81. Effects of variated final temperature and workpiece thickness for hot rolling of aluminum alloy EN AW-8011Jakob Kraner, Peter Cvahte, Primož Šuštarič, Tomaž Šuštar, Črtomir Donik, Irena Paulin, Shae K. Kim, Kjung Il Kim, 2023, izvirni znanstveni članek Ključne besede: aluminum alloy, hot rolling, simulations, metallography, mechanical properties Objavljeno v DiRROS: 01.02.2024; Ogledov: 151; Prenosov: 81 Celotno besedilo (5,46 MB) Gradivo ima več datotek! Več... |
82. Influence of boron and nitrogen on the machinability, polishability and wear of martensitic stainless steelsMarko Sedlaček, Barbara Šetina, Vesna Žepič Bogataj, Jaka Burja, 2023, izvirni znanstveni članek Ključne besede: martensitic stainless steel, boron, nitrogen, wear, machinability, polishability Objavljeno v DiRROS: 01.02.2024; Ogledov: 155; Prenosov: 81 Celotno besedilo (7,53 MB) Gradivo ima več datotek! Več... |
83. Ultra-high strenght TWIP steel with high chromium contentPavel Podaný, Tomáš Studecký, Tomas Gregor, Radek Prochazka, Aleksandra Kocijan, 2023, izvirni znanstveni članek Povzetek: A new ultra-high strength steel with a fully austenitic microstructure and twinning-induced plasticity (TWIP) effect has been developed. TWIP effect gives this steel a good combination of high strength of over 1000 MPa and ductility of over 35%. This new steel has a high chromium content, which increases its corrosion resistance. By combining cold rolling and annealing, the steel has achieved a very fine austenitic microstructure with an average grain diameter of 2.85 µm. This steel could be used for structural applications or components that need to withstand high levels of stress, deformation and corrosion environment. Ključne besede: TWIP steels, corrosion resistance, microstructure, tensile strength, plasticity Objavljeno v DiRROS: 31.01.2024; Ogledov: 202; Prenosov: 84 Povezava na datoteko Gradivo ima več datotek! Več... |
84. Improving the surface properties of additive-manufactured Inconel 625 by plasma nitridingDanijela Anica Skobir Balantič, Črtomir Donik, Bojan Podgornik, Aleksandra Kocijan, Matjaž Godec, 2023, izvirni znanstveni članek Povzetek: As a surface-hardening technique, plasma nitriding is a common procedure for improving the properties of
conventional Ni-based alloys. The diffusion of nitrogen hardens a layer on the surface of the alloy, leading to
better wear resistance and a higher coefficient of friction, as well as a higher surface hardness. This study reports
the effect of plasma nitriding on additive-manufactured (AM) Inconel 625 (IN625) compared to its conventional
manufactured and nitrided counterparts. The samples produced with the laser powder-bed fusion (LPBF) process
were subsequently plasma nitrided in the as-built condition, stress-relief annealed at 870 °C and solution treated
at 1050 °C. The plasma nitridings were carried out at 430 °C and 500 °C for 15 h. The growth kinetics of the
nitride layer of the AM samples depends on the prior heat treatments and is faster in the as-built state due to the
specific cellular structure. The lower nitriding temperature leads to the formation of expanded austenite in the
nitride layer, while at the higher nitriding temperature, the expanded austenite decomposes and CrN precipitation
occurs. The XRD and SEM analyses confirmed the presence of two layers: the surface layer and the
diffusion layer beneath. The lower nitriding temperature caused the formation of expanded austenite or a
combination of expanded austenite and CrN. The higher nitriding temperature led to the decomposition of the
expanded austenite and to the formation/precipitation of CrN. The higher nitriding temperature also decreased
the corrosion resistance slightly due to the increased number of precipitated Cr-nitrides. On the other hand, the
wear resistance was significantly improved after plasma nitriding and was much less influenced by the nitriding
temperature. Ključne besede: additive manufacturing, powder-bed fusion, plasma nitriding, expanded austenite, wear and corrosion resistance, Ni-based alloy Objavljeno v DiRROS: 31.01.2024; Ogledov: 189; Prenosov: 80 Celotno besedilo (7,98 MB) Gradivo ima več datotek! Več... |
85. Relevance of inter-particle interaction in directed energy deposition powder streamTijan Mede, Matjaž Godec, 2024, izvirni znanstveni članek Povzetek: Blown powder dynamics is one of the aspects of Directed Energy Deposition (DED) with a major influence on deposition quality and potential for improvement in simulation. Most currently employed computational models discard powder grain collisions as negligible, although little explicit evidence for that claim exists. A Discrete Element Method approach is thus employed in the present work to simulate the actual number of grain collisions in a powder stream of a commercial discrete coaxial nozzle and how that number varies with the key processing parameters. While the number of powder grain collisions is found to in fact be negligible at one side of the usable parameter spectrum, the opposite side results in as many as 84% of all the powder grains being involved in inter-granular collisions with an average rebound angle of 14◦, challenging the established hypothesis of the negligibility of this phenomena. Ključne besede: DED, powder stream, grain collisions, DEM Objavljeno v DiRROS: 31.01.2024; Ogledov: 117; Prenosov: 67 Celotno besedilo (1,65 MB) Gradivo ima več datotek! Več... |
