Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Povzetek: The investigation focused on the quasicrystalline aluminum alloy Al-Mn-Cu-Mg-Si-Ti. The influence of microstructure of aluminum alloy strengthened with quasicrystals on its corrosion resistance was studied. The properties of newly designed quasicrystalline aluminum alloy (QC) were compared to the properties of standard AlSi9Cu3 alloy (DIN 226). Both aluminum alloys (QC and AlSi9Cu3) were cast in a steel die with a controlled cooling rate. After the preparation of the samples, the microstructural characterization was carried out. In the quasicrystalline alloy, the microstructure was dominated by a primary phase with fivefold symmetry, representing the quasicrystalline phase. To investigate corrosion properties, open-circuit potential, linear polarization and potentiodynamic polarization measurements were performed. The influence of corrosion on mechanical properties was studied by conducting tensile tests on environmentally exposed alloys. It was concluded that the quasicrystalline alloy has comparable corrosion properties to the commercially widely used AlSi9Cu3 alloy. In the latter alloy, corrosion was observed to initiate in the vicinity of the Al2Cu intermetallic compound particles. In the case of the QC alloy, corrosion attacked mainly the αAl phase (matrix).
Ključne besede: quasicrystals, corrosion, aluminum alloys, microstructure, electrochemical measurements
Objavljeno v DiRROS: 14.07.2025; Ogledov: 653; Prenosov: 535
Celotno besedilo (2,96 MB)
Gradivo ima več datotek! Več...

Povzetek: A low carbon/ high chromium martensitic stainless steel, X17CrNi16-2, was heat treated using two different hardening and tempering regimes (1050 ◦ C/480 ◦ C or 980 ◦C/600 ◦C) — promoting either a high strength or high toughness state, respectively and further combined with deep cryogenic treatment (DCT) at 196 ◦C for 24 h. Over recent years DCT has been recognized as a promising technique to improve the properties of steel, predominantly with respect to its tensile strength, toughness and wear resistance. The influence of DCT on the hydrogen embrittlement resistance of martensitic stainless steel has not yet, however, been reported. A slow strain rate tensile test (SSRT) with simultaneous cathodic hydrogen charging was selected as the method to assess potential susceptibility to hydrogen embrittlement (HE). Relatively low-intensity hydrogen charging, utilizing a constant current density of 0.1 mA/cm2, in a non-corrosive, slightly alkaline buffer solution, led to a clear reduction in the ultimate tensile stress. This reduction, and therefore the HE susceptibility, was more pronounced in the steel with a higher strength (i.e. that subject to the 1050 ◦C/ 480 ◦C heat treatment condition). Furthermore, DCT did not appear to have any impact on the steel’s mechanical properties in the presence of hydrogen. Fractographic analysis showed clear evidence of HE in the hydrogen-charged specimens. This paper presents results of the SSRT tests and further fractography results, and discusses the impact of conventional and deep cryogenic treatment on HE susceptibility.
Ključne besede: martensitic stainless steel, deep cryogenic treatment, hydrogen embrittlement, slow strain rate tensile test
Objavljeno v DiRROS: 23.05.2024; Ogledov: 1359; Prenosov: 959
Celotno besedilo (17,73 MB)
Gradivo ima več datotek! Več...

Povzetek: CoCrMo and Ti6Al4V are widely used in medical, dental and 3D printing technology, allowing the accurate fabrication of geometrically complicated structures. In order to reduce the costs of printed objects, the reuse of powder is common daily practice. AQ1 When using 3D printing technology, the direct impact of elevated temperatures and the influence of the laser beam may change the properties of the powder when it is reused, thus affecting the final properties of the printed object. The main aim of the present study was to investigate the impact of reused powder on the mechanical, microstructural and electrochemical properties of 3D printed objects. 3D printed objects fabricated from virgin and reused powder of both alloys were analyzed by metallographic observation, computed tomography, XRD and electrochemical methods. The main finding of the study was that the use of reused powder (recycled 3 times) does not detrimentally affect the mechanical and corrosion integrity of 3D printed CoCr and Ti6Al4V alloys, especially for the purpose of applications in dentistry.
Ključne besede: additive manufacturing, selective laser melting, virgin powder, reused powder, microtomography
Objavljeno v DiRROS: 08.01.2024; Ogledov: 1978; Prenosov: 768
Celotno besedilo (2,93 MB)
Gradivo ima več datotek! Več...

Povzetek: The impact of the microstructural properties of a Ti6Al4V alloy on its electrochemical properties, as well as the effect of the α- and β-phases present within it, is still unclear. With the introduction of new, emerging technologies, such as selective laser melting and post heat treatments, the effect of the microstructure on an alloy's corrosion properties has become increasingly interesting from a scientific perspective. When these alloys are produced through different methods, despite an identical chemical composition they have diverse microstructures, and consequently display varying resistance to corrosion. In the present research study, Ti–6Al–4V alloy specimens produced by three different processes, leading to the formation of three different microstructures were investigated: heat treated specimen fabricated by selective laser melting, wrought and cast specimens. The impact of the microstructure of these alloys when immersed in artificial saliva was studied through the use of various electrochemical techniques, by microscopical examinations, and time-of-flight secondary ion mass spectrometry. Corrosion properties were investigated by the measurement of open circuit potential, linear polarization, and potentiodynamic curve measurements followed by microscopical examinations, and time-of-flight secondary ion mass spectrometry examination was conducted to reveal spatial distribution of alloying species on oxide film. It was found that the difference between specimens containing an α+β microstructure was small and not dependent on the aspect ratio of the β-phase, alloy grain size, and vanadium partitioning coefficient, but rather on the size, shape, and content of this phase.
Ključne besede: Ti6Al4V, dental alloy, microstructure, corrosion resistance, heat treatment, ToF-SIMS
Objavljeno v DiRROS: 26.10.2023; Ogledov: 2195; Prenosov: 1275
Celotno besedilo (8,12 MB)
Gradivo ima več datotek! Več...

Povzetek: The high temperature corrosion at 650°C in the presence of NaCl at atmospheric pressure of AISI 304L, AISI 309, AISI 310S, AISI 314 and AISI 321 austenitic stainless steel was studied. The specimens were cyclically heated in the furnace and immersed in a 3.5% aqueous NaCl solution after cooling for 15 min. After each cycle, the change in mass of the samples was measured. The corroded samples were analysed by SEM /EDX, and the corrosion products were analysed by XRD. The chloride ions react with the steel surface to form porous and poorly adherent oxides and metal chlorides. After the mass increase during the first exposure cycles, spalling of the oxides occurred. The high temperature austenitic stainless steels (AISI 309, AISI 310S, AISI 314) showed less mass loss than conventional austenitic steels (AISI 304L). Surprisingly, the stainless steel AISI 321 showed a similar low weight loss after the cyclic test as AISI 309, but a detailed analysis of the exposed surfaces after the test showed a similar corrosion attack as for AISI 304. After the cyclic test at high temperature in the presence of NaCl, a higher concentration of Cr and Ni definitely improves the corrosion resistance under the present conditions, but a certain addition of Si is even more obvious.
Ključne besede: austenitic stainless steel, high temperature corrosion, NaCl, exhaust systems, open access
Objavljeno v DiRROS: 31.05.2023; Ogledov: 1609; Prenosov: 925
Celotno besedilo (1,53 MB)
Gradivo ima več datotek! Več...