| Naslov: | Tribocorrosive study of new and in vivo exposed nickel titanium and stainless steel orthodontic archwires |
|---|
| Avtorji: | ID Kosec, Tadeja (Avtor)
ID Močnik, Petra (Avtor)
ID Mezeg, Uroš (Avtor)
ID Legat, Andraž (Avtor)
ID Ovsenik, Maja (Avtor)
ID Jenko, Monika (Avtor)
ID Grant, John T. (Avtor)
ID Primožič, Jasmina (Avtor) |
|---|
| Datoteke: |  URL - Izvorni URL, za dostop obiščite https://www.mdpi.com/2079-6412/10/3/230
 PDF - Predstavitvena datoteka, prenos (2,18 MB)
MD5: 6DD45907D12075E10F30B79C9412533D
|
|---|
| Jezik: | Angleški jezik |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: |  ZAG - Zavod za gradbeništvo Slovenije
|
|---|
| Povzetek: | The surface, corrosion and wear properties of new and in vivo exposed nickel titanium (NiTi) and stainless steel (SS) archwires used in orthodontic treatment were investigated. Electrochemical and tribo-electrochemical tests in artificial saliva were performed in order to define corrosion properties and to estimate wear rate of new and in vivo exposed NiTi and SS archwires. The surface chemical analysis of the passive film on the NiTi and SS archwires before and after tribocorrosion tests was performed by Auger Electron Spectroscopy (AES). In vivo exposed NiTi and SS archwires had better electrochemical properties than new archwires due to the protective nature of oral deposits. Total wear and coefficients of friction were higher among in vivo exposed archwires and higher in NiTi archwires in comparison to SS archwires. The estimated thickness of the TiO2 passive film on as-received NiTi is 8 nm, while the passive Cr2O3 film on as-received SS is just 1–2 nm. On in vivo exposed NiTi archwire, a 60–80 nm thick organic film/dental plaque was observed, and on SS, it was thinner, at about 60 nm. This research shows the importance of combining AES with electrochemical testing, to characterize tribocorrosive properties of NiTi and SS orthodontic archwires. |
|---|
| Ključne besede: | archwires, NiTi, stainless steel, wear |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Datum objave: | 03.03.2020 |
|---|
| Založnik: | MDPI AG |
|---|
| Leto izida: | 2020 |
|---|
| Št. strani: | str. 1-11 |
|---|
| Številčenje: | Vol. 10, iss. 3 |
|---|
| PID: | 20.500.12556/DiRROS-16829  |
|---|
| UDK: | 544.5/.6 |
|---|
| ISSN pri članku: | 2079-6412 |
|---|
| DOI: | 10.3390/coatings10030230 |
|---|
| COBISS.SI-ID: | 2566759 |
|---|
| Avtorske pravice: | © 2020 by the authors. Licensee MDPI, Basel, Switzerland. |
|---|
| Opomba: | Nasl. z nasl. zaslona;
Opis vira z dne 10. 3. 2020;
Članek št. 136;
Št. članka: 230;
|
|---|
| Datum objave v DiRROS: | 24.08.2023 |
|---|
| Število ogledov: | 738 |
|---|
| Število prenosov: | 290 |
|---|
| Metapodatki: |    |
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
