| Naslov: | Particle size manipulation as an influential parameter in the development of mechanical properties in electric arc furnace slag-based AAM |
|---|
| Avtorji: | ID Traven, Katja (Avtor)
ID Češnovar, Mark (Avtor)
ID Ducman, Vilma (Avtor) |
|---|
| Datoteke: |  URL - Izvorni URL, za dostop obiščite https://www.sciencedirect.com/science/article/pii/S0272884219321212?via%3Dihub
 PDF - Predstavitvena datoteka, prenos (2,26 MB)
MD5: FA9526B63E2D57E5FE7D38AAD05C9211
|
|---|
| Jezik: | Angleški jezik |
|---|
| Tipologija: | 1.01 - Izvirni znanstveni članek |
|---|
| Organizacija: |  ZAG - Zavod za gradbeništvo Slovenije
|
|---|
| Povzetek: | Alkali-activated materials (AAM) have gained recognition as a promising alternative to technical ceramic and building materials owing to the lower energy demands for production and the potential to use slag as a precursor. In the present study, five sets of slag-based AAM pastes were prepared with different particle sizes (fractions d < 63, 63 < d < 90, and 90 < d < 125 μm in different mass ratios) under the same curing regime and using a fixed precursor to activator (water) mass ratio. Precursors and the hardened AAM are evaluated using BET, XRD, XRF, SEM, FTIR, reactivity of precursors by leaching, and mercury intrusion porosimetry (MIP). Chemical analysis indicated only marginal differences among the different-sized fractions of input materials, whereas the BET surface area and reactivity among the precursors differed significantly-smaller particles had the largest surface area, and thus, higher reactivity. The mineralogical differences between the precursors and hardened AAM were negligible. The results revealed that compressive strength was significantly influenced by particle size, i.e., a threefold increase in strength when the particle size was halved. Microstructural evaluation using MIP confirmed that the porosity was the lowest in AAM with the smallest particle size. The low porosity and high reactivity of the fine fractions led to the highest compressive strength, confirming that manipulation of particle size can significantly influence the mechanical properties. |
|---|
| Ključne besede: | alkalijsko aktivirani materiali, žlindra iz obločne peči, mehanska aktivacija, mehanske lastnosti, poroznost, alkali-activated materials (AAM), electric arc furnace steel slag, mechanical activation, mechanical properties, porosity |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Datum objave: | 26.07.2019 |
|---|
| Založnik: | Ceramurgica s.p.a. |
|---|
| Leto izida: | 2019 |
|---|
| Št. strani: | str. 22632-22641 |
|---|
| Številčenje: | Vol. 45, iss. 17 |
|---|
| PID: | 20.500.12556/DiRROS-17304  |
|---|
| UDK: | 620.1/.2 |
|---|
| ISSN pri članku: | 0272-8842 |
|---|
| DOI: | 10.1016/j.ceramint.2019.07.296 |
|---|
| COBISS.SI-ID: | 2480999 |
|---|
| Avtorske pravice: | © 2019 The Authors. Published by Elsevier Ltd. |
|---|
| Opomba: | E-članek objavljen: 1 December 2019;
|
|---|
| Datum objave v DiRROS: | 22.11.2023 |
|---|
| Število ogledov: | 810 |
|---|
| Število prenosov: | 311 |
|---|
| Metapodatki: |    |
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
