1781. High temperature oxidation of EN AW 7075 aluminium alloyNejc Velikajne, Tilen Balaško, Jaka Burja, Matjaž Godec, Irena Paulin, 2024, published scientific conference contribution Abstract: Aluminium alloys are highly valued for their exceptional strength-to-weight ratio, making them a preferred choice in structural applications. Among these alloys, EN AW 7075 stands out for its superior mechanical properties, finding widespread use in industries such as aerospace, mechanical engineering, and sports equipment. This study investigates the high-temperature oxidation behavior of EN AW 7075 alloy. The gathered results can provide valuable insights into the behavior of the mentioned alloy during the selective laser melting (SLM) process. These results can contribute to a better understanding of how the alloy responds to specific conditions and parameters. SLM is an additive manufacturing technique. The process involves the sequential steps of preheating, melting, and rapid cooling of metal powder. To minimize the influence of oxygen, the build chamber is filled with inert gas. A protective argon atmosphere is continuously maintained. However, despite these precautions, oxidation can still occur, leading to potential issues in the final product. Hence, we examined the oxidation kinetics of the EN AW 7075 alloy in an oxygen atmosphere in the temperature range of 300-500 °C. The findings of this investigation significantly contribute to an understanding of the behavior of the alloy during high-temperature oxidation, particularly for ongoing studies focused on processing Al-Zn-Mg-Cu alloys using the selective laser melting technique. Thermogravimetry was employed to analyze the oxidizing behavior, with three samples subjected to a 6-hour exposure in an oxidizing atmosphere at temperatures of 300, 400, and 500 °C. Surprisingly, no oxidation occurred, as indicated by the negligible and negative changes in mass observed across all samples. Keywords: EN AW 7075, high-temperature oxidation, oxide film, selective laser melting Published in DiRROS: 28.02.2024; Views: 396; Downloads: 182
Full text (897,18 KB) This document has many files! More... |
1782. Quality checking of polymer modified bitumens in SloveniaMarjan Tušar, Lidija Ržek, Mojca Ravnikar Turk, 2021, published scientific conference contribution Abstract: For many years the properties of bitumen have been determined based on mechanical tests as needle penetration, Ring&Ball and Fraass fracture temperature. For elastomer (styrene-butadiene-styrene) polymer modified bitumens these tests are not sufficient to show the important differences in bitumens. Elastic recovery and cohesion provide better insight, but rheological properties cannot be adequately described with conventional test. The requirements of the polymer modified bitumens (PmB) in Europe were defined in EN14023 in 2010 [1]. Since then several new tests were introduced in the research field and their procedures improved. In the European Standards Committee (CEN) TC 336, there is on-going work to develop performance related specifications. New laboratory test methods from American standards were adapted and transformed into EN standards (bitumen laboratory aging methods and rheological tests). These test methods are not yet employed in the cur-rent PmB European standard, however, the draft prEN 14023, April 2020 [2] suggests these new tests. In the recent years at ZAG Laboratory for asphalts and bitumen-based products long-term aging of bitumen by pressure aging vessel (PAV) and rheological tests were introduced. Traditional bitumen test methods are performed together with new rheological testse.g. Dynamic Shear Rheometer (DSR) testing, to characterize complex modulus and phase angle, and Multiple Stress Creep Recovery Test (MSCRT) in order to develop a preliminary data base on PmB’s, which are frequently used in Slovenia. The paper presents the current requirements for PmB’s in Slovenia and test results on PmB 45/80-65, original, laboratory aged and extracted from produced asphalt mixtures. Keywords: polymer modified bitumen, recovered bitumen, laboratory ageing, dynamic shear rheometer, multiple stress creep recovery test Published in DiRROS: 28.02.2024; Views: 364; Downloads: 244
Full text (703,78 KB) This document has many files! More... |
