Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Objavljeno v DiRROS: 15.09.2023; Ogledov: 359; Prenosov: 64
Celotno besedilo (178,75 KB)

Povzetek: Not only is the energy efficiency of buildings nowadays becoming more and more important; the legislative requirements, the people’s awareness of the environmental questions and their thermal comfort expectations are also on a much higher level. All of these issues can be addressed by making the building envelope more thermally resistant. However, with the traditional thermal insulation materials the thickness of thermal insulation layers is already at the viable limits. Therefore, the development of new, more efficient thermal insulation products with a higher thermal resistance is highly promoted. Preliminary research results can be applied to models to develop and confirm the conceptual designs of such new materials. In this paper, an analysis of thermal performance is presented for a novel thermal insulation consisting of graphite polystyrene (GPS) matrix with cavities filled with an insulative gas, and a protective sheath to prevent it from leaking. Bearing in mind the suitability for later production, different configurations of the assembly were considered, regarding the matrix geometry, the type of the gas filling, and the surface emissivity of the cavities. A range of numerical simulations of heat transfer was conducted to determine the efficiency of different designs in reducing the conductive, the convective, and the radiative heat transfer. Advantages, limitations and some detailed parameters of the proposed design concepts were determined, which were then used for optimisation. The analysis of the results indicates that the equivalent thermal conductance of a GPS panel can be significantly reduced by the introduction of gas-filled cavities. The reduction is highly dependent on the type of the gas filling (thermal conductivity, viscosity, specific heat, etc.), the size of the cavities, and the cavity surface emissivity.
Ključne besede: gas-filled cavities, graphite polystyrene, numerical simulation, thermal insulation
Objavljeno v DiRROS: 15.09.2023; Ogledov: 262; Prenosov: 122
Celotno besedilo (1,21 MB)
Gradivo ima več datotek! Več...

Povzetek: Numerical simulations and parametric studies of glued-in rods in cross-laminated timber have been performed. The simulations were based on 3D finite element analysis, using a cohesive surface model for the bond-lines between the laminations and the bond-line along the rod. The parametric studies investigated the influence of the glued-in length, the rod diameter, and the rod-to-grain angle on the load-bearing capacity and stiffness of the connection. The analyses showed that the load-bearing capacity generally increases with the glued-in length and the rod diameter, which agrees well with experiments. For different rod-to-grain angles, different mechanical behaviour was observed, especially considering the failure modes.
Ključne besede: glued-in rods, cross laminated timber (CLT), parametric study, nonlinear numerical modelling, glued-in length, rod diameter, rod orientation
Objavljeno v DiRROS: 13.09.2023; Ogledov: 235; Prenosov: 144
Celotno besedilo (2,66 MB)
Gradivo ima več datotek! Več...

Povzetek: The importance of thermal modification is increasing worldwide. Increased use of thermally modified timber (TMT) has resulted in a need for reliable quality control, comprising control of variation of the production within defined limits, allowing third-party control in the case of certification and the regulation of customer complaints and claims. Techniques are thus needed to characterise the modification of quality in terms of improved target properties of TMT during industrial production, and of TMT products that have been in service for an arbitrary time. In this study, we aimed to utilise dynamic vapor sorption (DVS) for this purpose. Norway spruce (Picea abies) and European beech (Fagus sylvatica) samples were thermally modified at different temperatures according to different heat treatment techniques: (1) the Silvapro process based on an initial vacuum; (2) an air heat treatment, whereby samples were wrapped in aluminium foil; (3) thermal modification of wood samples in the ambient atmosphere in a laboratory oven. Wood samples from closed processes were analysed for validation. TMT was characterised with respect to mass loss, colour and density. Mass loss of wood due to modification (MLTM) was correlated with factors derived from DVS analysis. The present DVS measurements suggest that the equilibrium wood moisture content (EMC95% RH), the time to reach 10% wood moisture content (t10% MC), and the elongation factor, c, derived from a logarithmic function, can serve as alternative parameters to characterise the quality of several thermal modification processes. Further studies are recommended using other wood species, different modification processes and further parameters gained from DVS measurements to understand the robustness and the predictive power of the applied technique
Ključne besede: thermal modification, quality control, dynamic vapour sorption, wood, moisture content
Objavljeno v DiRROS: 31.08.2023; Ogledov: 308; Prenosov: 153
Celotno besedilo (1,91 MB)
Gradivo ima več datotek! Več...

Povzetek: Mortar specimens made from four different types of cement, CEM I, CEM II, CEM III, and CEM IV, were prepared and pore solutions extracted. Three different types of exposure were studied: noncarbonated without chlorides, noncarbonated with chlorides, and carbonated with chlorides. Various electrochemical methods (linear polarization, potentiodynamic polarization measurements) were implemented to characterize the processes of corrosion on steel in these solutions. The type and extent of corrosion products were evaluated by means of various spectroscopic techniques. Specific differences in the type and extent of corrosion damage were determined and compared for each of the extracted pore solutions from the different blended cements. An attempt was made to classify these differences in comparison with the reference cement (CEM I) and in relation to the different types of exposure.
Ključne besede: corrosion, steel in pore water, blended cements, Raman Spectroscopy
Objavljeno v DiRROS: 22.08.2023; Ogledov: 274; Prenosov: 129
Celotno besedilo (1,25 MB)
Gradivo ima več datotek! Več...