Digitalni repozitorij raziskovalnih organizacij Slovenije

Iskanje po repozitoriju
A+ | A- | Pomoč | SLO | ENG

Iskalni niz: išči po
išči po
išči po
išči po

Možnosti:
  Ponastavi


Iskalni niz: "avtor" (%C5%A0krgat Sabina) .

41 - 50 / 64
Na začetekNa prejšnjo stran1234567Na naslednjo stranNa konec
41.
Impact of metakaolin on mechanical performance of flax textile-reinforced cement-based composites
Filip Majstorović, Václav Sebera, Maruša Mrak, Sabina Dolenec, Marco Wolf, Laetitia Sarah Jennifer Marrot, 2022, izvirni znanstveni članek

Povzetek: This study presents research on the effect of Portland cement (PC) replacement with metakaolin on the mechanical behavior of flax textile-reinforced cementitious matrices (TRCM). The composition of cementitious matrices and in-situ flax fibres was determined using X-ray diffraction and thermogravimetric analysis, while the reinforcement efficiency of the textile and mechanical behavior of TRCMs was investigated by three-point bending tests and finite element analysis. High amounts of PC replacement with metakaolin provided a calcium hydroxide-free environment, more suitable for the natural fibres, to avoid their degradation and embrittlement and, thus, significantly contribute to the ductility of the cement-based composite material.
Ključne besede: textile-reinforced concrete (TRC), flax textile, natural fibres, finite element, metakaolin, cement-based composites, open access
Objavljeno v DiRROS: 22.05.2023; Ogledov: 372; Prenosov: 175
.pdf Celotno besedilo (8,40 MB)
Gradivo ima več datotek! Več...

42.
Radiological and physico-chemical characterization of red mud as an Al-containing precursor in inorganic binders for the building industry
Ljiljana Kljajević, Miljana Mirković, Sabina Dolenec, Katarina Šter, Mustafa Hadžalić, Ivana Vukanac, Miloš Nenadović, 2021, izvirni znanstveni članek

Povzetek: The potential re-use of red mud in the building and construction industry has been the subject of research of many scientists. The presented research is a contribution to the potential solution of this environmental issue through the synthesis of potential construction materials based on red mud. A promising way of recycling these secondary raw materials is the synthesis of alkali-activated binders or alkali activated materials. Alkali-activated materials or inorganic binders based on red mud are a new class of materials obtained by activation of inorganic precursors mainly constituted by silica, alumina and low content of calcium oxide. Since red mud contains radioactive elements like 226Ra and 232Th, this may be a problem for its further utilization. The content of naturally occurring radionuclides in manufactured material products with potential application in the building and construction industry is important from the standpoint of radiation protection. Gamma radiation of the primordial radionuclides, 40K and members of the uranium and thorium series, increases the external gamma dose rate. However, more and more precedence is being given to limiting the radiological dose originating from building materials on the population these days. The aim of this research was to investigate the possible influence of alkali activation-polymerization processes on the natural radioactivity of alkali activated materials synthesized by red mud (BOKSIT a. d. Milići, Zvornik, Bosnia and Herzegovina) and their structural properties. This research confirmed that during the polymerization process the natural radioactivity was reduced, and that the process of alkali activation of raw materials has an influence on natural radioactivity of synthesized materials.
Ključne besede: red mud, inorganic binder, DRIFT, natural radioactivity, gamma index, building industry
Objavljeno v DiRROS: 12.05.2023; Ogledov: 367; Prenosov: 111
.pdf Celotno besedilo (962,61 KB)
Gradivo ima več datotek! Več...

43.
Potential usage of hybrid polymers binders based on fly ash with the addition of PVA with satisfying mechanical and radiological properties
Miljana Mirković, Ljiljana Kljajević, Sabina Dolenec, Miloš Nenadović, Vladimir Pavlović, Milica Rajačić, Snežana B. Nenadović, 2021, izvirni znanstveni članek

