Search the repository

A+ | A- | | SLO | ENG

Abstract: The recombination of neutral oxygen atoms in the ground state on the oxidized nickel samples was studied experimentally in the range of pressures where the maximum density occurs in weakly ionized low-pressure oxygen plasma, i.e. between 40 and 200 Pa. The recombination coefficient was determined in the flowing afterglow. The source of oxygen atoms was plasma sustained in a quartz tube of inner diameter 4.7 mm by a microwave discharge in the surfatron mode. The recombination coefficient was determined in the afterglow chamber, which was a Pyrex tube with an inner diameter of 36 mm. The density of oxygen atoms in the afterglow chamber was varied by adjusting the discharge power, the gas flow, the pressure, and the position of a recombinator. Such flexibility of the experimental system enabled adjustment of the temperature of the oxidized nickel samples independently from the O-atom density in its vicinity or other parameters. The density of oxygen atoms in the afterglow chamber at various system parameters was determined by the Šorli method, which is reliable, and has an accuracy of about 20%. The recombination coefficient was determined by calorimetry. The coefficient was inversely proportional to the square root of the pressure and exponentially to the sample temperature. Systematic measurements performed at various pressures and temperatures enabled empirical formula, which were explained qualitatively by recombination kinetics.
Keywords: heterogenous surface recombination, recombination coefficient, nickel, nickel oxide, temperature
Published in DiRROS: 30.08.2023; Views: 334; Downloads: 198
Full text (2,44 MB)
This document has many files! More...

Abstract: Secondary raw materials (SRMs) tend to be a valuable replacement for finite virgin materials especially since construction works (i.e., building and civil engineering work such as road construction) require vast quantities of raw materials. Using SRM originating from recycling a broad range of inorganic waste materials (e.g., mining waste, different industrial wastes, construction, and demolition waste) has been recognized as a promising, generally more cost-efficient, and environmentally friendly alternative to the exploitation of natural resources. Despite the benefits of using SRM, several challenges need to be addressed before using SRM even more. One of them is the long-term durability and little-known response of construction works built using such alternative materials. In this paper, we present the activities to establish a fully functioning digital twin (DT) of a road constructed using SRM. The first part of the paper is devoted to the theoretical justification of efforts and ways of establishing the monitoring systems, followed by a DT case study where an integrated data environment synthesizing a Building Information Model and monitored data is presented. Although the paper builds upon a small scale, the case study is methodologically designed to allow parallels to be drawn with much larger construction projects.
Keywords: digital twins, road construction, circular economy
Published in DiRROS: 19.07.2023; Views: 287; Downloads: 195
Full text (4,36 MB)
This document has many files! More...

Published in DiRROS: 03.07.2023; Views: 452; Downloads: 267
Full text (4,31 MB)
This document has many files! More...

Abstract: Alkali-activated foams (AAFs) are inorganic porous materials that can be obtained at temperatures well below 100° C with the use of inorganic wastes as aluminosilicate precursors. In this case, fly ash derived from a Slovenian power plant has been investigated. Despite the environmental benefits per se, due to saving of energy and virgin materials, when using waste materials, it is of extreme importance to also evaluate the potential leaching of heavy metal cations from the alkali-activated foams. This article presents an environmental study of a porous geopolymer derived from this particular fly ash, with respect to the leachability of potentially hazardous elements, its environmental toxicity as determined by biological testing, and the environmental impact of its production. In particular, attention was focused to investigate whether or not 1,000 °C-fired alkali- activated fly ash and metakaolin-based foams, cured at 70 °C, are environmentally friendlier options compared to unfired ones, and attempts to explain the rationale of the results were done. Eventually, the firing process at 1,000 ° C, apart from improving technical performance, could reinforce heavy metal cation entrapment within the aluminosilicate matrix. Since technical performance was also modified by addition of different types of activators (K-based or Na-based), as well as by partial replacement of fly ash with metakaolin, a life cycle assessment (LCA) analysis was performed to quantify the effect of these additions and processes (curing at 70 ° C and firing at 1,000 °C) in terms of global warming potential. Selected samples were also evaluated in terms of leaching of potentially deleterious elements as well as for the immobilization effect of firing. The leaching test indicated that none of the alkali-activated material is classified as hazardous, not even the as-received fly ash as component of new AAF. All of the alkali-activated foams do meet the requirements for an inertness. The highest impact on bacterial colonies was found in samples that did not undergo firing procedures, i.e., those that were cured at 70 °C, which induced the reduction of bacterial Enterococcus faecalis viability. The second family of bacteria tested, Escherichia coli, appeared more resistant to the alkaline environment (pH = 10–12) generated by the unfired AAMs. Cell viability recorded the lowest value for unfired alkali-activated materials produced from fly ash and K-based activators. Its reticulation is only partial, with the leachate solution appearing to be characterized with the most alkaline pH and with the highest ionic conductivity, i.e., highest number of soluble ions. By LCA, it has been shown that 1) changing K-based activators to Na-based activators increases environmental impact of the alkali-activated foams by 1%–4% in terms of most of the impact categories (taking into account the production stage). However, in terms of impact on abiotic depletion of elements and impact on ozone layer depletion, the increase is relatively more significant (11% and 18%, respectively); 2) replacing some parts of fly ash with metakaolin also results in relatively higher environmental footprint (increase of around 1%–4%, while the impact on abiotic depletion of elements increases by 14%); and finally, 3) firing at 1,000°C contributes significantly to the environmental footprint of alkali- activated foams. In such a case, the footprint increases by around one third, compared to the footprint of alkali-activated foams produced at 70 ° C. A combination of LCA and leaching/toxicity behavior analysis presents relevant combinations, which can provide information about long-term environmental impact of newly developed waste-based materials.
Keywords: alkali activated materials, geopolimers, leaching, LCA
Published in DiRROS: 20.06.2023; Views: 279; Downloads: 161
Full text (3,42 MB)
This document has many files! More...

Abstract: An efficient approach for tailoring surface properties of polymers is presented, which enables rapid modification leading to superhydrophilic properties. The approach is based on vacuum-ultraviolet radiation (VUV) pretreatment of the surface to create reactive dangling bonds. This step is followed by a second treatment using neutral oxygen atoms that react with the dangling bonds and form functional groups. The beneficial effect of VUV pretreatment for enhanced functionalization was clearly demonstrated by comparing VUV pretreatment in plasmas created in different gases, i.e., hydrogen, nitrogen, and oxygen, which differ in the intensity of VUV/UV radiation. The emission intensity of VUV radiation for all gases was measured by vacuum ultraviolet spectroscopy. It was shown that VUV has a strong influence on the treatment time and final surface wettability. A superhydrophilic surface was obtained only if using VUV pretreatment. Furthermore, the treatment time was significantly reduced to only a second of treatment. These findings show that such an approach may be used to enhance the surface reaction efficiency for further grafting of chemical groups.
Keywords: plasma treatment, vacuum-ultraviolet radiation treatment, surface functionalization, polymer polyvinyl chloride, vacuum-ultraviolet spectroscopy, vacuum-ultraviolet photons
Published in DiRROS: 06.06.2023; Views: 382; Downloads: 193
Full text (4,42 MB)
This document has many files! More...