1. Diketopyrrolopyrrole pigment core@multi-layer ▫$SiO_2$▫ shell with improved photochemical stabilityErika Švara Fabjan, Zineb Saghi, Paul A. Midgley, Mojca Otoničar, Goran Dražić, Miran Gaberšček, Andrijana Sever Škapin, 2018, izvirni znanstveni članek Povzetek: A model organic pigment (diketopyrrolopyrrole) is encapsulated by a silica coating in order to improve its photochemical stability. Unlike in previous works where single-layer silica coatings were used for similar purposes, we here propose creation of a multi-layer silica shell synthesized via in-situ sol-gel method, which should significantly improve the homogeneity and thus the protection ability of the coating. This is done by repeating the basic two-step process (pigment surface modification and silica encapsulation) several times, creating the final protective shell in a layer-by-layer fashion. The compositional and structural properties of the prepared coatings is studied using Fourier-transform infrared spectroscopy, differential thermal and thermogravimetric analysis, nitrogen adsorption measurements and transmission electron microscopy. Photochemical stability of non-encapsulated and encapsulated pigment particles is evaluated via the so-called fast-irradiation method. Various correlations between the essential coating properties, such as thickness, porosity, SiO2 content, and the corresponding photochemical stability of the samples are established and discussed in detail. As a whole, our results confirm the basic hypothesis, that multiple-layered silica shells show improved pigment protection ability in comparison to the single-layer coatings.
Ključne besede: organic pigments, silica coating, encapsulation, morphology, photocemical stability
Objavljeno v DiRROS: 27.03.2024; Ogledov: 122; Prenosov: 54
 Celotno besedilo (1,78 MB)
Gradivo ima več datotek! Več... |
2. Flame spread behaviour of Polydimethylsiloxane (PDMS) membranes in 1 g and µg environmentsWilson Ulises Rojas Alva, Frederik Møller-Poulsen, Sze Lok Man, Cameron Creamer, David Hanna, Grunde Jomaas, 2022, izvirni znanstveni članek Povzetek: Diffusion flame behaviour and silica ash (SiO2) production were experimentally studied for various Polydimethylsiloxane (PDMS) membrane thicknesses (0.125 mm to 1.0 mm) in normal gravity and during microgravity flight experiments. The flames were established on vertical samples (300 mm in length) and subjected to either opposed or concurrent forced flows (both laminar and turbulent), assimilating the NASA Test 1 that is in use for spacecraft material selection. The opposed flame spread rate was observed to be steady and could be estimated using classical theory. Under concurrent flow, the flame spread rate was only steady for very high forced flows. The opposed flame-spread rate ranged from 0.5 to 1.5 mm/s, while the concurrent case ranged between 0.1 and 12 mm/s. The transport of silica ash (SiO2) was found to affect the heat balance of the concurrent flame spread in a manner that resulted in unsteady flame spread. For opposed flame spread, on the other hand, the transport of silica ash showed to be irrelevant. The extinction behaviour for the concurrent flame spread was heavily dominated by the transport of silica-ash, while for opposed flames, extinction was due to kinetics (at high forced flows). In microgravity environments, the transport and deposition of silica ash is anticipated to dominate flame spread and near-limit as well. These results suggest that silica-based products might be less flammable in microgravity than other similar materials such as common thermoplastics (PP or PE) used as wire jackets.
