Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Povzetek: As-produced and heat-treated TiAlV samples were prepared by selective laser melting and compared to wrought samples of identical chemical composition. Microstructural, corrosion, and spectroscopic studies of additively manufactured samples in artificial saliva at 37 °C, with NaF and at pH 2.3 were as a novelty combined with metal ion release during 42 days immersion. In artificial saliva higher amount of ions was released on SLM specimen when compared to wrought alloy. The total amount of ions released from SLM specimen in AS containing NaF was 10-times higher than in AS, while in AS with lactic acid it was 100-times higher.
Ključne besede: Ti6Al4V, SLM, corrosion, ion release, XPS, ToF-SIMS
Objavljeno v DiRROS: 31.05.2023; Ogledov: 331; Prenosov: 265
Celotno besedilo (15,86 MB)
Gradivo ima več datotek! Več...

Povzetek: The ever-growing worldwide demand for fired clay brick has resulted in the shortage of clay in many parts of the world. Therefore, there is a need to look for more sustainable alternative materials for the brick manufacturing. This study has investigated the potential use of the untreated Drava River sediment as a substitute material for clay in the production of fired bricks, with the research being conducted at both laboratory and industrial level. At the laboratory level, brick specimens were prepared by mixing clay with different river sediment proportions (ranging from 10 to 50 wt%) and were fired at 950 °C, with microstructural and various physical–mechanical properties being analyzed. Elevated carbonate content in Drava river sediment results in higher weight loss during firing at temperatures up to 950 °C, comparing to firing pure brick-making clay. Consequently, the addition of sediment increases porosity of fired bricks, which results in lowering of their mechanical properties. Results reveal that the compressive strength of the pure clay sample was 79.5 MPa, while the compressive strength of the sample with the addition of river sediment from 10 wt% to 50 wt% decreased from 73.9 MPa to 26.2 MPa, respectively. Despite the lower compressive strength, the 26.2 MPa is still above the limit value of 10 MPa specified in the standard EN 772–1 [1]. At the industrial level, hollow clay bricks were prepared with 20 wt% of the river sediment and fired in a tunnel kiln. Inclusion of the river sediment also decreased compressive strength from 38 MPa for pure mixture to 26 MPa for 20 wt% of the sediment addition, confirming usability of Drava sediment in brick production. In addition, LCA study has been conducted to evaluate the environmental impacts associated with the industrial production of classic bricks and bricks with the addition of the river sediment. The obtained results have shown that the bricks made with the addition of the Drava River sediment are sustainable and environmentally friendly and meet all the requirements specified in the relevant regulatory standard.
Ključne besede: sediments, clay masonry units, LCA, properties
Objavljeno v DiRROS: 30.05.2023; Ogledov: 331; Prenosov: 238
Celotno besedilo (4,76 MB)
Gradivo ima več datotek! Več...

Povzetek: The main objective of the EU-funded project mitigating environmentally-assisted cracking through optimisation of surface condition (MEACTOS) was to gain knowledge on the ability of different surface machining procedures to mitigate environmentally-assisted cracking (EAC) in typical light water reactor structural materials and environments. Surfaces of cold-worked (CW) type 316L austenitic stainless steel and nickel-based weld metal Alloy 182 flat tapered tensile specimens were machined using different processes. EAC initiation susceptibility of these specimens was evaluated using constant extension rate tensile (CERT) tests under simulated boiling water reactor (BWR) and pressurized water reactor (PWR) conditions and assessed using constant load experiments. More than a hundred tests were performed covering about 10 years of autoclave testing time. Only minor or no measurable improvements in EAC initiation susceptibility as a function of surface treatments (grinding or advanced machining) compared to the standard industrial face milling were demonstrated. In most cases, the stress thresholds for EAC initiation determined in constant load tests confirmed the trend obtained from CERT tests. This paper summarises the most important results and conclusions concerning the EAC initiation behaviour for the CW 316L and Alloy 182 under reducing PWR and oxidizing BWR conditions.
Ključne besede: crack initiation, environmentally-assisted cracking, Alloy 182, AISI 304 stainless steel, surface treatment, light water reactor, open access
Objavljeno v DiRROS: 30.05.2023; Ogledov: 370; Prenosov: 206
Celotno besedilo (16,31 MB)
Gradivo ima več datotek! Več...

