1991. Solidification behavior of Fe-6.5Si alloy powder for AM-SLM processing, as assessed by differential scanning calorimetryDarja Steiner Petrovič, Črtomir Donik, Irena Paulin, Matjaž Godec, Maja Vončina, Martin Petrun, 2023, izvirni znanstveni članek Ključne besede: soft magnetic alloy, differential scanning calorimetry, oxygen, high-temperature phase, microstructure, eutectics Objavljeno v DiRROS: 02.02.2024; Ogledov: 402; Prenosov: 180 Celotno besedilo (9,05 MB) Gradivo ima več datotek! Več... |
1992. Tribological evaluation of vegetable ▫$oil/MoS_2$▫ nanotube-based lubrication of laser-textured stainless steelMarjetka Conradi, Bojan Podgornik, Maja Remškar, Damjan Klobčar, Aleksandra Kocijan, 2023, izvirni znanstveni članek Povzetek: In the present work, the functionalisation of austenitic stainless steel, AISI 316L surfaces via nanosecond Nd:YAG laser texturing in order to modify the surface morphology with crosshatch and dimple patterns is presented. A tribological analysis under lubrication with sunflower and jojoba oil with and without the addition of a solid lubricant, MoS2 nanotubes, was performed. In conjunction with friction/wear response laser-textured surface wettability, oil spreadability and oil retention capacity were also analysed. It was shown that the crosshatch pattern generally exhibited lower friction than the dimple pattern, with the addition of MoS2 nanotubes not having any significant effect on the coefficient of friction under the investigated contact conditions. This was found in addition to the better oil spreadability and oil retention capacity results of the crosshatch-textured surface. Furthermore, texturing reduced the wear of the stainless-steel surfaces but led to an approximately one order of magnitude larger wear rate of the steel counter-body, primarily due to the presence of hard bulges around the textured patterns. Overall, the crosshatch pattern showed better oil retention capacity and lower friction in combination with different vegetable oils, thus making it a promising choice for improving tribological performance in various environmentally friendly applications. Ključne besede: tribology, stainless steel, vegetable oil lubrication, MoS2 nanotubes Objavljeno v DiRROS: 02.02.2024; Ogledov: 303; Prenosov: 161 Celotno besedilo (4,56 MB) Gradivo ima več datotek! Več... |
1993. Recovery study of gold nanoparticle markers from lateral flow immunoassaysTilen Švarc, Peter Majerič, Darja Feizpour, Žiga Jelen, Matej Zadravec, Timi Gomboc, Rebeka Rudolf, 2023, izvirni znanstveni članek Povzetek: Lateral flow immunoassays (LFIAs) are a simple diagnostic device used to detect targeted analytes. Wasted and unused rapid antigen lateral flow immunoassays represent mass waste that needs to be broken down and recycled into new material components. The aim of this study was to recover gold nanoparticles that are used as markers in lateral flow immunoassays. For this purpose, a dissolution process with aqua regia was utilised, where gold nanoparticles were released from the lateral flow immunoassay conjugate pads. The obtained solution was then concentrated further with gold chloride salt (HAuCl4) so that it could be used for the synthesis of new gold nanoparticles in the process of ultrasonic spray pyrolysis (USP). Various characterisation methods including scanning electron microscopy, transmission electron microscopy, ultraviolet-visible spectroscopy and optical emission spectrometry with inductively coupled plasma were used during this study. The results of this study showed that the recovery of gold nanoparticles from lateral flow immunoassays is possible, and the newly synthesised gold nanoparticles represent the possibility for incorporation into new products. Ključne besede: gold nanoparticles, recovery, LFIA, ultrasonic spray pyrolysis, characterisation Objavljeno v DiRROS: 02.02.2024; Ogledov: 403; Prenosov: 164 Celotno besedilo (6,25 MB) Gradivo ima več datotek! Več... |
1994. Approcci ecosistemici per l'adattamento ai cambiamenti climatici e la riduzione dei rischi: creare sinergie e promuovere il dialogo : conferenza2023, druge monografije in druga zaključena dela Povzetek: Lo scopo della conferenza di apertura del progetto ECO2SMART è promuovere gli approcci ecosistemici (EbA e Eco-DRR) per l’adattamento ai cambiamenti climatici e la riduzione del rischio di catastrofi. Intendiamo raggiungere questo obiettivo presentando buone pratiche di soluzioni sostenibili già implementate, condividendo conoscenze, creando connessioni e promuovendo il dialogo tra le parti interessate. Nel corso della conferenza verranno illustrate le opportunità offerte dal progetto ECO2SMART ed i principali risultati attesi alla fine di questo progetto. Objavljeno v DiRROS: 01.02.2024; Ogledov: 462; Prenosov: 265 Celotno besedilo (2,91 MB) Gradivo ima več datotek! Več... |
