261. Model updating concept using bridge Weigh-in-Motion dataDoron Hekič, Andrej Anžlin, Maja Kreslin, Aleš Žnidarič, Peter Češarek, 2023, original scientific article Abstract: Finite element (FE) model updating of bridges is based on the measured modal parameters and less frequently on the measured structural response under a known load. Until recently, the FE model updating did not consider strain measurements from sensors installed for weighing vehicles with bridge weigh-in-motion (B-WIM) systems. A 50-year-old multi-span concrete highway viaduct, renovated between 2017 and 2019, was equipped with continuous monitoring system with over 200 sensors, and a B-WIM system. In the most heavily instrumented span, the maximum measured longitudinal strains induced by the full-speed calibration vehicle passages were compared with the modelled strains. Based on the sensitivity study results, three variables that affected its overall stiffness were updated: Young’s modulus adjustment factor of all structural elements, and two anchorage reduction factors that considered the interaction between the superstructure and non-structural elements. The analysis confirmed the importance of the initial manual FE model updating to correctly reflect the non-structural elements during the automatic nonlinear optimisation. It also demonstrated a successful use of pseudo-static B-WIM loading data during the model updating process and the potential to extend the proposed approach to using random B-WIM-weighed vehicles for FE model updating and long-term monitoring of structural parameters and load-dependent phenomena.
Keywords: monitoring, bridge, viaduct, bridge weigh-in-motion (B-WIM), structural health monitoring (SHM), finite element (FE), calibration, model updating
Published in DiRROS: 29.05.2023; Views: 427; Downloads: 228
 Full text (26,28 MB)
This document has many files! More... |
262. Environmental acceptability of geotechnical composites from recycled materials : comparative study of laboratory and field investigationsMarija Đurić, Vesna Zalar Serjun, Ana Mladenovič, Alenka Mauko Pranjić, Radmila Milačič, Janez Ščančar, Janko Urbanc, Nina Mali, Alenka Sešek Pavlin, Janez Turk, Primož Oprčkal, 2023, original scientific article Abstract: The environmental properties of three geotechnical composites made by recycling wastes were investigated on a laboratory scale and in the field with the use of lysimeters designated for the revitalization of degraded mining sites. Composites were prepared by combining the mine waste with paper-mill sludge and foundry sand (Composite 1), with digestate from municipal waste and paper ash (Composite 2), and with coal ash, foundry slag and waste incineration bottom ash (Composite 3). The results of laboratory leaching tests proved that Composites 1 and 3 are envi- ronmentally acceptable, according to the legislative limits, as the potentially hazardous substances were immobilized, while in Composite 2, the legislative limits were exceeded. In the field lysimeters, the lowest rate of leaching was determined for optimally compacted Composites 1 and 3, while for Composite 2 the leaching of Cu was high. This study proved that optimally installed Composites 1 and 3 are environmentally acceptable for use in construction as an alternative to virgin materials, for the revitalization of degraded mining sites or, along with Composite 2, for closure operations with landfills. In this way, locally available waste streams are valorised and channelized into a beneficial and sustainable recycling practice.
Keywords: waste, recycling, lysimeter, potentiali hazardous substances, immobilization, revitalisation, environmental, open access
Published in DiRROS: 29.05.2023; Views: 350; Downloads: 257
Full text (3,42 MB)
This document has many files! More... |
263. Differences between 3-D printed and traditionally milled CoCr dental alloy from casted block in oral environmentMirjam Bajt Leban, Matej Kurnik, Igor Kopač, Matic Klug Jovičević, Bojan Podgornik, Tadeja Kosec, 2023, original scientific article Abstract: The aim of this study was to compare corrosion resistance and ion release in CoCr dental alloys with identical chemical compositions produced using different technologies (SLM – selective laser melting and milling from cast blocks) and heat treatment (SLM parts only). The corrosion properties were tested in artificial saliva, artificial saliva with fluoride ions, and artificial saliva with added lactic acid to simulate inflammations. The study included electrochemical tests, microstructural investigation and ion release tests in the three different environments for a total of 42 days. The best performance of CoCr as a result of potentiodynamic polarization was observed in the artificial saliva with added lactic acid, which is in contradiction with the highest ion release measured from all the materials tested and electrochemical impedance spectroscopy that showed a deterioration of the passive layer in an acidic environment. Microstructural investigation revealed that different phases precipitated by heat treatment trigger increased release of Mo and W ions. The printing method does not raise critically ion release from CoCr alloy, while the state of the surface greatly impacts the extent of the ion release. This study demonstrates the importance of an interdisciplinary approach to the study of corrosion and biocompatibility in dental alloys.
