41. Effect of deep cryogenic treatment on corrosion properties of various high-speed steelsJure Voglar, Živa Novak, Patricia Jovičević Klug, Bojan Podgornik, Tadeja Kosec, 2021, original scientific article Abstract: The aim of the study was to evaluate the corrosion properties of three different grades of high-speed steel following a heat treatment procedure involving deep cryogenic treatment after quenching and to investigate how these properties are connected to the microstructure and hard- ness of the material. The hardness of steels was measured, and microstructural properties were determined through observation of the metallographically prepared steels using scanning electron microscopy. These studies were complemented corrosion evaluation by the use of corrosion potential measurement and linear polarization measurement of steels in a sodium tetraborate buffer at pH 10. The results showed that the deep cryogenic procedure of high-speed steel changed the microstructure and consequently affected the hardness of the investigated steels to different extents, depending on their chemical composition. Corrosion studies have confirmed that some high-speed steels have improved corrosion properties after deep cryogenic treatment. The most important improvement in corrosion resistance was observed for deep cryogenically treated high-speed steel EN 1.3395 (M3:2) by 31% when hardened to high hardness values and by 116% under lower hardness conditions. The test procedure for differentiating corrosion properties of differently heat-treated tool steels was established alongside the investigation.
Keywords: deep cryogenic treatment, corrosion, microstructure, hardness
Published in DiRROS: 01.08.2023; Views: 276; Downloads: 142
 Full text (5,82 MB)
This document has many files! More... |
42. Modelling the electrochemical transients during repassivation under open-circuit conditions in a neutral solutionBojan Zajec, Tadeja Kosec, Andraž Legat, 2022, original scientific article Abstract: The responses of the current and the coupled potential to rapid depassivation have been studied on a three-electrode system under open-circuit conditions. Passivated AISI 304 stainless steel in low- and high-conductivity solutions of NaSO has been depassivated with a single, rapid scratch over the small fraction of surface of the working electrode (WE). Single- and dual-WE configurations have been implemented. Once the surface is scratched, the current and potential transients exhibit a delayed maximum and minimum, respectively, in contrast to the outcome of more common potentiostatic scratching experiments. A simple model based on the equivalent circuit has been developed to predict the observed transients and provides clear relations between the features of the transient and the parameters of the electrolyte and the electrodes. The interfacial capacitance of the electrodes’ passive surfaces proves crucial for the shapes of the observed potential and current transients. It is shown that this capacitance temporarily provides the majority of the charge for repassivation under open-circuit conditions. Possible sources of specific discrepancies between the model and the measured transients are indicated.
Keywords: repassivation, open circuit conditions, transient, modelling, interfacial capacitance
Published in DiRROS: 21.06.2023; Views: 324; Downloads: 150
Full text (1,75 MB)
This document has many files! More... |
43. Effect of surface machining on the environmentally-assisted cracking of Alloy 182 and 316L stainless steel in light water reactor environments : results of the collaborative project MEACTOSMariia Zimina, Stefan Ritter, Bojan Zajec, Marc Vankeerberghen, Liberato Volpe, Anna Hojna, Rik-Wouter Bosch, Fabio Scenini, Zaiqing Que, Alberto Sáez-Maderuelo, P. Jill Meadows, Michael Grimm, Matthias Herbst, Andraž Legat, Agostino Maurotto, Radek Novotny, Karl-Heinz Seifert, 2023, original scientific article Abstract: The main objective of the EU-funded project mitigating environmentally-assisted cracking through optimisation of surface condition (MEACTOS) was to gain knowledge on the ability of different surface machining procedures to mitigate environmentally-assisted cracking (EAC) in typical light water reactor structural materials and environments. Surfaces of cold-worked (CW) type 316L austenitic stainless steel and nickel-based weld metal Alloy 182 flat tapered tensile specimens were machined using different processes. EAC initiation susceptibility of these specimens was evaluated using constant extension rate tensile (CERT) tests under simulated boiling water reactor (BWR) and pressurized water reactor (PWR) conditions and assessed using constant load experiments. More than a hundred tests were performed covering about 10 years of autoclave testing time. Only minor or no measurable improvements in EAC initiation susceptibility as a function of surface treatments (grinding or advanced machining) compared to the standard industrial face milling were demonstrated. In most cases, the stress thresholds for EAC initiation determined in constant load tests confirmed the trend obtained from CERT tests. This paper summarises the most important results and conclusions concerning the EAC initiation behaviour for the CW 316L and Alloy 182 under reducing PWR and oxidizing BWR conditions.
