1. |
2. Evaluation of two-dimensional dose distributions for pre-treatment patient-specific IMRT dosimetryĐeni Smilović Radojčić, David Rajlić, Božidar Casar, Manda Švabić Kolacio, Nevena Obajdin, Dario Faj, Slaven Jurković, 2018, izvirni znanstveni članek Povzetek: The accuracy of dose calculation is crucial for success of the radiotherapy treatment. One of the methods that represent the current standard for patient-specific dosimetry is the evaluation of dose distributions measured with an ionization chamber array inside a homogeneous phantom using gamma method. Nevertheless, this method does not replicate the realistic conditions present when a patient is undergoing therapy. Therefore, to more accurately evaluate the treatment planning system (TPS) capabilities, gamma passing rates were examined for beams of different complexity passing through inhomogeneous phantoms. Materials and methods The research was performed using Siemens Oncor Expression linear accelerator, Siemens Somatom Open CT simulator and Elekta Monaco TPS. A 2D detector array was used to evaluate dose distribution accuracy in homogeneous, semi-anthropomorphic and anthropomorphic phantoms. Validation was based on gamma analysis with 3%/3mm and 2%/2mm criteria, respectively. Results Passing rates of the complex dose distributions degrade depending on the thickness of non-water equivalent material. They also depend on dose reporting mode used. It is observed that the passing rate decreases with plan complexity. Comparison of the data for all set-ups of semi-anthropomorphic and anthropomorphic phantoms shows that passing rates are higher in the anthropomorphic phantom. Conclusions Presented results raise a question of possible limits of dose distribution verification in assessment of plan delivery quality. Consequently, good results obtained using standard patient specific dosimetry methodology do not guarantee the accuracy of delivered dose distribution in real clinical cases Ključne besede: IMRT, 2D dose verification, gamma method, antropomorphic phantom Objavljeno v DiRROS: 10.06.2024; Ogledov: 206; Prenosov: 104
Celotno besedilo (786,37 KB) Gradivo ima več datotek! Več... |
3. Experimental carbonation study for durability assessment of novel cementitious materialsSebastijan Robič, Aljoša Šajna, Lucija Hanžič, Alisa Machner, Marie Helene Bjørndal, Klaartje De Weerdt, Yushan Gu, Benoit Bary, Rosamaria Lample, 2021, objavljeni znanstveni prispevek na konferenci Povzetek: The design process of concrete structures is carried out using standards and guidelines, while the durability predictions of concrete structures is supported only with exposure classes and experience-based requirements. To improve durability predictions of the carbonation resistance of concrete, a numerical model is being developed within the Horizon 2020 project EnDurCrete, coupling the rate of carbonation, and the drying rate. To verify the numerical model, an accelerated carbonation study was carried out. Experiments were conducted on mortars incorporating a novel CEM II/C (S-LL) cement, developed within the EnDurCrete project, and a commercially available reference cementCEM II/A-S. EnDurCrete mortars (EnM) and reference mortars (RefM) were prepared with water-cement ratios of 0.6 and 0.5 (denoted with label extensions -06 and -05). Visual assessments and thermogravimetric analysis (TGA) were used to measure the carbonation rates, which were found to be ~1.0 mm day-0.5 in EnM-06 and ~0.6 mm day-0.5 in RefM-06, while in EnM-05 and RefM-05 the values were ~0.7 and ~0.2 mm day-0.5 respectively. Additionally, TGA shows that the initial portlandite (CH) content is ~1.5 wt% in EnM-06 as opposed to ~3.0 wt% in RefM-06. The difference in the initial CH content in the two hydrated binders might explain the difference in their carbonation rate. During the moisture transport experiments a gravimetric method was used to determine mass changes as specimens underwent drying and resaturation with and without CO2 present. The drying led to a decrease in mass, but in the presence of CO2 this mass loss was compensated by the mass gain due to uptake of CO2 during carbonation. The resaturation experiments indicate an increase in the suction porosity in the carbonated samples compared to the non-carbonated samples. Ključne besede: concrete, absorption of water, carbonation, durability assessment, model verification Objavljeno v DiRROS: 25.01.2024; Ogledov: 401; Prenosov: 276
Celotno besedilo (9,29 MB) Gradivo ima več datotek! Več... |