Keywords: CoCr dental alloy, selective laser melting, corrosion, ion release, artificial saliva
Published in DiRROS: 29.05.2023; Views: 358; Downloads: 299
Full text (9,28 MB)
This document has many files! More... |
264. Development and testing of a railway bridge weigh-in-motion systemDonya Hajializadeh, Aleš Žnidarič, Jan Kalin, Eugene J. OBrien, 2020, original scientific article Abstract: This study describes the development and testing of a railway bridge weigh-in-motion (RB-WIM) system. The traditional bridge WIM (B-WIM) system developed for road bridges was extended here to calculate the weights of railway carriages. The system was tested using the measured response from a test bridge in Poland, and the accuracy of the system was assessed using statically-weighed trains. To accommodate variable velocity of the trains, the standard B-WIM algorithm, which assumes a constant velocity during the passage of a vehicle, was adjusted and the algorithm revised accordingly. The results showed that the vast majority of the calculated carriage weights fell within %5% of their true, statically-weighed values. The sensitivity of the method to the calibration methods was then assessed using regression models, trained by di%erent combinations of calibration trains.
Keywords: bridge weigh-in-motion, railway bridge loading, bridge instrumentation, B-WIM
Published in DiRROS: 22.05.2023; Views: 325; Downloads: 157
Full text (6,18 MB)
This document has many files! More... |
265. Antibacterial properties and cytotoxicity of 100% waste derived alkali activated materials : slags and stone wool-based bindersCaterina Sgarlata, Giovanni Dal Poggetto, Federica Piccolo, Michelina Catauro, Katja Traven, Mark Češnovar, Hoang Nguyen, Juho Yliniemi, Luisa Barbieri, Vilma Ducman, Isabella Lancellotti, Cristina Leonelli, 2021, original scientific article Abstract: In this study we compare the leaching behavior and the antibacterial and cytotoxic properties of 100% slag or stone wool derived alkali activated materials. The antibacterial activity was measured as the inhibiting capacity against two Gram- negative bacterial strains, Escherichia coli and Pseudomonas aeruginosa and one Gram-positive bacterial strain: Enterococcus faecalis. The cytotoxicity properties were tested on mouse embryonic fibroblast NIH-3T3 cell-line. It was proved that the high quality of the 3D aluminosilicate network of the consolidated materials obtained from powders of CaO or MgO-rich slags or stone wool, opportunely activated with NaO and/or Na-silicate, was capable of stabilizing heavy metal cations. The concentrations of leachate heavy cations were lower than the European law limit when tested in water. The effect of additives in the composites, basal fibers or nanocellulose, did not reduce the chemical stability and slightly influenced the compressive strength. Weight loss in water increased by 20% with basalt fibers addition, while it remained almost constant when nanocellulose was added. All the consolidated materials, cement-like in appearance, exhibited limited antibacterial properties (viability from 50 to 80% depending on the bacterial colony and the amount of sample) and absence of cytotoxicity, envisaging good acceptance from part of the final consumer and zero ecological impact. CaO-rich formulations can replace ordinary Portland cement (showing bacterial viability at 100%) with a certain capability for preventing the reproduction of the E. coli and S. aureus bacteria with health and environmental protection results.
Keywords: antibacterial properties, cytotoxicity, alkali-activated materials, slag, stone wool, waste utilization, social acceptance
Published in DiRROS: 22.05.2023; Views: 339; Downloads: 187
Full text (2,31 MB)
This document has many files! More... |
266. Alkali activation of metallurgical slags : reactivity, chemical behavior, and environmental assessmentIsabella Lancellotti, Federica Piccolo, Katja Traven, Mark Češnovar, Vilma Ducman, Cristina Leonelli, 2021, original scientific article Abstract: Alkali-activated materials (AAMs) represent a promising alternative to conventional building materials and ceramics. Being produced in large amounts as aluminosilicate-rich secondary products, such as slags, they can be utilized for the formulation of AAMs. Slags are partially crystalline metallurgical residues produced during the high temperature separation of metallic and non-metallic materials in the steelmaking processes. In the present study, the electric arc furnace carbon or stainless steel slag (EAF) and secondary metallurgical slag such as ladle furnace basic slag (LS) were used as precursors in an alkali-activation process. EAF slag, with its amorphous fraction of about 56%, presented higher contents of soluble Si and Al species with respect to ladle slag R (35%). However, both are suitable to produce AAM. The leaching behavior shows that all the release values are below the regulation limit. All the bivalent ions (Ba, Cd, Cu, Ni, Pb, and Zn) are well immobilized in a geopolymeric matrix, while amphoteric elements, such as As and Cr, show a slight increase of release with respect to the corresponding slag in alkaline and aqueous environments. In particular, for Sb and As of AAM, release still remains below the regulation limits, while Mo presents an increase of leaching values that slightly exceeds the limit for landfill non-dangerous waste.
