1. Thermal characterisation of the cooling phase of post-flashover compartment firesAndrea Lucherini, Balša Jovanović, Jose L. Torero, Ruben Van Coile, Bart Merci, 2024, izvirni znanstveni članek Povzetek: The main characteristics of the cooling phase of post-flashover compartment fires are studied using a simplified first-principles heat transfer approach to establish key limitations of more traditional methodologies (e.g., Eurocode). To this purpose, the boundary conditions during cooling are analysed. To illustrate the importance of a first-principles approach, a detailed review of the literature is presented followed by the presentation of a simplified numerical model. The model is constructed to calculate first-order thermal conditions during the cooling phase. The model is not intended to provide a precise calculation method but rather baseline estimates that incorporate all key thermal inputs and outputs. First, the thermal boundary conditions in the heating phase are approximated with a single (gas) temperature and the Eurocode parametric fire curves, to provide a consistent initial condition for the cooling phase and to be able to compare the traditional approach to the first- principles approach. After fuel burnout, the compartment gases become optically thin and temperatures decay to ambient values, while the compartment solid elements slowly cool down. For simplicity, convective cooling of the compartment linings is estimated using a constant convective heat transfer coefficient and all linings surfaces are assumed to have the same temperature (no net radiative heat exchange). All structural elements are assumed to be thermally thick. While these simplifications introduce quantitative errors, they enable an analytical solution for transient heat conduction in a semi-infinite solid that captures all key heat transfer processes. Comparisons between the results obtained using both approaches highlight how, even when considering the same fire energy input, the thermal boundary conditions according to the Eurocode parametric fire curves lead to an increase energy accumulated in the solid after fuel burnout and a delay in the onset of cooling. This is not physically correct, and it may lead to misrepresentation of the impact of post-flashover fires on structural behaviour.
Ključne besede: cooling phase, fire decay, fire dynamics, compartment fires, structural fire engineering, fire safety
Objavljeno v DiRROS: 15.04.2024; Ogledov: 56; Prenosov: 28
 Celotno besedilo (6,40 MB)
Gradivo ima več datotek! Več... |
2. A meshless numerical solution of thermo-mechanics of hot-rolled steel bars on a cooling bedGašper Vuga, Boštjan Mavrič, Umut Hanoglu, Božidar Šarler, 2023, objavljeni znanstveni prispevek na konferenci Povzetek: After the continuous hot-rolling process, steel bars are immediately placed on the cooling bed. At the beginning of the cooling, the material is at high temperatures, and the yield strength is low. Due to thermal load, yield strength can be exceeded, and permanent plastic strains start accumulating, resulting in possible unwanted shape changes and residual stresses. The present paper aims to develop a thermo-mechanical model for studying and eliminating undesirable phenomena before the products leave the cooling bed. The governing equations are solved for the two-dimensional slice in a strong form, and a modified version of the radial basis function generated finite difference (RBF-FD) method [1]. The initial bar geometry is obtained from the existing meshless hot-rolling simulation system [2]. The thermal and mechanical models are one-way coupled, i.e. the temperature solution represents a driving force for the stress and strain solution. The temperature field is obtained with explicit propagation in time. The convective and radiative heat fluxes on the boundary are updated at each time step using the ray tracing procedure to determine the radiative heat flux. The mechanical part is solved by considering the small strain elasto-plasticity, where the isotropic von Mises temperature-dependent hardening is employed. The global system of nonlinear equations of the mechanical part is solved by the Newton-Raphson method. The closest point projection method is used to solve the constitutive relations. A sensitivity study is performed on the influence of cooling intensity on a rectangular steel bar’s temperature, stress and strain field. We defined the most influential factors for defect formation. For the first time, a novel meshless RBF-FD method is successfully used for solving such a complex industrial problem. The model will be perspectively upgraded from the slice to the three-dimensional model to enable also bending.
Ključne besede: cooling bed, steel bars, thermo-mechanics, strong form, meshless method
Objavljeno v DiRROS: 21.03.2024; Ogledov: 67; Prenosov: 40
Celotno besedilo (1,62 MB)
Gradivo ima več datotek! Več... |
3. Influence of geology, hydrogeology, and climate on ground source heat pump distribution in Slovenia and selected European countriesSimona Adrinek, Mitja Janža, Rao Martand Singh, 2024, izvirni znanstveni članek Povzetek: Shallow geothermal energy (SGE) is a renewable energy that could contribute to the decarbonatization of the heating and cooling sector. SGE is predominantly harnessed through ground source heat pump (GSHP) systems. The choice of which type of GSHP system depends on various factors. Understanding these factors is crucial for optimizing the efficiency of GSHP systems and fostering their implementation. In this paper, we have analysed the spatial distribution of GSHPs in Slovenia. We identified 1073 groundwater and 1122 ground-coupled heat pump systems with a total heat pump capacity of almost 30 MW. We quantitatively assessed the influence of geological, hydrogeological, and climate conditions on their spatial distribution. Using the χ2 test and information value method, we identified hydrogeological conditions as the most influential factor for the GSHP systems’ spatial distribution. We also performed the spatial analysis of geological and hydrogeological data in 22 European countries, including Slovenia. We collected the reported numbers of installed GSHP units in 2020 and were able to distinguish the shares of groundwater and ground-coupled heat pump systems for 12 of these countries. The analysis showed that ground-coupled heat pumps predominate in most countries, even if the natural conditions are favourable for groundwater heat pumps.
Ključne besede: shallow geothermal energy, renewable heating and cooling, ground-source heat pump, spatial distribution, natural condition
Objavljeno v DiRROS: 19.03.2024; Ogledov: 74; Prenosov: 39
Celotno besedilo (15,39 MB) |
|
