1. Experimental investigation of the shear force capacity of prismatic cross laminated timber beamsHenrik Danielsson, Tomaž Pazlar, Erik Serrano, Boris Azinović, 2024, izvirni znanstveni članek Povzetek: Experimental tests of Cross Laminated Timber (CLT) under in-plane beam loading conditions are presented. The influence of the element layup, the individual lamination width, and the beam overhang at the supports on the shear force capacity was investigated. All the CLT beams had the same gross cross section, and a 4-point-bending test setup was used. The experimentally determined load-bearing capacities are compared with the load-bearing capacities resulting from analytical methods proposed for structural design, focusing on shear failure in the crossing areas of flatwise bonded laminations (shear failure mode III). The test results indicate no or very small influence of the element layup and the lamination width on the shear force capacity. These results partly contradict the predictions of the proposed design methods. Of the three studied beam geometry parameters, the beam overhang at the support had the greatest influence on the load-bearing capacity.
Ključne besede: cross laminated timber, CLT, beam, shear testing, shear capacity, design methods
Objavljeno v DiRROS: 15.04.2024; Ogledov: 145; Prenosov: 73
 Celotno besedilo (3,32 MB)
Gradivo ima več datotek! Več... |
2. Experimental investigation of the axial strength of glued-in rods in cross laminated timberBoris Azinović, Erik Serrano, Miha Kramar, Tomaž Pazlar, 2018, izvirni znanstveni članek Povzetek: This paper presents results from an experimental assessment of glued-in rods in cross laminated timber (CLT). For the purposes of the study more than 60 pull-pull tests were performed, where the specimens varied in terms of bonded-in length (from 80 to 400 mm), rod diameter (16-24 mm) and rod-to-grain angle (parallel and perpendicular). Several different failure modes that are not common for other applications of glued-in rods (e.g., a failure between CLT layers) were obtained for the analysed CLT specimens. It was found that these failure mechanisms can substantially influence the obtained ultimate tension loads. At the end, the experimental results were compared with empirical and semi-empirical equations for estimating the pull-out strength of glued-in rods in structural timber and glulam. The comparison showed that most of the existing equations overestimate the ultimate tension loads for specimens with the rod parallel to the grain and underestimate the ultimate tension load for specimens with the rod perpendicular to the grain. The results vary because the possible CLT failure modes were not included in previous studies. Further studies are proposed to improve the equations for glued-in rods in CLT.
Ključne besede: glued-in rods, cross laminated timber (CLT), pull-pull experiment, glued-in length, rod-to-grain angle, failure mechanisms in CLT
Objavljeno v DiRROS: 29.11.2023; Ogledov: 225; Prenosov: 179
Celotno besedilo (4,13 MB)
Gradivo ima več datotek! Več... |
3. Glued-in rods in cross laminated timber - numerical simulations and parametric studiesBoris Azinović, Henrik Danielsson, Erik Serrano, Miha Kramar, 2019, izvirni znanstveni članek Povzetek: Numerical simulations and parametric studies of glued-in rods in cross-laminated timber have been performed. The simulations were based on 3D finite element analysis, using a cohesive surface model for the bond-lines between the laminations and the bond-line along the rod. The parametric studies investigated the influence of the glued-in length, the rod diameter, and the rod-to-grain angle on the load-bearing capacity and stiffness of the connection. The analyses showed that the load-bearing capacity generally increases with the glued-in length and the rod diameter, which agrees well with experiments. For different rod-to-grain angles, different mechanical behaviour was observed, especially considering the failure modes.
Ključne besede: glued-in rods, cross laminated timber (CLT), parametric study, nonlinear numerical modelling, glued-in length, rod diameter, rod orientation
Objavljeno v DiRROS: 13.09.2023; Ogledov: 252; Prenosov: 153
Celotno besedilo (2,66 MB)
Gradivo ima več datotek! Več... |