Povzetek: Since recycled technologies usage is mandatory for environmental safety, and in this regard, it is important to examine new materials that can be used in construction and are primarily produced from fly ash. In addition to characteristics such as hardness and compressive strength, the given materials must also be radiologically and environmentally safe. The main concept of engineered geopolymer gel composites based on fly ash residues is focused on developing binder materials via gel formation processes that can replace ordinary cement materials. This study is unique in researching the potential use of fly ash from the Nikola Tesla thermal power plant in Serbia, where the hybrid geopolymeric materials synthesized from fly ash are experimentally examined with the addition 1 wt% and 2 wt% of polyvinyl alcohol (PVA). This paper aims to investigate the structural, morphological, mechanical, and radiological properties of hybrid materials with the addition of PVA and without additive in the period of ageing for 28 days at room temperature. The phase composition was investigated using X-ray powder diffraction (XRPD) analysis, while morphological characteristics of these materials were examined using scanning electron microscopy and energy dispersive X-ray analysis (SEM-EDS). Vibrational spectra of obtained samples are investigated using diffuse reflectance infrared Fourier transform (DRIFT) and Fourier transform infrared (FTIR) techniques. The hardness and compressive strength are also examined, indicating that the 1 wt% addition in geopolymeric matrix results in the best mechanical properties. Radiological measurements of investigated all geopolymer samples show decreasing activity concentrations of radionuclides for 50% compared to fly ash.
Ključne besede: geopolymer gel, inorganic binders, hybrid materials, fly ash, radiological properties, strength, open access
Objavljeno v DiRROS: 12.05.2023; Ogledov: 294; Prenosov: 135
.pdf Celotno besedilo (1,61 MB)
Gradivo ima več datotek! Več...

44.
Report of RILEM TC 267-TRM phase 3 : validation of the R3 reactivity test across a wide range of materials
Diana Londono-Zuluaga, Sabina Dolenec, Maruša Mrak, 2022, izvirni znanstveni članek

Povzetek: RILEM TC 267 TRM– “Tests for Reactivity of Supplementary Cementitious Materials” recommends the Rapid Reliable Relevant (R3) test as a method for determining the chemical reactivity of supplementary cementitious materials (SCMs) in Portland cement blends. In this paper, the R3 test was applied to 52 materials from a wide range of conventional and alternative SCMs with the aim to validate such test. An excellent correlation was found between the cumulative heat release and the bound water determined following the R3 test method. Comparison of the R3 test results to mortar compressive strength development showed that all conventional SCMs (e.g. blast furnace slag and fly ashes) followed the same trend, with the notable exception of very reactive calcined kaolinitic clays. It is discussed, through an in-depth statistical regression analysis of the R3 reactivity test results and the 28 days relative compressive strengths, how reactivity threshold values for classification of the chemical reactivity of SCMs could be proposed based on the R3 test results.
Ključne besede: supplementary cementitious materials, reactivity test, heat release, bound water, compressive strength
Objavljeno v DiRROS: 26.04.2023; Ogledov: 249; Prenosov: 139
.pdf Celotno besedilo (2,15 MB)
Gradivo ima več datotek! Več...

45.
Report of RILEM TC 267-TRM phase 2 : optimization and testing of the robustness of the R3 reactivity tests for supplementary cementitious materials
François Avet, Sabina Dolenec, Maruša Mrak, 2022, izvirni znanstveni članek

Povzetek: The results of phase 1 of an interlaboratory test, coordinated by the RILEM TC 267-TRM “Tests for Reactivity of Supplementary Cementitious Materials” showed that the R3 (rapid, relevant, reliable) test method, by measurement of heat release or bound water, provided the most reliable and relevant determination of the chemical reactivity of supplementary cementitious materials (SCMs), compared to other test methods. The phase 2 work, described in this paper aimed to improve the robustness of the test procedure and to develop precision statements for the consolidated test procedure. The effect of the pre-mixing and mixing conditions, and the impact of the mix design on the test method robustness were assessed and fixed for optimal conditions to carry out the R3 heat release test. The effect of the drying step was evaluated to define the R3 bound water test procedure in more detail. Finally, the robustness of the consolidated final test methods was determined by an interlaboratory study to define the precision statements.
Ključne besede: supplementary cementitious materials, reactivity test, bound water
Objavljeno v DiRROS: 26.04.2023; Ogledov: 312; Prenosov: 122
.pdf Celotno besedilo (1,07 MB)
Gradivo ima več datotek! Več...

46.
Influence of alkalis on the phase development of belite-sulfoaluminate clinkers
Barbara Čeplak, Katarina Šter, Maruša Mrak, Luka Škrlep, Mirijam Vrabec, Sabina Dolenec, 2022, izvirni znanstveni članek

