| Naslov: | Ladle melt treatment of high sulfur stainless steels |
|---|
| Avtorji: | ID Burja, Jaka (Avtor) |
|---|
| Datoteke: |  PDF - Predstavitvena datoteka, prenos (526,82 KB)
MD5: 99EC867C4028898A42D5D25C70313627
 URL - Izvorni URL, za dostop obiščite https://www.confer.cz/metal/2023/4627-ladle-melt-treatment-of-high-sulfur-stainless-steels
|
|---|
| Jezik: | Angleški jezik |
|---|
| Tipologija: | 1.08 - Objavljeni znanstveni prispevek na konferenci |
|---|
| Organizacija: |  IMT - Inštitut za kovinske materiale in tehnologije
|
|---|
| Povzetek: | The influence of sulfur on both slag and melt is very important in steelmaking. This is especially true for highsulfur machining steels. Machinability is achieved by alloying high sulfur contents, above 300 ppm. These are steels that form small chips and shavings during mechanical processing by cutting, which is more appropriate and favorable for both the workpiece and the processing tool and machine. However, the secondary steelmaking slag is typically designed for desulfurization. This means that the sulfur content rapidly falls after sulfur additions. This is especially true for high machinability stainless steel grades where S contents can exceed 1000 ppm. This causes the sulfur wire yield to vary greatly in each charge, making the process unreliable. Some aspects of understanding the interaction between the steel melt and slag and the effect on casting are presented in this work. Based on industrial charges, we analyzed the yield of sulfur additions and the influencing factors on the efficiency of the sulfur addition. The lower slag basicity was linked to lover sulfur distribution rations, and lover sulfur distribution rations were linked to higher sulfur yields. Melt and slag samples were analyzed. Slag entrapment during ingot casting was linked to the high sulfur contents. |
|---|
| Ključne besede: | desulfurization, sulfur, stainless steel, steelmaking |
|---|
| Status publikacije: | Objavljeno |
|---|
| Verzija publikacije: | Objavljena publikacija |
|---|
| Založnik: | TANGER |
|---|
| Leto izida: | 2024 |
|---|
| Št. strani: | Str. 33-37 |
|---|
| Izvor: | Češka |
|---|
| PID: | 20.500.12556/DiRROS-18289  |
|---|
| UDK: | 669.1 |
|---|
| ISSN pri članku: | 2694-9296 |
|---|
| DOI: | 10.37904/metal.2023.4627 |
|---|
| COBISS.SI-ID: | 186843651 |
|---|
| Avtorske pravice: | Licenca Creative Commons je navedena na pristajalni strani članka (glej izvorni URL): "© This is an open access article distributed under the Creative Commons Attribution License (https://creativecommons.org/licenses/by/4.0/)". (Datum opombe 4. 4. 2023) |
|---|
| Opomba: | Nasl. z nasl. zaslona;
Opis vira z dne 27. 2. 2024;
|
|---|
| Datum objave v DiRROS: | 28.02.2024 |
|---|
| Število ogledov: | 523 |
|---|
| Število prenosov: | 221 |
|---|
| Metapodatki: |    |
|---|
|
:
|
Kopiraj citat |
|---|
| | | | Objavi na: |  |
|---|
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše
podrobnosti ali sproži prenos. |
