Digitalni repozitorij raziskovalnih organizacij Slovenije

Izpis gradiva
A+ | A- | Pomoč | SLO | ENG

Naslov:AISI H13 tool steel - comparison between powder bed fused and classically produced parts
Avtorji:ID Tome, Samo (Avtor)
ID Paulin, Irena (Avtor)
ID Godec, Matjaž (Avtor)
Datoteke:.pdf PDF - Predstavitvena datoteka, prenos (595,24 KB)
MD5: 41C24ACAD20E75740A1608ADB1CB0185
 
URL URL - Izvorni URL, za dostop obiščite https://www.confer.cz/metal/2024/4881-aisi-h13-tool-steel-comparison-between-powder-bed-fused-and-conventionally-produced-parts
 
Jezik:Angleški jezik
Tipologija:1.08 - Objavljeni znanstveni prispevek na konferenci
Organizacija:Logo IMT - Inštitut za kovinske materiale in tehnologije
Povzetek:AISI H13 Is very commonly used in the hot-work category of steels. Whether it is used as a forging die, a hotcutting tool, or a mold in injection molding or die casting, it is always on the table, as the material of choice. However, its potential has not yet been fully realized. New manufacturing techniques such as additive manufacturing (AM) broaden the horizon of the material’s application, and promise improved performance, through optimized geometry, unobtainable by traditional means, and heightened mechanical properties. One of the more widespread AM processes is Powder Bed Fusion (PBF) where a laser or electron beam constructs the model, by meting a thin coating of metal powder applied to a base plate. By repeatedly applying and melting powder, the end result is a layer-by-layer produced part. However, the techniques for producing such parts are not yet refined enough and require further research. Problems like porosities, part deflection, and crack formation due to residual stress are commonplace, while comparably low mechanical properties in the asprocessed state call for post-production treatments. Naturally, every technique has its boons and drawbacks, and that is what this work aims to analyze - How do the PBF parts compare to classically produced ones, and what are the difficulties in producing the later-mentioned parts.
Ključne besede:powder bed fusion, tool steel, additive manufacturing, mechanical properties
Status publikacije:Objavljeno
Verzija publikacije:Objavljena publikacija
Datum objave:02.12.2024
Založnik:TANGER
Leto izida:2024
Št. strani:Str. 166-171
Izvor:Češka
PID:20.500.12556/DiRROS-21211 Novo okno
UDK:669.14
ISSN pri članku:2694-9296
DOI:10.37904/metal.2024.4881 Novo okno
COBISS.SI-ID:222574339 Novo okno
Avtorske pravice:Licenca Creative Commons je navedena na pristajalni strani članka (glej izvorni URL): "© This is an open access article distributed under the Creative Commons Attribution License (https://creativecommons.org/licenses/by/4.0/)". (Datum opombe 16. 1. 2025)
Opomba:Nasl. z nasl. zaslona; Opis vira z dne 15. 1. 2025;
Datum objave v DiRROS:16.01.2025
Število ogledov:238
Število prenosov:111
Metapodatki:XML DC-XML DC-RDF
:
TOME, Samo, PAULIN, Irena in GODEC, Matjaž, 2024, AISI H13 tool steel - comparison between powder bed fused and classically produced parts. V : Metal 2024 [na spletu]. Objavljeni znanstveni prispevek na konferenci. Češka : TANGER. 2024. p. 166–171. [Dostopano 9 april 2025]. Pridobljeno s: https://dirros.openscience.si/IzpisGradiva.php?lang=slv&id=21211
Kopiraj citat
  
Objavi na:Bookmark and Share


Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše podrobnosti ali sproži prenos.

Gradivo je del zbornika

Naslov:Metal 2024
COBISS.SI-ID:222557443 Novo okno

Gradivo je del revije

Naslov:Metal ...
Skrajšan naslov:Metal
Založnik:Tanger s.r.o.
ISSN:2694-9296
COBISS.SI-ID:128396547 Novo okno

Gradivo je financirano iz projekta

Financer:ARIS - Javna agencija za znanstvenoraziskovalno in inovacijsko dejavnost Republike Slovenije
Številka projekta:P2-0132
Naslov:Fizika in kemija površin kovinskih materialov
Financer:ARIS - Javna agencija za znanstvenoraziskovalno in inovacijsko dejavnost Republike Slovenije
Številka projekta:L2-2613
Naslov:Novi kompozitni materiali s kovinsko matrico, ojačano z nanodelci ter izdelani s selektivnim laserskim taljenjem za aplikacije v orodjarstvu

Licence

Licenca:CC BY 4.0, Creative Commons Priznanje avtorstva 4.0 Mednarodna
Povezava:http://creativecommons.org/licenses/by/4.0/deed.sl
Opis:To je standardna licenca Creative Commons, ki daje uporabnikom največ možnosti za nadaljnjo uporabo dela, pri čemer morajo navesti avtorja.

Nazaj