1. Why geopolymers and alkali-activated materials are key components of a sustainable world : a perspective contributionWaltraud M. Kriven, Cristina Leonelli, John L. Provis, Aldo R. Boccaccini, Cyril Attwell, Vilma Ducman, Claudio Ferone, Sylvie Rossignol, Tero Luukkonen, Jannie S. J. Van Deventer, José V. Emiliano, Jérôme E. Lombardi, 2024, original scientific article Abstract: This perspective article delves into the transformative potential of alkali-activated materials, acid-activated materials, and geopolymers in mitigating climate change and market challenges. To harness the benefits of these materials, a comprehensive strategy is proposed. This strategy aims to integrate these materials into existing construction regulations, facilitate certification, and promote market access. Emphasizing research and innovation, the article advocates for, increased funding to refine the chemistry and production of these materials, prioritizing low-cost alternatives and local waste materials. Collaboration between academia and industry is encouraged to expedite technological advances and broaden applications. This article also underscores the need to develop economic and business models emphasizing the long-term benefits of these materials, including lower life-cycle costs and reduced environmental impact. Incentivizing adoption through financial mechanisms like tax credits and subsidies is suggested. The strategy also includes scaling up production technology, fostering industrial collaboration for commercial viability, and developing global supply chains. Educational programs for professionals and regulators are recommended to enhance awareness and adoption. Additionally, comprehensive life-cycle assessments are proposed to demonstrate environmental benefits. The strategy culminates in expanding the applications of these materials beyond construction, fostering international collaboration for knowledge sharing, and thus positioning these materials as essential for sustainable construction and climate change mitigation.
Keywords: geopolymers, alkali activated materials, perspective
Published in DiRROS: 15.04.2024; Views: 113; Downloads: 61
 Full text (1,63 MB)
This document has many files! More... |
2. Evaluation of fly ash-based alkali activated foams at room and elevated temperaturesKatja Traven, Mark Češnovar, Srečo D. Škapin, Vilma Ducman, 2020, published scientific conference contribution Abstract: Alkali activated materials (AAM) are, in their broadest classification, any binder systems derived by the reaction of an alkali metal source (silicates, alkali hydroxides, carbonates , sulphates) with a solid, amorphous alumosilicate powder (found in precursors such as slag, fly ash and bottom ash). A wide variety of products can be obtained by the alkali activation process and could replace traditional construction products. Among the se, alkali activated foams (AAF) represent one of the most promising materials, owing to their economically accessible alumosilicate rich source materials, including industrial waste materials, clean processing, higher added value and most importantly, pro ducts with competitive properties. In the present study, the properties of alkali activated fly ash - based foam materials were studied at room temperature as well as at elevated temperatures (up to 1200 °C ) in order to develop a durable material in terms o f mechanical properties and suitability for high temperature applications.
Keywords: lightweight porous insulating material, alkali activated materials, microstructural analysis
Published in DiRROS: 05.03.2024; Views: 106; Downloads: 45
Full text (970,74 KB)
This document has many files! More... |
3. Foundry wastes as a potential precursor in alkali activation technologyBarbara Horvat, Alenka Sešek Pavlin, Vilma Ducman, 2020, published scientific conference contribution Abstract: In this study the amount of amorphous phase of elements useful in alkali activation of waste materials produced by the foundry industry was determined. Waste foundry sands, foundry flue gas and waste casting cores were alkali activated, and waste green ceramics and bottom ash were added to one of the foundry sand samples to shorten the time for producing measurable compressive strength from 1.5 years to 1 week.
Keywords: alkali activated materials, foundry wastes, compressive strength, upcycling, circular ecnomy
Published in DiRROS: 01.03.2024; Views: 121; Downloads: 56
 Link to file
This document has many files! More... |
4. The deformation of alkali-activated materials at different curing temperaturesMark Češnovar, Katja Traven, Vilma Ducman, 2020, published scientific conference contribution Abstract: Alkali activation is a chemical process whereby materials rich in aluminosilicate, which dissolves in basic media at room temperature, form binding phases by polycondensation. The alkali- activated materials (AAM) are a promising alternative to binding materials such as cement or other products in civil engineering (van Deventer et al., 2012). This study investigates the early age shrinkage behavior of Slovenian ladle and electric arc furnace slag - based alkali activated materials at different curing temperatures. The dimensions of specimens cured at room temperature and elevated temperatures up to 90 °C were measured over the first 7 hours (every 10 min). The results show that the most shrinkage occurred at the highest temperature, owing to the highest rate of evaporation of liquid content. Loss of mass follows from the drying shrinkage.