1783. Overview of global long-distance road Transportation of industrial roundwoodKärhä Kalle, Milla Seuri, Patricio Miguel Mac Donagh, Mauricio Acuna, Christian Kanzian, Vladimir Petković, Robert Renato Cesar Gonçalves, Costa Luis Henrique Suppi, da Cruz Rodrigo Coelho, Tihomir Krumov, Matevž Triplat, 2024, review article Abstract: The aim of the study was to provide a comprehensive overview of global long-distance road transportation of industrial roundwood. The study focused on the maximum gross vehicle weight (GVW) limits allowed with different timber truck configurations, typical payloads in timber trucking, the road transportation share of the total industrial roundwood longdistance transportation volume, and the average long-distance transportation distances and costs of industrial roundwood. The study was carried out as a questionnaire survey. The questionnaire was sent to timber transportation logistics experts and research scientists in the 30 countries with the largest industrial roundwood removals in Europe, as well as selected major forestry countries in the world (Argentina, Australia, Brazil, Canada, Chile, China, Japan, New Zealand, South Africa, Türkiye, the United States of America and Uruguay) in February 2022, and closed in May 2022. A total of 31 countries took part in the survey. The survey illustrated that timber trucking was the main long-distance transportation method of industrial roundwood in almost every country surveyed. Road transportation averaged 89% of the total industrial roundwood long-distance transportation volume. Timber truck configurations of 4 to 9 axles with GVW limits of around 30 tonnes to over 70 tonnes were most commonly used. The results indicated that higher GVW limits allowed significantly higher payloads in timber trucking, with the lowest payloads at less than 25 tonnes, and the highest payloads more than 45 tonnes. The average road transportation distance with industrial roundwood was 128 km, and the average long-distance transportation cost in timber trucking was €11.1 per tonne of timber transported. In the entire survey material, there was a direct relationship between transportation distance and transportation costs and an inverse relationship between maximum GVW limits and transportation costs. Consequently, in order to reduce transportation costs, it is essential to maximise payloads (within legal limits) and minimise haul distances. Several measures to increase cost- and energy-efficiency, and to reduce greenhouse gas emissions in road transportation logistics, are discussed in the paper. On the basis of the survey, it is recommended that upto-date statistical data and novel research studies on the long-distance transportation of industrial roundwood be conducted in some countries in the future. Keywords: timber logistics, timber hauling, timber trucking, gross vehicle weight, payload, transportation distance, transportation cost, cost efficiency, limit payload Published in DiRROS: 28.02.2024; Views: 377; Downloads: 204
Full text (1,77 MB) This document has many files! More... |
1784. Enhancing ductility of hot-work tool steel through isothermal bainitic transformationAnže Bajželj, Aleš Nagode, Tilen Balaško, Barbara Šetina, Jaka Burja, 2024, published scientific conference contribution Abstract: Hot-work tool steels are extensively used in industrial applications that require high resistance to mechanical and chemical degradation at elevated temperatures. To meet these requirements, hot-work tool steels must exhibit good mechanical properties, including high tensile strength, hardness, wear resistance, and tempering resistance, as well as high thermal conductivity and ductility. This study investigates the ductility of the hot-work tool steel HTCS-130, which suffers from low ductility due to the presence of stable molybdenum-tungsten carbides (M6C) on the prior austenite crystal grain boundaries. Increasing austenitisation temperatures or prolonging the dwelling time at temperature can promote intensive migration of grain boundaries, leading to negative effects on the mechanical properties of the steel. To address this issue, isothermal transformation in the bainitic area between 350 and 500 °C was performed. Isothermal transformation at around 350 °C leads to the formation of lower bainite, which has similar hardness to tempered martensite. As the temperature of isothermal transformation increases, the hardness of the material decreases, due to the formation of upper bainite. The hardness analysis was measured using the Vickers method, the impact toughness of the steel samples was measured using a Charpy test with V-notched samples. The microstructure characterization was performed using optical and scanning electron microscopy. The improvement of ductility can be achieved by controlling the isothermal transformation of bainite and adjusting the heat treatment conHot-work tool steels are extensively used in industrial applications that require high resistance to mechanical and chemical degradation at elevated temperatures. To meet these requirements, hot-work tool steels must exhibit good mechanical properties, including high tensile strength, hardness, wear resistance, and tempering resistance, as well as high thermal conductivity and ductility. This study investigates the ductility of the hot-work tool steel HTCS-130, which suffers from low ductility due to the presence of stable molybdenum-tungsten carbides (M6C) on the prior austenite crystal grain boundaries. Increasing austenitisation