1. |
2. |
3. |
4. Termoplastični kompoziti, ojačani z odpadnimi duroplastičnimi kompoziti : diplomsko deloJernej Leitinger, 2023, diplomsko delo Ključne besede: kompozit, karakterizacija, ABS, termoplastična matrica, UPR, duroplastična armatura, vlaknasta ojačitev, steklena vlakna, mehanske lastnosti, termične lastnosti, diplomsko delo Objavljeno v DiRROS: 28.02.2024; Ogledov: 148; Prenosov: 49 Celotno besedilo (6,17 MB) |
5. Particle size manipulation as an influential parameter in the development of mechanical properties in electric arc furnace slag-based AAMKatja Traven, Mark Češnovar, Vilma Ducman, 2019, izvirni znanstveni članek Povzetek: Alkali-activated materials (AAM) have gained recognition as a promising alternative to technical ceramic and building materials owing to the lower energy demands for production and the potential to use slag as a precursor. In the present study, five sets of slag-based AAM pastes were prepared with different particle sizes (fractions d < 63, 63 < d < 90, and 90 < d < 125 μm in different mass ratios) under the same curing regime and using a fixed precursor to activator (water) mass ratio. Precursors and the hardened AAM are evaluated using BET, XRD, XRF, SEM, FTIR, reactivity of precursors by leaching, and mercury intrusion porosimetry (MIP). Chemical analysis indicated only marginal differences among the different-sized fractions of input materials, whereas the BET surface area and reactivity among the precursors differed significantly-smaller particles had the largest surface area, and thus, higher reactivity. The mineralogical differences between the precursors and hardened AAM were negligible. The results revealed that compressive strength was significantly influenced by particle size, i.e., a threefold increase in strength when the particle size was halved. Microstructural evaluation using MIP confirmed that the porosity was the lowest in AAM with the smallest particle size. The low porosity and high reactivity of the fine fractions led to the highest compressive strength, confirming that manipulation of particle size can significantly influence the mechanical properties. Ključne besede: alkalijsko aktivirani materiali, žlindra iz obločne peči, mehanska aktivacija, mehanske lastnosti, poroznost, alkali-activated materials (AAM), electric arc furnace steel slag, mechanical activation, mechanical properties, porosity Objavljeno v DiRROS: 22.11.2023; Ogledov: 295; Prenosov: 145 Celotno besedilo (2,26 MB) Gradivo ima več datotek! Več... |
6. Vpliv nekaterih drevesnih vrst na mehanske in fizikalne lastnosti ivernih ploščSaša Pirkmaier, Sergej Medved, 1996, izvirni znanstveni članek Povzetek: V prispevku je predsravljen vpliv uporabljenih drevesnih vrst na mehanske in fizikalne lastnosti ivernih plošč. Raziskali smo vpliv spreminjanja deleža smrekovega in bukovega iverja na mehanske in fizikalne lastnosti trislojnih ivernih plošč. Izdelali smo šest različnih variant, pri katerih je bil različen delež smrekovega iverja. Sprememba deleža določene drevesne vrste najbolj vpliva na upogibno trdnost. Zz manjševanjem deleža smrekovega iverja upogibna trdnost pada. Zmanjševanje deleža smrekovega iverja ne vpliva na debelinski nabrek, količino vpite vode, razslojno trdnost, prostorninsko maso in debelino plošč Ključne besede: iverje smreke, iverje bukve, iverna plošča, mehanske in fizikalne lastnosti Objavljeno v DiRROS: 23.08.2023; Ogledov: 367; Prenosov: 101 Celotno besedilo (1,21 MB) |
7. |
8. Optimizacija procesnih parametrov stiskanja termopastičnih materialov : magistrsko deloMarko Rožič, 2022, magistrsko delo Ključne besede: optimizacija procesnih parametrov, vakuumsko stiskanje, hidravlična stiskalnica, termoplastični materiali, simulacije, Autodesk Moldflow Insight (AMI), polietilen (PE), polipropilen (PP), mehanske lastnosti, magistrsko delo Objavljeno v DiRROS: 29.03.2023; Ogledov: 466; Prenosov: 0 Celotno besedilo (3,42 MB) |
9. |
10. |