Povzetek: This paper presents a study on the influence of different amounts of alkalis (K2O and Na2O) on clinker phase formation, microstructure, phase composition and reactivity of belite-sulfoaluminate cement clinker. Using X-ray powder diffraction and scanning electron microscopy with energy dispersive spectrometry, it was found that the amount of C2S and C4AF increases with the incorporation of alkalis, while the amount of C4A3Ś and CŚ decreases. In addition to the major phases, the samples with alkalis also consist of minor phases such as C3A (tricalcium aluminate), KŚ (arcanite), and KC2Ś3 (Ca-langbeinite). The major ions in the major phases were substituted by alkali cations and some other ions (Ca2+, Al3+, Fe3+, S2-, S6+, Si4+). The alkalis also affect the microstructure of the clinker, e.g., the shape of the grains. Consequently, isothermal calorimetry was used to detect differences in hydration kinetics. The clinker with 2 wt. % K2O content was the most reactive, while the sample with 0.5 wt. % Na content was the least reactive. The latter was primarily influenced by the content of the main and minor phases of the clinker.
Ključne besede: BCSA clinker, microstrcuture, reactivity, alkalis, open access
Objavljeno v DiRROS: 06.12.2022; Ogledov: 533; Prenosov: 268
.pdf Celotno besedilo (4,45 MB)
Gradivo ima več datotek! Več...

47.
48.
Priročnik za bolnike z izločalno stomo
Andreja Klinc, Dragica Tomc, Sabina Medjedović, 2021, slovar, enciklopedija, leksikon, priročnik, atlas, zemljevid

Ključne besede: rak črevesja, rak sečil, stoma
Objavljeno v DiRROS: 14.07.2022; Ogledov: 618; Prenosov: 195
.pdf Celotno besedilo (769,40 KB)

49.
Building of the Al-Containing secondary raw materials registry for the production of low CO2 mineral binders in South-Eastern European region
Gorazd Žibret, Klemen Teran, Lea Žibret, Katarina Šter, Sabina Dolenec, 2021, izvirni znanstveni članek

Povzetek: The bottleneck in the process for increasing production of low CO2 mineral binders, based on BCSA (belite sulfoaluminate) clinkers, is the availability of Al-rich raw materials. For that purpose, a new registry of Al-containing secondary mineral residues (industrial and mine waste) has been developed and is presented in this paper. The methodology of creating the registry consists of three main steps: Gathering ideas, consolidation of ideas, and implementation. In order to achieve this, the following methodology was adopted: Analysis of similar registries by potential end-users and seeking potential solutions and tools to be used, and conducting 3 rounds of stakeholder consultations via workshops in order to determine crucial parameters and features the registry needs to contain. The key discussion points were about which data the registry needs to contain, who shall be the potential users, and what are the stakeholderʼs expectations from the registryʼs portal. Potential individual registry variables were identified as being relevant/irrelevant or available/unavailable, and potential solutions for the registrys sustainability were explored. Each Al-rich waste/residue data entry is divided into 10 slots, describing legal status, location, quantities, chemical (REE included), mineralogical, physical and radiological properties, life-cycle assessment, additional data, and data relevancy. The registry will act as a matchmaking tool between producers/holders of Al-rich secondary raw materials and potential producers of cement clinkers.
Ključne besede: cement, belite sulfoaluminate clinker, waste, by--product, deležniki
Objavljeno v DiRROS: 10.06.2022; Ogledov: 539; Prenosov: 324
.pdf Celotno besedilo (2,23 MB)
Gradivo ima več datotek! Več...

50.
The valorisation of selected quarry and mine waste for sustainable cement production within the concept of circular economy
Emilija Fidanchevski, Katarina Šter, Maruša Mrak, Ljiljana Kljajević, Gorazd Žibret, Klemen Teran, Bojan Poletanovic, Monika Fidanchevska, Sabina Dolenec, Ildikó Merta, 2022, izvirni znanstveni članek

Povzetek: The cement industry could potentially consume large amounts of solid industrial waste in order to improve its sustainability. The suitability of selected quarry and mine waste as secondary raw materials (SRM) was examined for the sustainable production of cement following the concept of a circular economy. The chemical, mineralogical, and radiological characterization of SRM was conducted in this study. Its potential use in low-carbon and low-energy belite-sulfoaluminate cement was investigated by incorporating the examined SRM into cement clinker. Various characterization methods were used to characterize the cement, including X-ray powder diffraction (XRD), thermal analysis (DTA/TG), and isothermal calorimetry. Depending on the chemical composition of the waste, lower or higher amounts were allowed to be incorporated into the raw clinker mixture for a targeted clinker phase composition. Among the samples, differences were observed in the phase composition of synthesized clinkers, which slightly influenced the reactivity of the cement but did not significantly change the compressive strength of the final product.
Ključne besede: mineralne surovine, rudarski odpadki, rudniki, kamnolomi, cement, klinker, krožno gospodarstvo, BCSA clinker, cement, circular economy, clinker, mine wastes, quarry waste
Objavljeno v DiRROS: 10.06.2022; Ogledov: 606; Prenosov: 319
.pdf Celotno besedilo (3,34 MB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.25 sek.
Na vrh