1. Risk based life-cycle planning for flood-resilient critical infrastructureSandra Škarić Palić, I. Stipanovic, E. Ganic, Mirko Kosič, Andrej Anžlin, M. Bacic, M. S. Kovacevic, K. Gavin, 2023, published scientific conference contribution Abstract: The paper presents a risk assessment model, developed in the project oVER-FLOw and further implemented in the project CROSScade, for determining the direct and indirect impacts of flooding hazards. As a consequence of flooding, transport infrastructure and flood protection systems can be significantly damaged and cause cascading effects on other infrastructure. To achieve flood resilient infrastructure, it is necessary to assess the vulnerability of critical assets in the affected area. The model uses novel vulnerability assessment methods for embankments and bridges exposed to different flood hazard scenarios allowing the asset owners to understand risk and performance of their infrastructure. Scarce financial resources are allocated on the critical assets allowing significant cost savings and avoiding the waste of non-renewable resources in strengthening large sections which have sufficient resilience. The consequence analysis is based on an improved quantification model for direct and indirect impacts of different flood hazard scenarios used for risk mapping of the affected area.
Keywords: flooding, risk assessment, critical infrastructure, economic loss
Published in DiRROS: 23.05.2024; Views: 76; Downloads: 39
 Full text (1,35 MB)
This document has many files! More... |
2. Modelling of traffic load effects in the assessment of existing road bridgesDominik Skokandić, Ana Mandić Ivanković, Aleš Žnidarič, Mladen Srbić, 2019, review article Abstract: Traffic load models used for the design of new bridges are based on conservative assumptions and have not been proven efficient for assessing safety of existing bridges. In the case of existing bridges, it is reasonable to use load models that are based on bridge weigh-in-motion data which, in addition to axle loads and spacing of bridge-crossing vehicles, provide information on bridge behaviour under traffic load. This paper provides an overview of traffic load models, as well as guidelines on the use of weigh-in-motion data when assessing condition of existing road bridges.
Keywords: prometna obtežba, tehtanje vozil med vožnjo, mostni WIM, ocenjevanje stanja, obstoječi mostovi, traffic load, weigh-in-motion, bridge WIM, condition assessment, existing bridges
Published in DiRROS: 27.03.2024; Views: 164; Downloads: 124
Full text (687,33 KB)
This document has many files! More... |
3. The challenge of integrating Life Cycle Assessment in the building design process - a systematic literature review of BIM-LCA workflowsTajda Potrč Obrecht, Martin Röck, Endrit Hoxha, Alexander Passer, 2019, published scientific conference contribution Abstract: To foster sustainable development in construction sectors, environmental impacts need to be reduced dramatically. The Life Cycle Assessment (LCA) technique is the most firmly established methodology used to quantify these environmental impacts and, therefore, has been applied with increasing frequency to assess the environmental performance of buildings. To effectively improve a building's environmental performance, an integration of LCA in the design process is required. This can be achieved by coupling LCA with digital design tools, e.g., Building Information Modelling (BIM). To identify the pro and cons of streamlining the integration of LCA and BIM, a comprehensive Systematic Literature Review (SLR) was performed. We identified more than 50 relevant BIM-LCA case studies and analysed the applied BIM-LCA workflows in detail. In most of the studies reviewed, the LCA has been applied in an early design stage. The authors primarily used LCA tools and manual or semi-automatic methods to exchange data between BIM models. In most cases, contemporary BIM-LCA workflows utilized conventional spreadsheets (e.g., Excel worksheets). However, the results of the analysis show that an automated link between LCA and BIM can be achieved if certain challenges are overcome. By automating exchange of information between BIM and LCA tools and improving the reliability of this process, the LCA application can be streamlined in design practice and, hence, the necessary improvements of the environmental performance of buildings can be supported.