86. High-temperature oxidation of boiler steels at 650 °CJaka Burja, Barbara Šetina, Borut Žužek, Tilen Balaško, 2023, izvirni znanstveni članek Povzetek: This study presents a comprehensive investigation of the formation, composition and
behaviour of oxide layers during the high-temperature oxidation of four different steel alloys (16Mo3,
13Cr, T24 and P91) at a uniform temperature of 650 °C. The study is aimed at assessing the oxidation
damage due to short-term overheating. The research combines CALPHAD (CALculation of PHAse
Diagrams) calculations, thermogravimetric analysis (TGA) and advanced microscopy techniques, in-
cluding scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), to elucidate
the complex mechanisms controlling oxidation kinetics and oxide layer development. CALPHAD
calculations were used to determine the thermodynamically stable phases for each steel type at 650
◦C and different oxygen activities. The results showed different phase compositions, highlighting
the importance of the chromium content in steel for the formation of oxide layers. The different
oxidation kinetics and oxide layer compositions are presented and associated with the increased risk
of material degradation due to overheating. These results have significant implications for industrial
applications, mainly the susceptibility to oxidation of low-alloyed steels like 16Mo3 and 13 Cr and
contribute to a deeper understanding of oxidation processes in steels. Ključne besede: high-temperature oxidation, thermogravimetric analysis, kinetics, CALPHAD, boiler steels, SEM, EBSD Objavljeno v DiRROS: 26.01.2024; Ogledov: 238; Prenosov: 114 Celotno besedilo (12,99 MB) Gradivo ima več datotek! Več... |
87. Morphological characteristics of young and old murine hematopoietic stem cell niches, as modeled in vitroMojca Justin, Ema Rogac Randl, Veno Kononenko, Matej Hočevar, Damjana Drobne, Primož Rožman, 2023, izvirni znanstveni članek Povzetek: The hematopoietic stem cell (HSC) niche undergoes detrimental changes with age. The molecular differences between young and
old niches are well studied and understood; however, young and old niches have not yet been extensively characterized in terms of
morphology. In the present work, a 2D stromal model of young and old HSC niches isolated from bone marrow was investigated
using light and scanning electron microscopy (SEM) to characterize cell density after one, two, or three weeks of culturing, cell
shape, and cell surface morphological features. Our work is aimed at identifying morphological differences between young and
old niche cells that could be used to discriminate between their respective murine HSC niches. The results show several age-
specific morphological characteristics. The old niches differ from the young ones in terms of lower cell proliferating capacity,
increased cell size with a flattened appearance, increased number of adipocytes, and the presence of tunneling nanotubes. In
addition, proliferating cell clusters are present in the young niches but not in the old niches. Together, these characteristics
could be used as a relatively simple and reliable tool to discriminate between young and old murine HSC niches and as a
complementary approach to imaging with specific cellular markers. Ključne besede: bone marrow, hematoopetic stem cell niche, aging, adipocytes, scanning electron microscopy Objavljeno v DiRROS: 26.01.2024; Ogledov: 214; Prenosov: 107 Celotno besedilo (2,47 MB) Gradivo ima več datotek! Več... |
88. High temperature friction and galling properties of nanolayered (Cr,V)N coatings and effect of V contentBojan Podgornik, Marko Sedlaček, Barbara Šetina, Miha Čekada, 2023, izvirni znanstveni članek Ključne besede: (Cr, V)N coating, galling, high-temperature tribology, hot forming, self-lubrication Objavljeno v DiRROS: 26.01.2024; Ogledov: 211; Prenosov: 130 Celotno besedilo (12,53 MB) Gradivo ima več datotek! Več... |
89. Autologous platelet and extracellular vesicle-rich plasma as therapeutic fluid : a reviewKaja Troha, Domen Vozel, Matevž Arko, Apolonija Bedina Zavec, Drago Dolinar, Matej Hočevar, Zala Jan, Matic Kisovec, Boštjan Kocjančič, Ljubiša Pađen, Manca Pajnič, Samo Penič, Anna Romolo, Neža Repar, Vesna Spasovski, Nejc Steiner, Vid Šuštar, Aleš Iglič, Damjana Drobne, Ksenija Kogej, Saba Battelino, Veronika Kralj-Iglič, 2023, pregledni znanstveni članek Ključne besede: platelet-rich plasma, platelets, centrifugation, extracellular vesicles, small cellular particles, wound healing, regeneration, fresh-frozen plasma, intercellular signaling peptides and proteins Objavljeno v DiRROS: 26.01.2024; Ogledov: 240; Prenosov: 121 Celotno besedilo (2,37 MB) Gradivo ima več datotek! Več... |
90. Evaluation and metrological performance of a novel ionisation vacuum gauge suitable as reference standardKarl Jousten, Sylke Bechstein, Matthias Bernien, Frédéric Boineau, N. Bundaleski, Claus Illgen, Berthold Jenninger, Janez Šetina, Ricardo A. S. Silva, Anke Stöltzel, O. M. N. D. Teodoro, Martin Wüest, 2023, izvirni znanstveni članek Ključne besede: ionisation vacuum gauge, hot cathode, sensitivity, secondary electrons, ion induced secondary electron yield Objavljeno v DiRROS: 26.01.2024; Ogledov: 212; Prenosov: 95 Celotno besedilo (3,39 MB) Gradivo ima več datotek! Več... |