Keywords: alkali activated materials, shrinkage, compressive strength
Published in DiRROS: 01.03.2024; Views: 115; Downloads: 80
Full text (670,52 KB)
This document has many files! More... |
5. Alternative alkali activators based on waste bottle glass and waste cathode-ray tube glassKatja Koenig, Katja Traven, Vilma Ducman, 2021, published scientific conference contribution Abstract: Alkali-activated binders are an environmentally friendly alternative to Portland cement, particularly when locally-available raw materials are used. It is well known that alkali activation with a sodium silicate activator generates a hardened binder with higher compressive strength than a binder hardened with sodium hydroxide. As the alkali-silicate activators are produced through energy extensive processes, and their use can significantly increase the carbon footprint of the final products, it is of great significance to develop alternative alkaline activators based on locally-available waste materials. This article assesses the potential to apply waste bottle glass and waste cathode-ray tube (CRT) glass to synthesise alternative alkali activators by the hydrothermal method. Inductively coupled plasma-optical emission spectrometry (ICP-OES) was used to determine silicon and aluminium content in the alternative activators. The influence of dissolution process parameters (time, temperature, particle size) on the concentrations of silicon and aluminium in the alternative activators was investigated. The alternative activators with silicon concentration up to 19 g/L and aluminium concentration up to 0.9 g/L were prepared at T = 120 °C and boiling time 24 h. The alternative alkali activators and, for comparison, also commercial sodium silicate were used in the alkali activation of fly ash powder. The formed pastes were cured at 70 °C for 72 h. Mechanical strength measurements indicated that alkali activation of fly ash with the optimal alternative activator yielded hardened paste with compressive strength of 33 MPa. However, the compressive strength of hardened paste prepared from fly ash and commercial sodium silicate reached 70 MPa. Part of this difference can be ascribed to the lower density of hardened pastes prepared with alternative activators.
Keywords: alkali -activated materials, alternative alkali activators, waste bottle glass, waste cathode -ray tube glass, fly ash, hydrothermal method
Published in DiRROS: 25.01.2024; Views: 170; Downloads: 113
Full text (14,96 MB)
This document has many files! More... |
6. Particle size manipulation as an influential parameter in the development of mechanical properties in electric arc furnace slag-based AAMKatja Traven, Mark Češnovar, Vilma Ducman, 2019, original scientific article Abstract: Alkali-activated materials (AAM) have gained recognition as a promising alternative to technical ceramic and building materials owing to the lower energy demands for production and the potential to use slag as a precursor. In the present study, five sets of slag-based AAM pastes were prepared with different particle sizes (fractions d < 63, 63 < d < 90, and 90 < d < 125 μm in different mass ratios) under the same curing regime and using a fixed precursor to activator (water) mass ratio. Precursors and the hardened AAM are evaluated using BET, XRD, XRF, SEM, FTIR, reactivity of precursors by leaching, and mercury intrusion porosimetry (MIP). Chemical analysis indicated only marginal differences among the different-sized fractions of input materials, whereas the BET surface area and reactivity among the precursors differed significantly-smaller particles had the largest surface area, and thus, higher reactivity. The mineralogical differences between the precursors and hardened AAM were negligible. The results revealed that compressive strength was significantly influenced by particle size, i.e., a threefold increase in strength when the particle size was halved. Microstructural evaluation using MIP confirmed that the porosity was the lowest in AAM with the smallest particle size. The low porosity and high reactivity of the fine fractions led to the highest compressive strength, confirming that manipulation of particle size can significantly influence the mechanical properties.
Keywords: alkalijsko aktivirani materiali, žlindra iz obločne peči, mehanska aktivacija, mehanske lastnosti, poroznost, alkali-activated materials (AAM), electric arc furnace steel slag, mechanical activation, mechanical properties, porosity
Published in DiRROS: 22.11.2023; Views: 253; Downloads: 132
Full text (2,26 MB)
This document has many files! More... |
7. RILEM TC 247-DTA round robin test : mix design and reproducibility of compressive strength of alkaliactivated concretesJohn L. Provis, Kamel Arbi, Susana Bernal, Dali Bondar, Anja Buchwald, Arnaud Castel, Sundararaman Chithiraputhiran, Martin Cyr, Alireza Dehghan, Katja Dombrowski-Daube, Ashish Dubey, Vilma Ducman, Gregor J. G. Gluth, Sreejith Nanukuttan, Karl Peterson, Francisca Puertas, Arie van Riessen, Manuel Torres-Carrasco, Guang Ye, Yibing Zuo, 2019, original scientific article Abstract: The aim of RILEM TC 247-DTA Durability Testing of Alkali-Activated Materials is to identify and validate methodologies for testing the durability of alkali-activated concretes. To underpin the durability testing work of this committee, five alkali-activated concrete mixes were developed based on blast furnace slag, fly ash, and flash-calcined metakaolin. The concretes were designed with different intended performance levels, aiming to assess the capability of test methods to discriminate between concretes on this basis. A total of fifteen laboratories worldwide participated in this round robin test programme, where all concretes were produced with the same mix designs, from single-source aluminosilicate precursors and locally available aggregates. This paper reports the mix designs tested, and the compressive strength results obtained, including critical insight into reasons for the observed variability in strength within and between laboratories.
