1. Using bridge weigh-in-motion systems to monitor single-span bridge influence linesAleš Žnidarič, Jan Kalin, 2020, izvirni znanstveni članek Povzetek: Bridge weigh-in-motion systems use instrumented bridges or culverts to weigh vehicles as they pass over the structures. They also provide data to allow the calculation of several bridge performance indicators. The article starts with the basics of a bridge weigh-in-motion system and briefly describes two key bridge performance indicators, girder distribution factor and dynamic amplification factor, which are also derived from B-WIM measurements. The central part of the article focuses on monitoring of influence lines, the third key parameter that characterises the bridge performance under traffic loads. First, the method of calculating the bending moment influence lines from random heavy traffic is described. A coefficient of rotational stiffness is introduced, which defines the shape of influence lines around the supports as a linear combination of the ideal simply supported and fixed supported influence lines, to allow quantifying the influence line changes. Then the long-term monitoring of influence lines is investigated on four different single-span test bridges. The initial focus is given on the examination of the effect of temperature on the shape of influence lines. Finally, two sets of influence lines are compared on one test bridge, one from before and the other from after replacing the expansion joints and bearings. The work done so far confirms that calculating of influence lines from random vehicles with a B-WIM system is entirely feasible and that differences in their shape can be detected on single-span bridges. What remains to be investigated is the comparison of these differences to the actual damages and under which circumstances the proposed procedure can compete with or better the routine bridge inspection and the conventional monitoring techniques.
Ključne besede: bridge loading, bridge response, temperature dependency, influence line, monitoring
Objavljeno v DiRROS: 12.09.2023; Ogledov: 348; Prenosov: 132
 Celotno besedilo (2,38 MB)
Gradivo ima več datotek! Več... |
2. Measurements of bridge dynamic amplification factor using bridge weigh-in-motion dataJan Kalin, Aleš Žnidarič, Andrej Anžlin, Maja Kreslin, 2022, izvirni znanstveni članek Povzetek: The dynamic component of bridge traffic loading is commonly taken into account with a Dynamic Amplification Factor (DAF)—the ratio between the dynamic and static load effects on a bridge. In the design codes, this factor is generally more conservative than in reality. Recently a new method of cal- culation of this factor had been developed. Data from 15 different bridges have been analysed since then and this paper presents the results of the analyses. The background for Bridge Weigh-in-Motion is given, and the most recent method for DAF calculation is described. The sites from which the data originated are presented, and the selection of data discussed. The results of the analyses are presented and discussed and some examples of DAF calculations are shown. Data from the considered sites have invariably demonstrated a DAF decrease with increasing axle load. This is a significant result, especially for assessment of existing structures, since it is beneficial to use measured structural param- eters to optimise structural analysis.
Ključne besede: bridge loads, bridge weigh-in-motion, dynamic amplication factor, dynamic analysis, measurement, traffic loading
Objavljeno v DiRROS: 14.07.2023; Ogledov: 289; Prenosov: 156
Celotno besedilo (2,61 MB)
Gradivo ima več datotek! Več... |
3. Development and testing of a railway bridge weigh-in-motion systemDonya Hajializadeh, Aleš Žnidarič, Jan Kalin, Eugene J. OBrien, 2020, izvirni znanstveni članek Povzetek: This study describes the development and testing of a railway bridge weigh-in-motion (RB-WIM) system. The traditional bridge WIM (B-WIM) system developed for road bridges was extended here to calculate the weights of railway carriages. The system was tested using the measured response from a test bridge in Poland, and the accuracy of the system was assessed using statically-weighed trains. To accommodate variable velocity of the trains, the standard B-WIM algorithm, which assumes a constant velocity during the passage of a vehicle, was adjusted and the algorithm revised accordingly. The results showed that the vast majority of the calculated carriage weights fell within %5% of their true, statically-weighed values. The sensitivity of the method to the calibration methods was then assessed using regression models, trained by di%erent combinations of calibration trains.
Ključne besede: bridge weigh-in-motion, railway bridge loading, bridge instrumentation, B-WIM
Objavljeno v DiRROS: 22.05.2023; Ogledov: 299; Prenosov: 149
Celotno besedilo (6,18 MB)
Gradivo ima več datotek! Več... |