Keywords: building information modelling, life cycle assessment, systematic Literature Review
Published in DiRROS: 18.03.2024; Views: 140; Downloads: 97
Full text (453,33 KB)
This document has many files! More... |
4. Roles of the reference service life (RSL) of buildings and the RSL of building components in the environmental impacts of buildingsTajda Potrč Obrecht, Roman Kunič, Sabina Jordan, Andraž Legat, 2019, published scientific conference contribution Abstract: The Life Cycle Assessment of a building is a complex analysis that also involves the use of the predicted Reference Service Life (RSL) of the building components and materials, as well as the predicted RSL of the whole building. The RSL values of individual materials and building components can be obtained from different sources and are not exactly comparable. In the present study, the influence of selected RLS values on an LCA assessment was evaluated. Three different RSL databases were used as the sources of the data to estimate the environmental impacts of selected building components (internal wooden door and external finishing coat). Two scenarios were presented. In the first scenario a building component can be reused in another building, while in the second scenario the reuse of the building component is not possible. The study showed that dependent on the selected RSL database, the results can differ by up to a factor of five. Therefore, it is very important to describe clearly the maintenance scenarios for a building in order to have a reliable comparison of the results of LCA assessments.
Keywords: reference service life, life cycle assessment, refurbishment
Published in DiRROS: 08.03.2024; Views: 177; Downloads: 130
Full text (2,89 MB)
This document has many files! More... |
5. BIM and LCA integration : a systematic literature reviewTajda Potrč Obrecht, Martin Röck, Endrit Hoxha, Alexander Passer, 2020, review article Abstract: To foster sustainable development, the environmental impacts of the construction sector need to be reduced substantially. Life cycle assessment (LCA) is the established methodology for the quantification of environmental impacts, and therefore has been increasingly applied to assess the environmental performance of buildings. By coupling LCAs with digital design tools, e.g., building information modeling (BIM), the identification of environmental hotspots and their mitigation is possible during the design process. The objective of the study is to identify the current integration approaches, and determine the pros and cons of the integration process from different viewpoints, namely, technical, informational, organizational and functional issues. Therefore, a comprehensive systematic literature review (SLR) was performed. We identified 60 relevant BIM-LCA case studies and analyzed the applied BIM-LCA workflows in detail. A total of 16 of the reviewed studies applied LCA during the early design stage. These studies used a manual or semiautomatic data exchange between the BIM models and LCA tools. In most cases, contemporary BIM-LCA workflows utilized conventional spreadsheets (e.g., Excel sheets in 16 cases). However, the analysis shows that an automated link between LCA and BIM can be achieved when overcoming the technical, organizational and informational issues discussed in the paper. This could enable the streamlining of LCA applications in design practice, and thus support the necessary improvements in the environmental performance of buildings.
Keywords: building information modeling (BIM), life cycle assessment (LCA), systematic literaturereview (SLR), environmental product declarations (EPD), workflow, bill of quantities (BoQ)
Published in DiRROS: 05.03.2024; Views: 231; Downloads: 76
Full text (2,15 MB)
This document has many files! More... |
6. Experimental carbonation study for durability assessment of novel cementitious materialsSebastijan Robič, Aljoša Šajna, Lucija Hanžič, Alisa Machner, Marie Helene Bjørndal, Klaartje De Weerdt, Yushan Gu, Benoit Bary, Rosamaria Lample, 2021, published scientific conference contribution Abstract: The design process of concrete structures is carried out using standards and guidelines, while the durability predictions of concrete structures is supported only with exposure classes and experience-based requirements. To improve durability predictions of the carbonation resistance of concrete, a numerical model is being developed within the Horizon 2020 project EnDurCrete, coupling the rate of carbonation, and the drying rate. To verify the numerical model, an accelerated carbonation study was carried out. Experiments were conducted on mortars incorporating a novel CEM II/C (S-LL) cement, developed within the EnDurCrete project, and a commercially available reference cementCEM II/A-S. EnDurCrete mortars (EnM) and reference mortars (RefM) were prepared with water-cement ratios of 0.6 and 0.5 (denoted with label extensions -06 and -05). Visual assessments and thermogravimetric analysis (TGA) were used to measure the carbonation rates, which were found to be ~1.0 mm day-0.5 in EnM-06 and ~0.6 mm day-0.5 in RefM-06, while in EnM-05 and RefM-05 the values were ~0.7 and ~0.2 mm day-0.5 respectively. Additionally, TGA shows that the initial portlandite (CH) content is ~1.5 wt% in EnM-06 as opposed to ~3.0 wt% in RefM-06. The difference in the initial CH content in the two hydrated binders might explain the difference in their carbonation rate. During the moisture transport experiments a gravimetric method was used to determine mass changes as specimens underwent drying and resaturation with and without CO2 present. The drying led to a decrease in mass, but in the presence of CO2 this mass loss was compensated by the mass gain due to uptake of CO2 during carbonation. The resaturation experiments indicate an increase in the suction porosity in the carbonated samples compared to the non-carbonated samples.