Ključne besede: silicone burning, spacecraft fire safety, flame spread, near-limit, silica-ash
Objavljeno v DiRROS: 13.11.2023; Ogledov: 315; Prenosov: 81
Celotno besedilo (1,61 MB)
Gradivo ima več datotek! Več... |
3. Colorimetric cutoff indication of relative humidity based on selectively functionalized mesoporous silicaErika Švara Fabjan, Peter Nadrah, Anja Ajdovec, Matija Tomšič, Goran Dražić, Matjaž Mazaj, Nataša Zabukovec Logar, Andrijana Sever Škapin, 2020, izvirni znanstveni članek Povzetek: We present a novel % cutoff concept of colorimetric indication of relative humidity based on dye dissolution in condensed water in capillaries of selectively functionalized mesoporours host SiO2 material. Consistently high levels of indoor air humidity induces mold and algae growth which represent a potential risks for human health and have deteriorating effect on walls as well. Simple localized humidity detection of high humidity with naked eye especially at places with low air circulation, where growth of mold usually starts first, is therefore highly desirable. The reporting dye was integrated in the non-functionalized mesoporous silica matrix with different pore diameters and selective-functionalized mesoporous silica material. After exposure to the environment of different air humidities the dye dissolved in water causing color change of adsorbent. With the use of adsorbents with different mesopore diameters high ability to tune the value of relative humidity when complete capillary condensation occurred was achieved. Materials with pore diameters of 3.0%nm, 3.5%nm and 7.0%nm exhibit gradual color change when reaching relative humidity up to 55, 79 and 88 RH% respectively. After selective methylation of the material with 7.0%nm pore diameter, non-gradual cutoff color change was achieved. Sample exhibited color change at narrow range of relative humidity (cutoff color change). Due to selective functionalized outer surface the dye dissolution occur only in condensed water in pores and therefore provide colorimetric indication only in this range. Selectively modified silica material has a great potential for a straightforward detection of high humid environment.
Ključne besede: turn-on colorimetric probe, selective functionalization, mesoporous silica, relative humidity, capillary condensation
Objavljeno v DiRROS: 05.09.2023; Ogledov: 302; Prenosov: 223
Celotno besedilo (7,18 MB)
Gradivo ima več datotek! Več... |
4. RILEM TC 247-DTA round robin test : sulfate resistance, alkali-silica reaction and freeze-thaw resistance of alkali-activated concretesFrank Winnefeld, Gregor J. G. Gluth, Susana Bernal, Maria Chiara Bignozzi, Lorenza Carabba, Sundararaman Chithiraputhiran, Alireza Dehghan, Sabina Dolenec, Katja Dombrowski-Daube, Ashish Dubey, Vilma Ducman, Yu Jin, Karl Peterson, Stephen Dietmar, John L. Provis, 2020, izvirni znanstveni članek Povzetek: The RILEM technical committee TC 247-DTA ‘Durability Testing of Alkali-Activated Materials’ conducted a round robin testing programme to determine the validity of various durability testing methods, originally developed for Portland cement based-concretes, for the assessment of the durability of alkali-activated concretes. The outcomes of the round robin tests evaluating sulfate resistance, alkali-silica reaction (ASR) and freeze–thaw resistance are presented in this contribution. Five different alkali-activated concretes, based on ground granulated blast furnace slag, fly ash, or metakaolin were investigated. The extent of sulfate damage to concretes based on slag or fly ash seems to be limited when exposed to an Na2SO4 solution. The mixture based on metakaolin showed an excessive, very early expansion, followed by a dimensionally stable period, which cannot be explained at present. In the slag-based concretes, MgSO4 caused more expansion and visual damage than Na2SO4; however, the expansion limits defined in the respective standards were not exceeded. Both the ASTM C1293 and RILEM AAR-3.1 test methods for the determination of ASR expansion appear to give essentially reliable identification of expansion caused by highly reactive aggregates. Alkali-activated materials in combination with an unreactive or potentially expansive aggregate were in no case seen to cause larger expansions; only the aggregates of known very high reactivity were seen to be problematic. The results of freeze–thaw testing (with/without deicing salts) of alkali-activated concretes suggest an important influence of the curing conditions and experimental conditions on the test outcomes, which need to be understood before the tests can be reliably applied and interpreted.
Ključne besede: alkali-activated materials/geopolymers, sulphate resistance, alkali silica reactivity, freeze-thaw resistance, Rilem TC
Objavljeno v DiRROS: 17.08.2023; Ogledov: 226; Prenosov: 163
Celotno besedilo (560,56 KB)
Gradivo ima več datotek! Več... |