temperatures or prolonging the dwelling time at temperature can promote intensive migration of grain boundaries, leading to negative effects on the mechanical properties of the steel. To address this issue, isothermal transformation in the bainitic area between 350 and 500 °C was performed. Isothermal transformation at around 350 °C leads to the formation of lower bainite, which has similar hardness to tempered martensite. As the temperature of isothermal transformation increases, the hardness of the material decreases, due to the formation of upper bainite. The hardness analysis was measured using the Vickers method, the impact toughness of the steel samples was measured using a Charpy test with V-notched samples. The microstructure characterization was performed using optical and scanning electron microscopy. The improvement of ductility can be achieved by controlling the isothermal transformation of bainite and adjusting the heat treatment conditions. These findings provide useful insights into the design and optimization of heat treatment processes for hot-work tool steels.ditions. These findings provide useful insights into the design and optimization of heat treatment processes for hot-work tool steels. Keywords: hot-work tool steel, austempering, bainitic transformation, ductility, dilatometry Published in DiRROS: 28.02.2024; Views: 406; Downloads: 165
Full text (1,02 MB) This document has many files! More... |
1785. The genus Fomitopsis (Polyporales, Basidiomycota) reconsideredViacheslav Spirin, K. Runnel, J. Vlasák, I. Viner, M.D. Barrett, L. Ryvarden, Annarosa Bernicchia, B. Rivoire, A.M. Ainsworth, Tine Grebenc, 2024, original scientific article Abstract: Based on seven- and three-gene datasets, we discuss four alternative approaches for a reclassification of Fomitopsidaceae (Polyporales, Basidiomycota). After taking into account morphological diversity in the family, we argue in favour of distinguishing three genera only, viz. Anthoporia, Antrodia and Fomitopsis. Fomitopsis becomes a large genus with 128 accepted species, containing almost all former Fomitopsis spp. and most species formerly placed in Antrodia, Daedalea and Laccocephalum. Genera Buglossoporus, Cartilosoma, Daedalea, Melanoporia, Neolentiporus, alongside twenty others, are treated as synonyms of Fomitopsis. This generic scheme allows for morphologically distinct genera in Fomitopsidaceae, unlike other schemes we considered. We provide arguments for retaining Fomitopsis and suppressing earlier (Daedalea, Caloporus) or simultaneously published generic names (Piptoporus) considered here as its synonyms. Taxonomy of nine species complexes in the genus is revised based on ITS, ITS + TEF1, ITS + TEF1 + RPB1 and ITS + TEF1 + RPB2 datasets. In total, 17 species are described as new to science, 26 older species are reinstated and 26 currently accepted species names are relegated to synonymy. A condensed identification key for all accepted species in the genus is provided. Keywords: brown-rot fungi, new taxa, phylogeny, polypores, taxonomy Published in DiRROS: 28.02.2024; Views: 543; Downloads: 340
Full text (12,89 MB) This document has many files! More... |
1786. Effect of heat treatment on thermal conductivity of additively manufactured AISI H13 tool steelSamo Tome, Blaž Karpe, Irena Paulin, Matjaž Godec, 2024, published scientific conference contribution Abstract: AISI H13 is commonly used for tooling, where higher wear resistance, thermal fatigue resistance, or hot toughness is required. Such examples include forging dies, plastic molds, hot shear blades, high-pressure die casting, and extrusion dies. Thus, thermal conductivity is one of the most important factors for hot work tools. Typically, the work cycle of a hot work tool designed for forging consists of four main phases: the forging stroke, with which the die imparts its shape onto the part, a brief pause while the die is reset to its original position, a lubrication phase, and a post lubrication dwell phase. During the forging phase, a significant amount of heat is transferred to the die while it is in contact with the part. This heat must then be dispelled for the part to return to a working temperature. While somewhat different, other hot work processes mentioned above are similar in that the hot work tool gets heated to a high temperature due to the contact with the object of deformation. The process of additive manufacturing (AM) promises better, more efficient tool production with features like conforming cooling channels, which would reduce the thermal fatigue of tools, prolonging tool life. However, the powder bed fusion (PBF) method creates a columnar microstructure, which has a detrimental effect on the thermal conductivity of H13 tool steel. Our investigation focused on the beneficial effect of heat treatment, specifically annealing at different temperatures, on the thermal conductivity of AM-produced H13 parts. Keywords: SLM, thermal conductivity, tool steel, heat treatment Published in DiRROS: 28.02.2024; Views: 344; Downloads: 173
