Search the repository

A+ | A- | | SLO | ENG

Abstract: This article investigated the effect of waste polyethylene (PE) on the modified asphalt binders’ rheological behavior from a statistical point of view. The interlaboratory testing results from the RILEM Technical Committee 279 Valorization of Waste and Secondary Materials for Roads Task Group 1 were used for this purpose. First, an unaged 70/100 penetration graded neat binder was selected as the reference material. Next, a single 5 % content of waste PE additives (PE-pellets and PE-shreds) was mixed with a 95 % neat binder to prepare two PE modified binders. Then, dynamic shear rheometer–based temperature-frequency sweep tests were performed over a wide range of temperatures and frequencies to evaluate the rheological properties of these three binders. Different rheological behaviors were observed in the isochronal plots at high temperatures. Based on a reproducibility precision requirement proposed for phase angle, 28°C was set as the transition temperature across the rheological behaviors. Next, according to the three rheological behaviors defined in a previous study by the authors, statistical analysis was introduced to identify sensitive rheological parameters and determine the thresholds. Results indicate that the phase angle measured above 28°C and 1.59 Hz can be used as a sensitive parameter to discriminate the three rheological behaviors of PE modified binders. The thresholds among different behaviors were also calculated as an example for phase angle measured at the highest common testing temperature of 70°C. Additional experimental evaluations on more types of PE modified binders, especially at intermediate and high temperatures, are recommended to better understand their influence on the rheological behavior of PE modified binders.
Keywords: bitumen, polietilen, reologija, medlaboratorijska primerjava
Published in DiRROS: 20.02.2024; Views: 136; Downloads: 62
Full text (1,19 MB)
This document has many files! More...

Keywords: medium-carbon steel, tempering, strengthening, mechanical properties, microstructure
Published in DiRROS: 02.02.2024; Views: 160; Downloads: 78
Full text (9,82 MB)
This document has many files! More...

Abstract: This research study presents a heat transfer model aimed at estimating the thermal and physical response of intumescent coatings. The numerical model is inspired by the outcomes of an experimental study focused on analysing the insulating effectiveness of a commercial intumescent coating for a range of heating conditions and initial coating thickness. The model solves the one-dimensional heat conduction problem using the finite-difference Crank-Nicolson method, and it assumes that the effectiveness of intumescent coatings is mainly dependent on their ability to develop swelled porous char. The coating swelling is implemented in the model by adopting an approach based on expanding the mesh representing the physical domain in proximity to the substrate-coating interface. The model described herein offers researchers and engineers a tool to estimate the heat transfer of swelling intumescent coatings (i.e. in-depth thermal gradient). Outcomes of the analysis shown herein demonstrate that the heat conduction within intumescent coatings is governed by the physical coating swelling and the thermal conditions at the coating-substrate interface. The numerical model shows that its accuracy is highly influenced by the coating thickness ahead of the reaction zone. Consequently, the coating swelling rate plays a key role, while the thermo-physical properties of the intumescent coating have a secondary effect. According to its assumptions, the model defines a quasi-steady-state thermal problem: it is more accurate for conditions close to steady-state (e.g. high heat fluxes), but it loses accuracy for cases characterised by transient phenomena (e.g. phases prior to the onset of swelling and low heat fluxes).
Keywords: intumescent coatings, heat transfer, numerical model, swelling, fire safety
Published in DiRROS: 08.01.2024; Views: 180; Downloads: 34
Full text (1,21 MB)
This document has many files! More...

Abstract: Restorations in dentistry must reproduce the aspect of the patient’s natural teeth and require non-toxicity, biocompatibility, and good mechanical properties in order to last longer. Restorations are permanently in contact with microbes that can adhere to and form biofilms. The purpose of this study was to determine the adhesion extent of Streptococcus mutans to polymethyl methacrylate (PMMA) resin base containing TiO2 nanoparticles. To understand the adhesion of Streptococcus mutans on the modified resin-based surfaces, the following surface properties were measured: the roughness, contact angle, zeta potential and CIE color parameters. Evaluation of tensile stress performance in TiO2 modified PMMA showed that the maximum tensile stress of the modified PMMA resin decreases with an increasing amount of TiO2 nanoparticles. The increasing amount of TiO2 decreases the roughness and causes contact angles in the border between hydrophilic and hydrophobic surfaces. All the studied surfaces are negatively charged and added TiO2 tends to increase the zeta potential. The addition of TiO2 nanoparticles increases the lightness and decreases the intensity of the red and yellow color. The increasing addition of TiO2 nanoparticles into PMMA increases the morphological change of bacterial cells.
Keywords: bacterial adhesion, Streptococcus mutans, polymethyl methacrylate resin, TiO2, surface properties
Published in DiRROS: 20.12.2023; Views: 170; Downloads: 86
Full text (14,32 MB)
This document has many files! More...

Abstract: The effects of two metallocene ethylene-propylene-based elastomers (m-EPR1 and m-EPR2) differing in molecular mass and viscosity on mechanical, rheological and interfacial properties were compared. The m-EPR elastomers were added to iPP in 2.5, 5, 10, 15, and 20 vol.%. Torque values, elongation at break and impact strength measured of the iPP/m-EPR1 blends were higher than the iPP/m-EPR2 blends due to higher molten viscosity of m-EPR1 than m-EPR2 copolymer. Slight differences in Young moduli as well as in tensile strength at yield and at break might indicate that tensile properties of iPP/m-EPR blends were not significantly affected by difference in viscosity or molecular mass, miscibility and spherulite size. Optimization diagrams indicated the metallocene m-EPR copolymers are efficient impact modifiers for polypropylene and showed good balancing of mechanical properties in iPP/m-EPR blends.
Keywords: isotactic polypropylene, metallocene ethylene-propylene-based elastomers, blend, mechanical properties, adhesion parameters
Published in DiRROS: 13.12.2023; Views: 205; Downloads: 99
Full text (3,19 MB)
This document has many files! More...