Keywords: concrete, absorption of water, carbonation, durability assessment, model verification
Published in DiRROS: 25.01.2024; Views: 206; Downloads: 141
Full text (9,29 MB)
This document has many files! More... |
7. First experiences in the development of slovenian sustainable building indicatorsSabina Jordan, Friderik Knez, Miha Tomšič, Marjana Šijanec-Zavrl, 2020, published scientific conference contribution Abstract: The construction sector is recognised as having a key impact on the life on Earth. Consequently, the EU has set clear environmental goals for 2030 and 2050, and is developing policies and tools to achieve them. One of the tools for achieving these goals is to establish a system for the evaluation of the environmental performance of buildings, with the priorities of reducing GHG emissions, saving with natural resources and preserving the environment, while maintaining sustainable development and ensuring a healthy living environment. Slovenia has joined in achieving this goal with a study on the state-of-play, commissioned a few years ago by the Ministry of the Environment and Spatial Planning, as the starting point for the development of sustainable building indicators (SBIs). The research, which included an analysis of the Slovenian legislation, commercial certification systems for sustainable buildings and development in the field of green public procurement, exposed complementary but rather different goals and views. It further showed that the Level(s), which provides a common EU approach in assessing the environmental performance of buildings, seems to be the most appropriate framework and the basis for the development of the Slovenian system of SBIs. The development of the Slovenian SBIs is currently underway within the project LIFE IP CARE4CLIMATE with the preparation of guidelines, data sources and procedures for determining the value of individual indicators for the assessment of buildings. Initial research with key construction stakeholders has shown that the solution must be linked to the national building legislation, computational methods and software tools, and also to the established planning procedures. The analyses have also shown that, parallel to developing such a system, it is essential to provide a functional supporting environment and a specific, purposely designed information platform to connect the stakeholders with the developers of the sustainable building indicators system.
Keywords: sustainable building indicators, evaluation, assessment, Level(s), CARE4CLIMATE
Published in DiRROS: 19.01.2024; Views: 187; Downloads: 94
Full text (18,89 MB)
This document has many files! More... |
8. Geological-genetic structure of Irpin city, the role of lithological factors during engineering-geological zoning and construction assessmentPavlo Zhyrnov, Iryna Solomakha, 2023, original scientific article Abstract: The scheme of engineering-construction assessment created based on engineering-geological zoning of the city’s territory is desirable among additional graphic materials in the design of master plans projects as determined by building regulations. Engineering-geological zoning provides for different ranks’ selection of engineering-geological units (EG units), which have a particular range of common engineering-geological conditions that ultimately determine the construction sites’ affiliation to a specific suitability category. Geological-genetic structure of Irpin city of Kyiv region (Ukraine) is explored in this article. A variant of the creation of a large-scale engineering-geological map and corresponding geological-lithological sections by supporting boreholes in the borders of the city based on the engineering-geological survey conducted is presented. The obtained result allowed the selection of engineering geological zoning units – engineering geological districts by general conditions of geological development and subdistricts by engineering-geological complexes of Quaternary rocks’ thickness. The analysis of soils’ geomechanical properties (engineering-geological elements) lays the foundations for the selection of engineering-geological sites based on the comparison of this information with geomorphological, hydrogeological and geodynamic data. Accounting of geological-lithological factors in the preparation of the construction assessment scheme in the project of Irpin city’s master plan has become the ultimate result.