4. Experimental carbonation study for a durability assessment of novel cementitious materialsLucija Hanžič, Sebastijan Robič, Alisa Machner, Marie Helene Bjørndal, Klaartje De Weerdt, Yushan Gu, Benoit Bary, Rosa Maria Lample Carreras, Aljoša Šajna, 2021, izvirni znanstveni članek Povzetek: Durability predictions of concrete structures are derived from experience-based require- ments and descriptive exposure classes. To support durability predictions, a numerical model related to the carbonation resistance of concrete was developed. The model couples the rate of carbonation with the drying rate. This paper presents the accelerated carbonation and moisture transport exper- iments performed to calibrate and verify the numerical model. They were conducted on mortars with a water-cement ratio of either 0.6 or 0.5, incorporating either a novel cement CEM II/C (S-LL) (EnM group) or commercially available CEM II/A-S cement (RefM group). The carbonation rate was determined by visual assessment and thermogravimetric analysis (TGA). Moisture transport experi- ments, consisting of drying and resaturation, utilized the gravimetric method. Higher carbonation rates expressed in mm/day−0.5 were found in the EnM group than in the RefM group. However, the TGA showed that the initial portlandite (CH) content was lower in the EnM than in the RefM, which could explain the difference in carbonation rates. The resaturation experiments indicate an increase in the suction porosity in the carbonated specimens compared to the non-carbonated specimens. The study concludes that low clinker content causes lower resistance to carbonation, since less CH is available in the surface layers; thus, the carbonation front progresses more rapidly towards the core. Ključne besede: mortar, absorption of water, carbonation, durability assessment, model verification Objavljeno v DiRROS: 05.07.2023; Ogledov: 484; Prenosov: 278
Celotno besedilo (4,84 MB) Gradivo ima več datotek! Več... |
5. Leaching and geochemical modelling of an electric arc furnace (EAF) and ladle slag heapMojca Loncnar, Ana Mladenovič, Vesna Zalar Serjun, Marija Zupančič, Hans A. van der Sloot, 2022, izvirni znanstveni članek Povzetek: Old metallurgical dumps across Europe represent a loss of valuable land and a potential threat to the environment, especially to groundwater (GW). The Javornik electric arc furnace (EAF) and ladle slag heap, situated in Slovenia, was investigated in this study. The environmental impact of the slag heap was evaluated by combining leaching characterization tests of landfill samples and geochemical modelling. It was shown that throughout the landfill the same minerals and sorptive phases control the leaching of elements of potential concern, despite variations in chemical composi- tion. Although carbonation of the disposed steel slags occurred (molar ratio CO3/(Ca+Mg) = 0.53) relative to fresh slag, it had a limited effect on the leaching behaviour of elements of potential concern. The leaching from the slag heaps had also a limited effect on the quality of the GW. A site-specific case, however, was that leachates from the slag heap were strongly diluted, since a rapid flow of GW fed from the nearby Sava River was observed in the landfill area. The sampling and testing approach applied provides a basis for assessing the long-term impact of release and is a good starting point for evaluating future management options, including beneficial uses for this type of slag. Ključne besede: EAF slag, field verification, geochemical modelling, ladle slag, leaching, release prediction, steel slag heap Objavljeno v DiRROS: 28.04.2023; Ogledov: 645; Prenosov: 293
Celotno besedilo (4,37 MB) Gradivo ima več datotek! Več... |
6. Validation and verification of examination procedures in medical laboratories : opinion of the EFLM Working Group Accreditation and ISO/CEN standards (WG-A/ISO) on dealing with ISO 15189:2012 demands for method verification and validationRoseri Roelofsen-de Beer, Jos Wielders, Guilaine Boursier, Tatjana Vodnik, Florent Vanstapel, Wim Huisman, Ines Vukasović, Michel Vaubourdolle, Çiğdem Sönmez, Solveig Linko, Pika Meško-Brguljan, 2020, izvirni znanstveni članek Povzetek: This paper reflects the opinion of the European Federation of Clinical Chemistry and Laboratory Medicine (EFLM) Working Group Accreditation and ISO/CEN standards (WG-A/ISO). It aims to provide guidance for drawing up local/national documents about validation and verification of laboratory methods. We demonstrate how risk evaluation can be used to optimize laboratory policies to meet intended use requirements as well as requirements of standards. This is translated in a number of recommendations on how to introduce risk evaluation in various stages of the implementation of new methods ultimately covering the whole process cycle. Ključne besede: opinion paper, EFLM, ISO 15189:2012, validation, verification Objavljeno v DiRROS: 10.08.2020; Ogledov: 1611; Prenosov: 483
Povezava na datoteko |