Digital repository of Slovenian research organisations

Search the repository
A+ | A- | Help | SLO | ENG

Query: search in
search in
search in
search in

Options:
  Reset


Query: "author" (��mitek Andrej) .

81 - 90 / 433
First pagePrevious page567891011121314Next pageLast page
81.
82.
83.
Effects of the temperature on the pore evolution during sintering of the belite-sulfoaluminate cement clinker using x-ray computed microtomography
Sabina Dolenec, Lidija Korat, Maruša Mrak, Andrej Ipavec, Lea Žibret, 2020, original scientific article

Abstract: In this paper, the effects of the sintering temperature on the pore evolution of the belite-sulfoaluminate cement clinker were evaluated. Belite-sulfoaluminate cement clinker with a targeted composition of 65 w/% b-belite, 20 w/% calcium sulfoaluminate and 10 w/% ferrite was sintered at three different temperatures: 1200 °C, 1250 °C and 1300 °C. To quantitatively evaluate the pore evolution during sintering, a 3D microstructure reconstruction by micro-CT was used. From the data, the pore volume frac- tion and pore number were extracted and compared, and the pore size distribution with the sintering temperature was obtained as well. Additionally, the pore shape and distribution were displayed in 3D based on actual microstructure data. Clinker samples were also characterized by Hg-intrusion porosimetry and gas sorption. The changes in the pore evolution occurred to a larger extent when sintering at 1300 °C. Apart from a significant porosity decrease, pore coarsening was evident at this temperature, reducing their connectivity and shrinkage of the clinker. Simultaneously, the bulk and apparent densities increased with the temperature due to densification, while the BET surface area of the studied clinkers decreased, indicating the rounding of pores and particle coalescence with an increasing grain growth.
Keywords: klinker, belit-sulfoaluminat, razvoj por, sintranje
Published in DiRROS: 04.08.2023; Views: 315; Downloads: 136
.pdf Full text (2,27 MB)
This document has many files! More...

84.
85.
86.
Measurements of bridge dynamic amplification factor using bridge weigh-in-motion data
Jan Kalin, Aleš Žnidarič, Andrej Anžlin, Maja Kreslin, 2022, original scientific article

Abstract: The dynamic component of bridge traffic loading is commonly taken into account with a Dynamic Amplification Factor (DAF)—the ratio between the dynamic and static load effects on a bridge. In the design codes, this factor is generally more conservative than in reality. Recently a new method of cal- culation of this factor had been developed. Data from 15 different bridges have been analysed since then and this paper presents the results of the analyses. The background for Bridge Weigh-in-Motion is given, and the most recent method for DAF calculation is described. The sites from which the data originated are presented, and the selection of data discussed. The results of the analyses are presented and discussed and some examples of DAF calculations are shown. Data from the considered sites have invariably demonstrated a DAF decrease with increasing axle load. This is a significant result, especially for assessment of existing structures, since it is beneficial to use measured structural param- eters to optimise structural analysis.
Keywords: bridge loads, bridge weigh-in-motion, dynamic amplication factor, dynamic analysis, measurement, traffic loading
Published in DiRROS: 14.07.2023; Views: 290; Downloads: 156
.pdf Full text (2,61 MB)
This document has many files! More...

87.
Microstructural characteristics of belite–sulfoaluminate cement clinkers with bottom ash
Lea Žibret, Andrej Ipavec, Sabina Dolenec, 2022, original scientific article

Abstract: The incorporation mechanism of impurities derived from raw materials into a belite-sulfoaluminate cement clinker with bottom ash was investigated in two raw mixtures. Alkalis lowered the sintering temperature by 50 °C. Ti stabilized β belite and prevented the formation of γ-belite. Sodalite solid solution showed an incomplete substitution of Si by Al. At a higher Ti content ferrite solid solution trended towards perovskite composition. Although calcium sulfoaluminate only fully developted at 1300 °C, the clinkers sintered at 1200 °C were the most reactive, as the presence of anhydrite at 1200 °C accelerated early hydration. Clinker reactivity decreased with an increase in sintering temperature.
Keywords: BSCA clinker, belite, calcium sulfoaluminate, secondary raw materials, microstructure, reactivity
Published in DiRROS: 03.07.2023; Views: 399; Downloads: 188
.pdf Full text (8,39 MB)
This document has many files! More...

88.
89.
Phytosociological description of the dwarf mountain pine shrub community (Amelanchiero ovalis-Pinetum mugo) in the valleys of the Slovenian Alps
Igor Dakskobler, Mateja Cojzer, Andrej Rozman, 2023, original scientific article

Abstract: We have expanded our knowledge of the localities, sites and distribution of the Amelanchiero ovalis-Pinetum mugo association in the Slovenian Alps. Based on phytocenological analyses, the shrub association belonging to the forest vegetation type Alpine mountain pine scrub was divided into two subassociations: peucedanetosum oreoselini and hylocomiadelphetosum triquetri. We also described four variants within the latter association.
Keywords: phytosociology, synsystematics, Pinus mugo, Natura 2000, Triglav National Park, Topla Landscape Park, Slovenia
Published in DiRROS: 27.06.2023; Views: 1105; Downloads: 494
.pdf Full text (6,58 MB)
This document has many files! More...

90.
Razvoj in karakterizacija mišjega modela za študije HPV-pozitivnega raka glave in vratu
Živa Modic, Maja Čemažar, Boštjan Markelc, Andrej Cör, Gregor Serša, Simona Kranjc Brezar, Tanja Jesenko, 2023, published scientific conference contribution abstract

Keywords: miši, rak glave in vratu, gensko zdravljenje
Published in DiRROS: 19.06.2023; Views: 360; Downloads: 159
.pdf Full text (361,47 KB)
This document has many files! More...

Search done in 0.35 sec.
Back to top