| Naslov: | Effect of Ti and S content on the properties and machinability of low-carbon ferritic–pearlitic steel |
|---|
| Avtorji: | ID Arh, Boštjan (Avtor)
ID Tehovnik, Franc (Avtor)
ID Vode, Franci (Avtor)
ID Podgornik, Bojan (Avtor) |
|---|
| Datoteke: |  PDF - Predstavitvena datoteka, prenos (12,95 MB)
MD5: 01C4871825692633D7B1051AD1C1CC77
 URL - Izvorni URL, za dostop obiščite https://www.mdpi.com/2075-4701/14/9/977
|
|---|
| Jezik: | Angleški jezik |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: |  IMT - Inštitut za kovinske materiale in tehnologije
|
|---|
| Povzetek: | This research was focused on the effect of Ti and S content on the formation of non-metallic inclusions and their influence on the mechanical properties and machinability of low-carbon ferritic– pearlitic steels. An analysis and classification of the non-metallic inclusions were carried out. The tensile strength and impact toughness were determined from samples taken in the rolling direction. Machinability investigations were carried out on a CNC turning machine and by analyzing the surface roughness. TiO-TiN inclusions are present in steels with an increased Ti content. In these steels, the hardness, tensile strength, and cutting forces increase with a higher proportion of Ti. In the second group of steels with increased contents of S, Al, and Ca, MnS and CaO-Al2O3-MnS non-metallic inclusions are formed. As the S content increases, the tensile strength and cutting forces decrease, while the impact toughness increases. In steels with added Ti, the This research was focused on the effect of Ti and S content on the formation of non-metallic inclusions and their influence on the mechanical properties and machinability of low-carbon ferritic– pearlitic steels. An analysis and classification of the non-metallic inclusions were carried out. The tensile strength and impact toughness were determined from samples taken in the rolling direction. Machinability investigations were carried out on a CNC turning machine and by analyzing the surface roughness. TiO-TiN inclusions are present in steels with an increased Ti content. In these steels, the hardness, tensile strength, and cutting forces increase with a higher proportion of Ti. In the second group of steels with increased contents of S, Al, and Ca, MnS and CaO-Al2O3-MnS non-metallic inclusions are formed. As the S content increases, the tensile strength and cutting forces decrease, while the impact toughness increases. In steels with added Ti, the machining is more difficult, but a finer surface is achieved after turning, while a higher S content results in an increased fraction of softer sulfide inclusions, which reduce the cutting forces but also result in a reduced surface quality. turning, while a higher S content results in an increased fraction of softer sulfide inclusions, which reduce the cutting forces but also result in a reduced surface quality. |
|---|
| Ključne besede: | non-metallic inclusions, mechanical properties, machinability, surface roughness |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Datum objave: | 28.08.2024 |
|---|
| Založnik: | MDPI |
|---|
| Leto izida: | 2024 |
|---|
| Št. strani: | str. 1-16 |
|---|
| Številčenje: | Vol. 14, iss. 9 |
|---|
| Izvor: | Švica |
|---|
| PID: | 20.500.12556/DiRROS-20314  |
|---|
| UDK: | 620.1 |
|---|
| ISSN pri članku: | 2075-4701 |
|---|
| DOI: | 10.3390/met14090977 |
|---|
| COBISS.SI-ID: | 206205699 |
|---|
| Avtorske pravice: | © 2024 by the authors |
|---|
| Opomba: | Nasl. z nasl. zaslona;
Opis vira z dne 3. 9. 2024;
Št. članka: 977;
|
|---|
| Datum objave v DiRROS: | 03.09.2024 |
|---|
| Število ogledov: | 261 |
|---|
| Število prenosov: | 450 |
|---|
| Metapodatki: |    |
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