Keywords: slag, aluminosilicate materials, chemical reactivity, cold consolidation, alkali activation, leaching test, open access
Published in DiRROS: 22.05.2023; Views: 360; Downloads: 183
Full text (4,49 MB)
This document has many files! More... |
267. Technical and radiological characterisation of fly ash and bottom ash from thermal power plantEmilija Fidanchevski, Biljana Angjusheva, Vojo Jovanov, Pece Murtanovski, Ljubica Vladiceska, Nikolina Stamatovska Aluloska, Jelena Krneta Nikolić, Andrej Ipavec, Katarina Šter, Maruša Mrak, Sabina Dolenec, 2021, original scientific article Abstract: Huge quantities of fly ash and bottom ash are generated from thermal power plants and it presents great concern for country, mainly due to the environmental effects. In this study, fly ashes and bottom ash were characterized from technical and radiological aspects. Health effect due to the activity of radionuclides 226Ra, 232Th and 40K was estimated via radium equivalent activity (Raeq), external hazards index (Hex), the external absorbed dose rate (D) and annual effective dose rate (EDR). The specific surface area (40.25 m2 g−1), particle density (1.88 g cm−3) and LOI (23.49%) were typical for bottom ash. Siliceous fly ash contained 32% reactive silica. The annual effective dose rate for all ashes is ≤ 0.2 mSv y−1. Both, fly ash and bottom ash present potential secondary raw materials to be used for building purposes as result of their technological and radiological assessment.
Keywords: fly ash, bottom ash, gamma spectrometry, building materials
Published in DiRROS: 22.05.2023; Views: 309; Downloads: 147
Full text (1009,85 KB)
This document has many files! More... |
268. Biophysical properties of foamed and solid polymers used in orthotics and prostheticsKlemen Bohinc, Anže Abram, Anamarija Zore, Roman Štukelj, Ana Lenarčič, Rajko Vidrih, Andrijana Sever Škapin, 2021, original scientific article Abstract: Orthotic and prosthetic materials should have good mechanical and antibacterial properties. Therefore, in our study, we consider four common foamed closed-cells and two solid polymeric materials regarding their mechanical behaviour and tendency for bacterial adhesion. For all materials, the surface roughness, hydrophobicity, zeta potential, tensile properties, hardness and CIE color parameters were measured. We found that foamed polymeric materials have higher roughness, higher hydrophobicity, lower Young's modulus, lower maximum tensile strength and lower hardness than solid materials. Bacterial adhesion test measurements based on observation by scanning electron microscopy show much a lower adhesion extent of S. aureus on solid materials than on foamed materials. The measured biophysical properties could be the key data for users to select the optimal materials.
Keywords: surface characterization, bacterial adhesion, foamed materials, prosthetic and orthotic material, surfaces
Published in DiRROS: 22.05.2023; Views: 291; Downloads: 184
Full text (3,14 MB)
This document has many files! More... |
269. Impact of metakaolin on mechanical performance of flax textile-reinforced cement-based compositesFilip Majstorović, Václav Sebera, Maruša Mrak, Sabina Dolenec, Marco Wolf, Laetitia Sarah Jennifer Marrot, 2022, original scientific article Abstract: This study presents research on the effect of Portland cement (PC) replacement with metakaolin on the mechanical behavior of flax textile-reinforced cementitious matrices (TRCM). The composition of cementitious matrices and in-situ flax fibres was determined using X-ray diffraction and thermogravimetric analysis, while the reinforcement efficiency of the textile and mechanical behavior of TRCMs was investigated by three-point bending tests and finite element analysis. High amounts of PC replacement with metakaolin provided a calcium hydroxide-free environment, more suitable for the natural fibres, to avoid their degradation and embrittlement and, thus, significantly contribute to the ductility of the cement-based composite material.
Keywords: textile-reinforced concrete (TRC), flax textile, natural fibres, finite element, metakaolin, cement-based composites, open access
Published in DiRROS: 22.05.2023; Views: 389; Downloads: 183
Full text (8,40 MB)
This document has many files! More... |
270. Mechanical performance of timber connections made of thick flexible polyurethane adhesivesJaka Gašper Pečnik, Igor Gavrić, Václav Sebera, Meta Kržan, Arkadiusz Kwiecień, BogusŁaw Zając, Boris Azinović, 2021, original scientific article Abstract: This study investigates timber connections with flexible polyurethane adhesives, which prove to have the po-tential for timber-adhesive composite structures without mechanical connections for seismic regions. Results of conducted cyclic double lap-shear adhesive timber joints tests were compared with available experimental re-sults on timber connections with standard mechanical dowel-type fasteners and with results of numerical finite element analysis. The study found that the shear strength, elastic stiffness and strength degradation capacity of the flexible adhesive connections were significantly higher compared to mechanical fasteners commonly used in seismic-resistant timber connections. The latter, however, manifested larger ultimate displacements but also yielded at lower displacements.
Keywords: flexible adhesive, timber connection, polyurethane, double lap-shear, cyclic loading, energy dissipation, open access
Published in DiRROS: 19.05.2023; Views: 395; Downloads: 255
Full text (5,16 MB)
This document has many files! More... |
