1. Comprehensive permanent remote monitoring system of a multi-span highway bridgeAndrej Anžlin, Uroš Bohinc, Doron Hekič, Maja Kreslin, Jan Kalin, Aleš Žnidarič, 2021, objavljeni znanstveni prispevek na konferenci Povzetek: As part of the reconstruction of a multi-span viaduct on a Slovenian highway, a permanent remote monitoring system with over 200 sensors was established. Several parameters are monitored on different parts of the viaduct by means of temperature sensors, accelerometers, strain gauges, long-gauge deformation and Fibre Bragg Grating (FBG) sensors. In this way strains, frequencies and temperatures on external prestressed beam cables, carbon fibre rebarsused for the flexural strengthening of a deck overhang, pier caps and prestressed beams are measured and stored into the on-site central data acquisition system. This paper presents architecture of the permanent bridge monitoring system and preliminary results of the measurements.
Ključne besede: permanent monitoring, structural health monitoring, bridge WIM, sensors, viaduct
Objavljeno v DiRROS: 22.01.2024; Ogledov: 240; Prenosov: 112
 Celotno besedilo (9,29 MB)
Gradivo ima več datotek! Več... |
2. Using statistical analysis of an acceleration-based bridge weigh-in-motion system for damage detectionEugene J. O'Brien, Muhammad Arslan Khan, Daniel Patrick McCrum, Aleš Žnidarič, 2020, izvirni znanstveni članek Povzetek: This paper develops a novel method of bridge damage detection using statistical analysis of data from an acceleration-based bridge weigh-in-motion (BWIM) system. Bridge dynamic analysis using a vehicle-bridge interaction model is carried out to obtain bridge accelerations, and the BWIM concept is applied to infer the vehicle axle weights. A large volume of traffic data tends to remain consistent (e.g., most frequent gross vehicle weight (GVW) of 3-axle trucks); therefore, the statistical properties of inferred vehicle weights are used to develop a bridge damage detection technique. Global change of bridge stiffness due to a change in the elastic modulus of concrete is used as a proxy of bridge damage. This approach has the advantage of overcoming the variability in acceleration signals due to the wide variety of source excitations/vehicles–data from a large number of different vehicles can be easily combined in the form of inferred vehicle weight. One year of experimental data from a short-span reinforced concrete bridge in Slovenia is used to assess the effectiveness of the new approach. Although the acceleration-based BWIM system is inaccurate for finding vehicle axle-weights, it is found to be effective in detecting damage using statistical analysis. It is shown through simulation as well as by experimental analysis that a significant change in the statistical properties of the inferred BWIM data results from changes in the bridge condition.
Ključne besede: bridge health monitoring, bridge WIM, structural dynamics, damage detection, vehicle-bridge interaction
Objavljeno v DiRROS: 12.09.2023; Ogledov: 277; Prenosov: 139
Celotno besedilo (8,01 MB)
Gradivo ima več datotek! Več... |
3. Model updating concept using bridge Weigh-in-Motion dataDoron Hekič, Andrej Anžlin, Maja Kreslin, Aleš Žnidarič, Peter Češarek, 2023, izvirni znanstveni članek Povzetek: Finite element (FE) model updating of bridges is based on the measured modal parameters and less frequently on the measured structural response under a known load. Until recently, the FE model updating did not consider strain measurements from sensors installed for weighing vehicles with bridge weigh-in-motion (B-WIM) systems. A 50-year-old multi-span concrete highway viaduct, renovated between 2017 and 2019, was equipped with continuous monitoring system with over 200 sensors, and a B-WIM system. In the most heavily instrumented span, the maximum measured longitudinal strains induced by the full-speed calibration vehicle passages were compared with the modelled strains. Based on the sensitivity study results, three variables that affected its overall stiffness were updated: Young’s modulus adjustment factor of all structural elements, and two anchorage reduction factors that considered the interaction between the superstructure and non-structural elements. The analysis confirmed the importance of the initial manual FE model updating to correctly reflect the non-structural elements during the automatic nonlinear optimisation. It also demonstrated a successful use of pseudo-static B-WIM loading data during the model updating process and the potential to extend the proposed approach to using random B-WIM-weighed vehicles for FE model updating and long-term monitoring of structural parameters and load-dependent phenomena.
Ključne besede: monitoring, bridge, viaduct, bridge weigh-in-motion (B-WIM), structural health monitoring (SHM), finite element (FE), calibration, model updating
Objavljeno v DiRROS: 29.05.2023; Ogledov: 402; Prenosov: 221
Celotno besedilo (26,28 MB)
Gradivo ima več datotek! Več... |