1995. Influence of oil viscosity on the tribological behavior of a laser-textured Ti6Al4V alloyMarjetka Conradi, Aleksandra Kocijan, Bojan Podgornik, 2023, izvirni znanstveni članek Povzetek: Laser texturing with a dimple pattern was applied to modify a Ti6Al4V alloy at the micro level, aiming to improve its friction and wear resistance in combination with oil lubrication to optimize the performance in demanding industrial environments. The tribological analysis was performed on four different dimple-textured surfaces with varying dimple size and dimple-to-dimple distance and under lubrication with three different oils, i.e., T9, VG46, and VG100, to reflect the oil viscosity’s influence on the friction/wear of the laser-textured Ti6Al4V alloy. The results show that the surfaces with the highest texture density showed the most significant COF reduction of around 10% in a low-viscosity oil (T9). However, in high-viscosity oils (VG46 and VG100), the influence of the laser texturing on the COF was less pronounced. A wear analysis revealed that the laser texturing intensified the abrasive wear, especially on surfaces with a higher texture density. For low-texturing-density surfaces, less wear was observed for low- and medium-viscosity oils (T9 and VG46). For medium-to-high-texturing densities, the high-viscosity oil (VG100) provided the best contact conditions and wear results. Overall, reduced wear, even below the non-texturing case, was observed for sample 50–200 in VG100 lubrication, indicating the combined effect of oil reservoirs and increased oil-film thickness within the dimples due to the high viscosity. Ključne besede: oil lubrication, surface modification, Ti-based alloy, tribology Objavljeno v DiRROS: 01.02.2024; Ogledov: 448; Prenosov: 175 Celotno besedilo (4,00 MB) Gradivo ima več datotek! Več... |
1996. The impact of Al2O3 particles from grit-blasted Ti6Al7Nb (alloy) implant surfaces on biocompatibility, aseptic loosening, and infectionBoštjan Kocjančič, Klemen Avsec, Barbara Šetina, Darja Feizpour, Matjaž Godec, Veronika Kralj-Iglič, Rok Podlipec, Andrej Cör, Mojca Debeljak, John T. Grant, Monika Jenko, Drago Dolinar, 2023, izvirni znanstveni članek Ključne besede: Ti6Al7Nb implant alloy cementless hip endoprostheses, roughness, Al2O3 grit blasting, surface and subsurface implant contamination, cytotoxicity, aseptic loosening, infection, osseointegration Objavljeno v DiRROS: 01.02.2024; Ogledov: 452; Prenosov: 203 Celotno besedilo (16,21 MB) Gradivo ima več datotek! Več... |
1997. Aspects of bending high-borated austenitic stainless steel sheets for interim storage of spent nuclear fuelJosef Odehnal, Tomáš Studecký, Petra Čejková, Ivana Poláková, Martin Rund, Václav Bruná, Petr Martinek, Pavel Francisko, Črtomir Donik, 2023, izvirni znanstveni članek Ključne besede: interim storage, spent fuel, borated stainless steel, cold working, bending Objavljeno v DiRROS: 01.02.2024; Ogledov: 336; Prenosov: 166 Celotno besedilo (10,05 MB) Gradivo ima več datotek! Več... |
1998. Influence of precipitation hardening on the mechanical properties of Co-Cr-Mo and Co-Cr-W-Mo dental alloysMarko Sedlaček, Katja Zupančič, Barbara Šetina, Borut Kosec, Matija Zorc, Aleš Nagode, 2023, izvirni znanstveni članek Ključne besede: Co-Cr alloys, microstructure analysis, hardness, wear resistance Objavljeno v DiRROS: 01.02.2024; Ogledov: 439; Prenosov: 237 Celotno besedilo (53,05 MB) Gradivo ima več datotek! Več... |
1999. Predicting the quality of grain refiners from electrical resistance measurements of aluminumMaja Vončina, Irena Paulin, Jože Medved, Mitja Petrič, 2023, izvirni znanstveni članek Ključne besede: Al-Ti-B grain-refiners, quality, TiB2 particles, Al3Ti particles, electrical resistance measurements Objavljeno v DiRROS: 01.02.2024; Ogledov: 381; Prenosov: 186 Celotno besedilo (8,93 MB) Gradivo ima več datotek! Več... |
2000. Effects of variated final temperature and workpiece thickness for hot rolling of aluminum alloy EN AW-8011Jakob Kraner, Peter Cvahte, Primož Šuštarič, Tomaž Šuštar, Črtomir Donik, Irena Paulin, Shae K. Kim, Kjung Il Kim, 2023, izvirni znanstveni članek Ključne besede: aluminum alloy, hot rolling, simulations, metallography, mechanical properties Objavljeno v DiRROS: 01.02.2024; Ogledov: 365; Prenosov: 191 Celotno besedilo (5,46 MB) Gradivo ima več datotek! Več... |