Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Povzetek: Six broadleaf tree species (Celtis australis L. – Mediterranean hackberry, Quercus petraea (Matt.) Liebl. – sessile oak, Fagus sylvatica L. – European beech, Prunus avium L. – wild cherry, Juglans regia L. – Persian walnut and Acer pseudoplatanus L. – sycamore maple) were planted in 2012 in a trial in the Slovenian Karst on two sites differing in productivity to test their suitability for use in the conversion of old pine stands into ecologically more stable broadleaf forests and to investigate their possible response to the harsher growth conditions predicted in the future. The selected economically interesting tree species have higher timber quality than broadleaves which regenerate naturally (e.g., Ostrya carpinifolia, Fraxinus ornus, Quercus cerris). Measurements were taken in 2017, after four growth seasons. All planted species except Fagus sylvatica had a high survival rate. In total, 70% of all seedlings survived, which shows promising potential. The survival rate was higher at the site on flat terrain than at the site on a slope. Prunus avium was the most successful of all planted species in terms of survival rate, at 83%, and other measured parameters (height, height increment, stem diameter, vitality and quality), and Fagus sylvatica was the least successful, with a survival rate of only 20%. Celtis australis had the highest survival rate, at 87%. Acer pseudoplatanus had the largest differences in measured parameters between the more and less productive sites among all planted species. Quercus petraea showed high resistance to xeric conditions and is expected to be the most successful in conversions. All planted species except Fagus sylvatica show favourable initial potential for the future conversion of Karst pine forests.
Ključne besede: forest conversion, broadleaves, survival rate, seedlings quality, climate change
Objavljeno v DiRROS: 28.06.2022; Ogledov: 2192; Prenosov: 987
Datoteka (3,13 MB)

Povzetek: ISO15189:2012 requires medical laboratories to document metrological traceability of their results. While the ISO17511:2003 standard on metrological traceability in laboratory medicine requires the use of the highest available level in the traceability chain, it recognizes that for many measurands there is no reference above the manufacturer's selected measurement procedure and the manufacturer's working calibrator. Some immunoassays, although they intend to measure the same quantity and may even refer to the same reference material, unfortunately produce different results because of differences in analytical selectivity as manufacturers select different epitopes and antibodies for the same analyte. In other cases, the cause is the use of reference materials, which are not commutable. The uncertainty associated with the result is another important aspect in metrological traceability implementation. As the measurement uncertainty on the clinical samples is influenced by the uncertainty of all steps higher in the traceability chain, laboratories should be provided with adequate and appropriate information on the uncertainty of the value assignment to the commercial calibrators that they use. Although the between-lot variation in value assignment will manifest itself as part of the long-term imprecision as estimated by the end-user, information on worst-case to be expected lot-lot variation has to be communicated to the end-user by the IVD provider. When laboratories use ancillary equipment that potentially could have a critical contribution to the reported results, such equipment needs verification of its proper calibration and criticality to the result uncertainty could be assessed by an approach based on risk analysis, which is a key element of ISO15189:2012 anyway. This paper discusses how the requirement for metrological traceability as stated in ISO15189 should be met by the medical laboratory and how this should be assessed by accreditation bodies.
Ključne besede: laboratories, medical laboratory science, risk management, quality control, quality improvement, health care quality assurance, metrological traceability
Objavljeno v DiRROS: 22.10.2020; Ogledov: 1286; Prenosov: 283
Povezava na datoteko

Povzetek: This paper presents the growth potential of sycamore (Acer pseudoplatanus L.) on four types of forest sites located on carbonate bedrock. The research covers sycamore sites (Aceri-Fraxinetum ill.), beech sites (Lamio orvalae-Fagetum), beech sites planted with Norway spruce, and silver fir-beechsites (Omphalodo-Fagetum aceretosum). The analyses for each forest type were carried out on five plots. Our aim was to determine the effect of site factors and stand parameters on sycamore growth. Site productivity (SP) is positively correlated with soil depth, coarse silt percentage in the cambichorizon, the content of phosphorus in leaves and, partly, with potassium. The effect of nitrogen supply on height growth or SP was not confirmed. Furthermore, height growth on sites with a higher rate of nutrient cycling, higher macronutrient supply and higher sand percentage in the cambic horizon is significantly faster. As to the growth of basal area, in addition to positive dependences of crown size, many other correlations with site factors were confirmed.
Ključne besede: beech stand, growing stock, stand value, current volume increment, current value increment, quality structure, social collective
Objavljeno v DiRROS: 12.07.2017; Ogledov: 4473; Prenosov: 1825
Celotno besedilo (185,52 KB)