Keywords: engineering-geological zoning, engineering-geological units, geological-genetic structure, engineering-geological map, construction assessment
Published in DiRROS: 15.01.2024; Views: 230; Downloads: 141
Full text (24,13 MB) |
9. Heavy metal signature and environmental assessment of nearshore sediments: Port of Koper (Northern Adriatic Sea)Nastja Rogan Šmuc, Matej Dolenec, Sabina Dolenec, Ana Mladenovič, 2018, original scientific article Abstract: Heavy metal abundance and potential environmental risks are reported for surface sediments (n = 21) from the Port of Koper area, Republic of Slovenia. The enrichment factor (EF) indicates minor enrichment in arsenic (As), cadmium (Cd), copper (Cu), molybdenum (Mo), lead (Pb), antimony (Sb), and zinc (Zn), moderately to severely enriched with nickel (Ni). The trace metal chemistries, in the context of sediment quality guidelines (SQG), imply adverse threshold effect concentrations (TEC) and probable effect concentrations (PEC), for Ni only. Sediment sequential leaching experiments demonstrated that the majority of heavy metals were of natural lithogenic origin and low bioavailability. The heavy metals’ potential for “Risk Assessment Code” values exhibited no or low anthropogenic environmental burden, with the exception of Mo.
Keywords: port sediments, heavy metals, chemical speciation, risk assessment, Northem Adriatic Sea
Published in DiRROS: 12.12.2023; Views: 225; Downloads: 119
Full text (6,88 MB)
This document has many files! More... |
10. Using the IUCN environmental impact classification for alien taxa to inform decision-makingSabrina Kumschick, Sandro Bertolino, Tim M. Blackburn, Giuseppe Brundu, Katie E. Costello, Maarten De Groot, Thomas Evans, Belinda Gallardo, Piero Genovesi, Tanushri Govender, 2023, original scientific article Abstract: The Environmental Impact Classification for Alien Taxa (EICAT) is an important tool for biological invasion policy and management and has been adopted as an International Union for Conservation of Nature (IUCN) standard to measure the severity of environmental impacts caused by organisms living outside their native ranges. EICAT has already been incorporated into some national and local decision-making procedures, making it a particularly relevant resource for addressing the impact of non-native species. Recently, some of the underlying conceptual principles of EICAT, particularly those related to the use of the precautionary approach, have been challenged. Although still relatively new, guidelines for the application and interpretation of EICAT will be periodically revisited by the IUCN community, based on scientific evidence, to improve the process. Some of the criticisms recently raised are based on subjectively selected assumptions that cannot be generalized and may harm global efforts to manage biological invasions. EICAT adopts a precautionary principle by considering a species’ impact history elsewhere because some taxa have traits that can make them inherently more harmful. Furthermore, non-native species are often important drivers of biodiversity loss even in the presence of other pressures. Ignoring the precautionary principle when tackling the impacts of non-native species has led to devastating consequences for human well-being, biodiversity, and ecosystems, as well as poor management outcomes, and thus to significant economic costs. EICAT is a relevant tool because it supports prioritization and management of non-native species and meeting and monitoring progress toward the Kunming–Montreal Global Biodiversity Framework (GBF) Target 6.
Keywords: biological invasions, evidence synthesis, impact assessment, managing invasive species, precautionary principle
Published in DiRROS: 11.12.2023; Views: 363; Downloads: 204
Full text (537,44 KB)
This document has many files! More... |
