB)
Gradivo ima več datotek! Več...

Povzetek: This research study concerns an experimental, budget-friendly, electricity- powered apparatus for bench-scale fire testing. The apparatus consists of various elements, of which the most important are ceramic heating pads, used to impose heat fluxes on exposed surfaces of specimens. The test method allows to control the heating pads’ temperature and to adjust the distance between the heating pads and the specimen to obtain well-defined heat fluxes up to 50–60 kW/m2. Higher heat fluxes and temperatures can be obtained by setting the heating pads in full power mode, with or without the use of a thermal shield, which can lead to heat fluxes up to 150 kW/m2. The heating and thermal boundary conditions imposed by the apparatus are characterised and discussed, and the thickness of the convective boundary layer at the heating pads’ surface is estimated significantly lower than in the case of gas- fired radiant panels. The performance of the apparatus is analysed for various conditions: controlling the temperature of the heating pads, in an open environment or with the presence of thermal shields, and in full power mode. A few examples of application of the apparatus to fire test typical construction materials (steel and glass) are also presented. These results emphasise the well-defined heating conditions in temperature-controlled mode. The study finally discusses the advantages and limitations of the apparatus, as well as many possibilities of future applications and improvement for future research studies.
Ključne besede: radiant panels, fire testing, heat transfer, heat flux, electrical heating pads, thermal boundary conditions
Objavljeno v DiRROS: 15.04.2024; Ogledov: 2113; Prenosov: 1404
Celotno besedilo (3,11 MB)
Gradivo ima več datotek! Več...