Povzetek: With wood regaining substantial interest as a construction material due to sustainability concerns and aesthetics trends, efficient and safe protection methods are needed to prevent the discouloration and the loss of mechanical properties of this renewable and UV-sensitive material. In this study, sustainable coatings comprising 0 to 20 wt % biocarbon (BC) dispersed in tung oil were developed for wood protection. BC particles were added as ultraviolet (UV) absorbers and were produced by various carbonization routes. The BC powders were characterized in terms of particle size and surface functional groups by Fourier-Transform infrared, and the UV and visible absorbance of dispersed BC powders in water solutions were related to these characteristics. Two wooden substrates (beech and oak) were coated with the developed coatings and the samples underwent six months of onsite weathering. While the total colour change of uncoated samples and tung oil-coated substrates without BC kept increasing over time and resulted in a clear alteration of the wood surface aesthetics, an increased BC content in the coatings led to enhanced colour stability, with alteration of the colour close to 2 for both wood species after six months of weathering for 10 and 20 wt% BC. Coating with tung oil made the wooden substrates, initially hydrophilic, become hydrophobic, and the further introduction of biocarbon increased hydrophobicity. However, the increase in BC content was not correlated with an increase in water repellence, the highest water contact angle being observed for 5 % BC, and no further improvement in hydrophobicity was observed with higher BC content. The weathering negatively affected the water repellence of all the samples (i.e., reference samples and coated samples with various BC content). However, the introduction of 20 % BC best protected the decrease in water repellence induced by the onsite weathering.
Ključne besede: biocarbon, biochar, coating, wood protection, hydrophobic coating, wettability
Objavljeno v DiRROS: 30.05.2023; Ogledov: 362; Prenosov: 429
Celotno besedilo (6,19 MB)
Gradivo ima več datotek! Več...

Povzetek: To increase the sustainability of prefabricated timber buildings and constructions, composite timber beams with “box” cross-sections were developed in collaboration with an industry partner. They were constructed from a solid timber frame and from webs made of residual waste wood- particle boards from prefabricated timber buildings production. The developed beams’ design concepts presented in this paper were governed by architectural features of prefabricated timber buildings, geometrical limitations, available production technology, and structural demand related to various possible applications. The paper presents the results of experimental bending tests of six variations of the developed composite timber beams constructed by mechanical fasteners only. The developed design concept of composite timber beams without adhesives is beneficial compared to glued beams in terms of design for deconstruction and lower VOC emissions. The tests were conducted to study the influence of the following parameters on the beams’ mechanical behavior: (i) web material (oriented strand boards (OSBs) vs. cement-particle boards); (ii) the influence of beam timber frame design (flanges and web stiffeners vs. flanges, web stiffeners, and compressive diagonals), and (iii) the influence of stiffener–flange joint design. Besides the beams’ load-bearing capacities, their linear and non-linear stiffness characteristics were the main research interest. While adding compressive timber diagonals did not prove to significantly increase the stiffness of the beams in the case of cement-particle board webs, it increased their load-bearing capacity by enabling the failure of flanges instead of prior webs and stiffener–flange joints failure. For beams with OSB webs, failure of the bottom flange was achieved already with the “basic” timber frame design, but timber diagonals proved beneficial to increase the stiffness characteristics. Finally, mechanical characteristics of the developed beams needed in structural design for their application are provided together with further development guidelines.
Ključne besede: composite timber beam, box beam, OSB, cement-particle boards, innovative engineered wood product, experimental tests, flexural performance, mechanical fasteners, open access
Objavljeno v DiRROS: 29.05.2023; Ogledov: 288; Prenosov: 166
Celotno besedilo (7,82 MB)
Gradivo ima več datotek! Več...