Keywords: alkali-activated materials (AAM), mechanical properties, test method, Rilem TC, durability
Published in DiRROS: 14.09.2023; Views: 235; Downloads: 138
Full text (431,19 KB)
This document has many files! More... |
8. Life cycle assessment of prefabricated geopolymeric façade cladding panels made from large fractions of recycled construction and demolition wasteDavor Kvočka, Anja Lešek, Friderik Knez, Vilma Ducman, Matteo Panizza, Constantinos Tsoutis, Adriana Bernardi, 2020, original scientific article Abstract: The construction and demolition sector is one of the biggest consumers of natural resources in the world and consequently, one of the biggest waste producers worldwide. The proper management of construction and demolition waste (CDW) can provide major benefits for the construction and recycling industry. However, the recycling rate of CDW is relatively low, as there is still a lack of confidence in the quality of recycled CDW materials. Therefore, new research projects are looking for innovative solutions within recycling of CDW in order to overcome uncertainties currently associated with the use of construction products made from recycled or re-used CDW. In this paper, a “cradle-to-cradle” life cycle assessment (LCA) study has been conducted to investigate the environmental performance of the prefabricated geopolymeric façade cladding panels made from large fractions of CDW. The LCA results indicate that the majority of the environmental burden arises within the manufacturing stage; however, the environmental burden can be reduced with simple optimisation of the manufacturing process. Furthermore, the environmental impact of the prefabricated geopolymeric façade cladding panels is generally lower than the environmental burden associated with the façade cladding panels made from virgin materials.
Keywords: construction and demolition waste, alkali activated materials, geopolymers, LCA
Published in DiRROS: 24.08.2023; Views: 246; Downloads: 126
Full text (2,03 MB)
This document has many files! More... |
9. Characterization of fly ash alkali activated foams obtained using sodium perborate monohydrate as a foaming agent at room and elevated temperaturesLidija Korat, Vilma Ducman, 2020, original scientific article Abstract: Alkali activated foams have been extensively studied in recent years, due to their high performance and low environmental footprint compared to foams produced via other methods. Three types of fly ash differing in chemical and mineralogical composition and specific surface were used to synthesize alkali activated foams. Sodium perborate monohydrate was added as a foaming agent and sodium dodecyl sulphate as a stabilizing agent. Foams were characterized at room temperature and after exposure to an elevated temperature (1,000 °C). Densities from 1.2 down to 0.3 g/cm 3 were obtained, depending on the type of fly ash and quantity of foaming agent added. Correspondingly, compressive strength ranged from 1 to 6 MPa. Comparing all three fly ashes the most favorable results, in terms of density and corresponding compressive strength, were achieved from the fly ash with the highest amounts of SiO 2 and Al2 O 3 , as well as the highest amorphous phase content i.e., RI fly ash. Furthermore, after firing to 1,000 °C, the density of samples prepared using fly ash RI remained approximately the same, while the compressive strength increased on average by 50%. In the other two types of fly ash the density increased slightly after firing, due to significant shrinkage, and compressive strength increased by as much as 800%. X-ray powder diffraction analysis confirmed the occurrence of a crystallization process after firing to 1,000 ° C, which resulted in newly formed crystal phases, including nepheline, sodalite, tridymite, and gehlenite.
Keywords: foamed alkali activated materials, geopolymers, properties, micro-CT
Published in DiRROS: 22.08.2023; Views: 256; Downloads: 169
Full text (7,94 MB)
This document has many files! More... |
10. Evaluation of locally available amorphous waste materials as a source for alternative alkali activatorsKatja Koenig, Katja Traven, Majda Pavlin, Vilma Ducman, 2021, original scientific article Abstract: The production of alkali-activated materials with excellent mechanical performance requires the use of waterglass, which has a significant carbon footprint. Such materials can have a lower carbon footprint if we replace water glass with alternative activators sourced from waste. In this study, we assessed the suitability of locally available amorphous waste materials (stone wool, glass wool, bottle glass and cathode-ray tube glass) as a source for the preparation of alternative alkali activators. We quantified the amount of silicon and aluminium dissolved in the activator solutions via inductively coupled plasma-optical emission spectrometry. The alternative activators were then used to produce alkali-activated fly ash and slag. The compressive strength values of alkali-activated fly ash specimens upon the addition of NaOH, water glass and the most promising alternative activator were 38.98 MPa, 31.34 MPa and 40.37 MPa, respectively. The compressive strength of slag specimens activated with alternative activators with the highest concentration of dissolved silicon (21 g/L) was, however, 70% higher than the compressive strength of slag specimens activated with only 10 M sodium hydroxide. The compressive strength of slag specimens with the addition of the most promising alternative activator was significantly lower (3.5 MPa) than the compressive strength of those that had been activated by commercial water glass (34.3 MPa).
Keywords: alkalijsko aktivirani materiali, alternativni aktivatorji, lastnosti, alkali activated materials/geopolimers, alternative activators, properties
Published in DiRROS: 22.08.2023; Views: 220; Downloads: 150
Full text (6,02 MB)
This document has many files! More... |