Keywords: crack initiation, environmentally-assisted cracking, Alloy 182, AISI 304 stainless steel, surface treatment, light water reactor, open access
Published in DiRROS: 30.05.2023; Views: 328; Downloads: 188
Full text (16,31 MB)
This document has many files! More... |
44. Differences between 3-D printed and traditionally milled CoCr dental alloy from casted block in oral environmentMirjam Bajt Leban, Matej Kurnik, Igor Kopač, Matic Klug Jovičević, Bojan Podgornik, Tadeja Kosec, 2023, original scientific article Abstract: The aim of this study was to compare corrosion resistance and ion release in CoCr dental alloys with identical chemical compositions produced using different technologies (SLM – selective laser melting and milling from cast blocks) and heat treatment (SLM parts only). The corrosion properties were tested in artificial saliva, artificial saliva with fluoride ions, and artificial saliva with added lactic acid to simulate inflammations. The study included electrochemical tests, microstructural investigation and ion release tests in the three different environments for a total of 42 days. The best performance of CoCr as a result of potentiodynamic polarization was observed in the artificial saliva with added lactic acid, which is in contradiction with the highest ion release measured from all the materials tested and electrochemical impedance spectroscopy that showed a deterioration of the passive layer in an acidic environment. Microstructural investigation revealed that different phases precipitated by heat treatment trigger increased release of Mo and W ions. The printing method does not raise critically ion release from CoCr alloy, while the state of the surface greatly impacts the extent of the ion release. This study demonstrates the importance of an interdisciplinary approach to the study of corrosion and biocompatibility in dental alloys.
Keywords: CoCr dental alloy, selective laser melting, corrosion, ion release, artificial saliva
Published in DiRROS: 29.05.2023; Views: 339; Downloads: 287
Full text (9,28 MB)
This document has many files! More... |
45. Influence of the deep cryogenic treatment on AISI 52100 and AISI D3 steelʼs corrosion resistancePatricia Jovičević Klug, Tjaša Kranjec, Matic Klug Jovičević, Tadeja Kosec, Bojan Podgornik, 2021, original scientific article Abstract: The effect of deep cryogenic treatment (DCT) on corrosion resistance of steels AISI 52100 and AISI D3 is investigated and compared with conventional heat-treated counterparts. DCTʼs influence on microstructural changes is subsequently correlated to the corrosion resistance. DCT is confirmed to reduce the formation of corrosion products on steelsʼ surface, retard the corrosion products development and propagation. DCT reduces surface cracking, which is considered to be related to modified residual stress state of the material. DCTʼs influence on each steel results from the altered microstructure and alloying element concentration that depends on steel matrix and type. This study presents DCT as an effective method for corrosion resistance alteration of steels.
Keywords: steel, deep cryogenic treatment, corrosion, Raman, open access
Published in DiRROS: 19.05.2023; Views: 303; Downloads: 221
Full text (3,13 MB)
This document has many files! More... |
46. Effect of laser texturing pattern on Ti6Al4Vtribocorrosion in a physiological solutionMarjetka Conradi, Tadeja Kosec, Bojan Podgornik, Aleksandra Kocijan, Janez Kovač, Damjan Klobčar, 2022, original scientific article Abstract: Laser texturing is a process that alters a material’s surface properties by modifying its morphology, which can improve properties like adherence, wettability, thermal and electrical conductivity and friction. Here, the effect of laser texturing was studied on an alpha-beta titanium alloy (Ti6Al4V) biomedical material. Two types of patterned surfaces, cross-hatch with varying scan-line separations, Dx = 100, 180 and 280 μm and dimples of 200 μm size, were prepared on the surface of alpha-beta titanium alloy by laser technology. Prepared samples were characterised for their surface properties, such as corrosion, wear-induced corrosion, friction and wettability. Electrochemical and tribocorrosion properties in a physiological solution were studied on the samples with different texture densities of cross-hatch pattern and dimples and compared to the as-received alpha-beta titanium alloy surface. Corrosion rate decreased for laser-textured samples, especially for cross-hatch texture (down to 1 μm/year for Dx = 180 μm) when compared to the as-received alpha-beta titanium alloy surface due to the changed laser-induced surface film and wetting properties. Friction coefficient slightly decreased for all laser-textured surfaces, most noticeably for cross-hatch patterns, from 0.38 (as-received) down to 0.34 (Dx = 180 and 280 μm). The main contribution to total wear in physiological solution increased due to the mechanical wear, which is governed by the removal of the surface oxide layer induced by laser texturing.