Full text (655,96 KB) This document has many files! More... |
1787. Extreme environments simplify reassembly of communities of arbuscular mycorrhizal fungiNataša Šibanc, Dave R. Clark, Thorunn Helgason, Alex J. Dumbrell, Irena Maček, 2024, original scientific article Abstract: The ecological impacts of long-term (press) disturbance on mechanisms regulating the relative abundance (i.e., commonness or rarity) and temporal dynamics of species within a community remain largely unknown. This is particularly true for the functionally important arbuscular mycorrhizal (AM) fungi; obligate plant-root endosymbionts that colonize more than two-thirds of terrestrial plant species. Here, we use high-resolution amplicon sequencing to examine how AM fungal communities in a specific extreme ecosystem—mofettes or natural CO2 springs caused by geological CO2 exhalations—are affected by long-term stress. We found that in mofettes, specific and temporally stable communities form as a subset of the local metacommunity. These communities are less diverse and dominated by adapted, “stress tolerant” taxa. Those taxa are rare in control locations and more benign environments worldwide, but show a stable temporal pattern in the extreme sites, consistently dominating the communities in grassland mofettes. This pattern of lower diversity and high dominance of specific taxa has been confirmed as relatively stable over several sampling years and is independently observed across multiple geographic locations (mofettes in different countries). This study implies that the response of soil microbial community composition to long-term stress is relatively predictable, which can also reflect the community response to other anthropogenic stressors (e.g., heavy metal pollution or land use change). Moreover, as AM fungi are functionally differentiated, with different taxa providing different benefits to host plants, changes in community structure in response to long-term environmental change have the potential to impact terrestrial plant communities and their productivity Keywords: arbuscular mycorrhiza, elevated CO2, long-term experiments, soil biodiversity, soil hypoxia, next-generation sequencing, NGS Published in DiRROS: 28.02.2024; Views: 414; Downloads: 216
Full text (1,45 MB) This document has many files! More... |
1788. Development of the recycling procedure for rapid antigen testsRebeka Rudolf, Darja Feizpour, Žiga Jelen, Peter Majerič, Tilen Švarc, Matej Zadravec, Timi Gomboc, Aleksandra Kocijan, 2024, original scientific article Keywords: rapid antigen tests, recycling, characterization, nanogold, plastic Published in DiRROS: 28.02.2024; Views: 401; Downloads: 163
Full text (1,74 MB) This document has many files! More... |
1789. A numerical study of gas focused non-Newtonian micro-jetsRizwan Zahoor, Saša Bajt, Božidar Šarler, 2024, original scientific article Keywords: serial crystallography, micro jets, multiphase flow, fluid rheology, non-Newtonian fluid, flow focusing Published in DiRROS: 28.02.2024; Views: 367; Downloads: 187
Full text (11,78 MB) This document has many files! More... |
1790. A hybrid radial basis function-finite difference method for modelling two-dimensional thermo-elasto-plasticity : Application to cooling of hot-rolled steel bars on a cooling bedGašper Vuga, Boštjan Mavrič, Umut Hanoglu, Božidar Šarler, 2024, original scientific article Abstract: This paper represents Part 2 of the parallel paper Part 1, where the strong form hybrid RBF-FD method was developed for solving thermo-elasto-plastic problems. It addresses the industrial application of this novel meshless method to steel bars cooling on a cooling bed (CB) where the formation of residual stress is of primary interest. The study investigates the impact of the distance between the bars and the distance to the heat shield above the CB on radiative heat fluxes and, consequently, on thermo-mechanical response. The thermal model is solved on bars cross-section with a RBF-FD method where augmented polyharmonic splines are used for the local approximation. View factors, computed with a Monte-Carlo method, are included in radiative heat fluxes. The thermal solution is incrementally applied on a mechanical model that assumes a generalised plane strain state and captures bars bending. The study employs a hybrid RBF-FD method to resolve a nonlinear discontinuous mechanical problem successfully. The simulation of the process shows how different process parameters influence the thermo-mechanical response of the bars. Keywords: steel bars, cooling bed, thermo-mechanical modelling, hybrid radial basis function, generated finite differences, residual stresses Published in DiRROS: 28.02.2024; Views: 323; Downloads: 190
Full text (8,55 MB) This document has many files! More... |