1. Sliding wear behaviour of conventional and cryotreated PM Cr-V (Vanadis 6) ledeburitic tool steelVenu Yarasu, Peter Jurči, Peter Gogola, Bojan Podgornik, Marko Sedlaček, 2023, izvirni znanstveni članek Ključne besede: cold work tool steel, conventional treatment, cryogenic treatment, hardness, reciprocal sliding, wear
Objavljeno v DiRROS: 08.04.2024; Ogledov: 99; Prenosov: 20
 Celotno besedilo (7,85 MB)
Gradivo ima več datotek! Več... |
2. |
3. Enhancing ductility of hot-work tool steel through isothermal bainitic transformationAnže Bajželj, Aleš Nagode, Tilen Balaško, Barbara Šetina, Jaka Burja, 2024, objavljeni znanstveni prispevek na konferenci Povzetek: Hot-work tool steels are extensively used in industrial applications that require high resistance to mechanical and chemical degradation at elevated temperatures. To meet these requirements, hot-work tool steels must exhibit good mechanical properties, including high tensile strength, hardness, wear resistance, and tempering resistance, as well as high thermal conductivity and ductility. This study investigates the ductility of the hot-work tool steel HTCS-130, which suffers from low ductility due to the presence of stable molybdenum-tungsten carbides (M6C) on the prior austenite crystal grain boundaries. Increasing austenitisation temperatures or prolonging the dwelling time at temperature can promote intensive migration of grain boundaries, leading to negative effects on the mechanical properties of the steel. To address this issue, isothermal transformation in the bainitic area between 350 and 500 °C was performed. Isothermal transformation at around 350 °C leads to the formation of lower bainite, which has similar hardness to tempered martensite. As the temperature of isothermal transformation increases, the hardness of the material decreases, due to the formation of upper bainite. The hardness analysis was measured using the Vickers method, the impact toughness of the steel samples was measured using a Charpy test with V-notched samples. The microstructure characterization was performed using optical and scanning electron microscopy. The improvement of ductility can be achieved by controlling the isothermal transformation of bainite and adjusting the heat treatment conHot-work tool steels are extensively used in industrial applications that require high resistance to mechanical and chemical degradation at elevated temperatures. To meet these requirements, hot-work tool steels must exhibit good mechanical properties, including high tensile strength, hardness, wear resistance, and tempering resistance, as well as high thermal conductivity and ductility. This study investigates the ductility of the hot-work tool steel HTCS-130, which suffers from low ductility due to the presence of stable molybdenum-tungsten carbides (M6C) on the prior austenite crystal grain boundaries. Increasing austenitisation temperatures or prolonging the dwelling time at temperature can promote intensive migration of grain boundaries, leading to negative effects on the mechanical properties of the steel. To address this issue, isothermal transformation in the bainitic area between 350 and 500 °C was performed. Isothermal transformation at around 350 °C leads to the formation of lower bainite, which has similar hardness to tempered martensite. As the temperature of isothermal transformation increases, the hardness of the material decreases, due to the formation of upper bainite. The hardness analysis was measured using the Vickers method, the impact toughness of the steel samples was measured using a Charpy test with V-notched samples. The microstructure characterization was performed using optical and scanning electron microscopy. The improvement of ductility can be achieved by controlling the isothermal transformation of bainite and adjusting the heat treatment conditions. These findings provide useful insights into the design and optimization of heat treatment processes for hot-work tool steels.ditions. These findings provide useful insights into the design and optimization of heat treatment processes for hot-work tool steels.
Ključne besede: hot-work tool steel, austempering, bainitic transformation, ductility, dilatometry
Objavljeno v DiRROS: 28.02.2024; Ogledov: 156; Prenosov: 69
 Celotno besedilo (1,02 MB)
Gradivo ima več datotek! Več... |
4. Effect of heat treatment on thermal conductivity of additively manufactured AISI H13 tool steelSamo Tome, Blaž Karpe, Irena Paulin, Matjaž Godec, 2024, objavljeni znanstveni prispevek na konferenci Povzetek: AISI H13 is commonly used for tooling, where higher wear resistance, thermal fatigue resistance, or hot toughness is required. Such examples include forging dies, plastic molds, hot shear blades, high-pressure die casting, and extrusion dies. Thus, thermal conductivity is one of the most important factors for hot work tools. Typically, the work cycle of a hot work tool designed for forging consists of four main phases: the forging stroke, with which the die imparts its shape onto the part, a brief pause while the die is reset to its original position, a lubrication phase, and a post lubrication dwell phase. During the forging phase, a significant amount of heat is transferred to the die while it is in contact with the part. This heat must then be dispelled for the part to return to a working temperature. While somewhat different, other hot work processes mentioned above are similar in that the hot work tool gets heated to a high temperature due to the contact with the object of deformation. The process of additive manufacturing (AM) promises better, more efficient tool production with features like conforming cooling channels, which would reduce the thermal fatigue of tools, prolonging tool life. However, the powder bed fusion (PBF) method creates a columnar microstructure, which has a detrimental effect on the thermal conductivity of H13 tool steel. Our investigation focused on the beneficial effect of heat treatment, specifically annealing at different temperatures, on the thermal conductivity of AM-produced H13 parts.
Ključne besede: SLM, thermal conductivity, tool steel, heat treatment
Objavljeno v DiRROS: 28.02.2024; Ogledov: 129; Prenosov: 72
Celotno besedilo (655,96 KB)
Gradivo ima več datotek! Več... |
5. Optimizing hot-work tool steel microstructure for enhanced toughnessAnže Bajželj, Tilen Balaško, Barbara Šetina, Jaka Burja, 2024, izvirni znanstveni članek Ključne besede: hot-work tool steel, austempering, bainitic transformation, lower bainite, impact toughness
Objavljeno v DiRROS: 24.01.2024; Ogledov: 215; Prenosov: 93
Celotno besedilo (9,12 MB)
Gradivo ima več datotek! Več... |