Keywords: TiAIV, laser texturing, tribocorrosion, open access
Published in DiRROS: 17.05.2023; Views: 294; Downloads: 119
Full text (2,19 MB)
This document has many files! More... |
47. Investigation of surface treatment effects on the environmentally-assisted cracking behaviour of Alloy 182 in boiling water reactor environmentZaiqing Que, Bojan Zajec, Stefan Ritter, Tommi Seppänen, Timo Saario, Aki Toivonen, Aleksandra Treichel, Valentin Lautaru, Fabio Scenini, 2022, original scientific article Abstract: Surface treatments of primary circuit components in light water reactors are regarded as possible ways to mitigate environmentally-assisted cracking (EAC). To date, it is not fully conclusive which surface condition is suitable to reduce the EAC initiation susceptibility. Constant extension rate tensile (CERT) tests were performed by several labs using flat tapered tensile specimens with different surface conditions (ground, industrial face milled, advanced face milled and shot peened), exposed to a boiling water reactor normal water chemistry environment at 288°C. Despite some scatter in the results, the CERT tests revealed that the EAC initiation susceptibility seems lowest for the advanced face milled surface and highest for the shot peened surface. However, it must be emphasised that the differences were moderate and that the surprising behaviour of the shot peened surface can be explained. The mechanical grinding of the surface did not significantly retard EAC initiation compared to industrial face milling.
Keywords: crack initiation, environmentally-assisted cracking, Alloy 182, surface machining, boiling water reactor, open access
Published in DiRROS: 05.05.2023; Views: 356; Downloads: 149
Full text (4,12 MB)
This document has many files! More... |
48. |
49. |
50. How well did the healthcare system respond to the healthcare needs of older people with and without dementia during the COVID-19 pandemic : the perception of healthcare providers and older people from the SI4CARE Project in the ADRION RegionStella Fragkiadaki, Dionysia Kontaxopolou, Darja Šemrov, Simon Colnar, Mitja Luštrek, Bojan Blažica, Vlado Dimovski, Sokratis G. Papageorgiou, 2023, original scientific article Abstract: One major challenge during the COVID-19 pandemic was the limited accessibility to healthcare facilities, especially for the older population. The aim of the current study was the exploration of the extent to which the healthcare systems responded to the healthcare needs of the older people with or without cognitive impairment and their caregivers in the Adrion/Ionian region. Data were collected through e-questionnaires regarding the adequacy of the healthcare system and were anonymously administered to older individuals and stakeholder providers in the following countries: Slovenia, Italy (Calabria), Croatia, Bosnia and Herzegovina, Greece, Montenegro, and Serbia. Overall, 722 older people and 267 healthcare stakeholders participated in the study. During the COVID-19 pandemic, both healthcare stakeholders and the older population claimed that the healthcare needs of the older people and their caregivers increased dramatically in all countries, especially in Italy (Calabria), Croatia and BiH. According to our results, countries from the Adrion/Ionian regions faced significant challenges to adjust to the special needs of the older people during the COVID-19 pandemic, which was possibly due to limited accessibility opportunities to healthcare facilities. These results highlight the need for the development of alternative ways of providing medical assistance and supervision when in-person care is not possible.
Keywords: healthcare system responses, COVID-19 pandemic, older people, cognitive impairment, dementia, caregivers, telemedicine, healthcare challenges, accessibility, Slovenia, Italy, Serbia, Croatia, Bosnia and Herzegovina, Greece, Montenegro
Published in DiRROS: 01.02.2023; Views: 583; Downloads: 253
Full text (412,07 KB)
This document has many files! More... |
