1. Understanding carbide evolution and surface chemistry during deep cryogenic treatment in high-alloyed ferrous alloyPatricia Jovičević Klug, Levi Tegg, Matic Klug Jovičević, Rahul Parmar, Matteo Amati, Luca Gregoratti, László Almásy, Julie M. Cairney, Bojan Podgornik, 2023, izvirni znanstveni članek Ključne besede: cryogenic temperature, surface chemistry, microstructure, atom probe tomography (APT), scanning photoelectron microscopy (SPEM), small angle neutron scattering (SANS) Objavljeno v DiRROS: 08.03.2024; Ogledov: 89; Prenosov: 83 Celotno besedilo (20,08 MB) Gradivo ima več datotek! Več... |
2. Austenite reversion suppression with deep cryogenic treatment : a novel pathway towards 3rd generation advanced high-strength steelsPatricia Jovičević Klug, Matic Klug Jovičević, Lars Thormählen, Jeffrey McCord, Michael Rohwerder, Matjaž Godec, Bojan Podgornik, 2023, izvirni znanstveni članek Ključne besede: Martensitic stainless steel, deep cryogenic treatment, microstructure, mechanical properties, microstructural transformations, phase transformation Objavljeno v DiRROS: 02.02.2024; Ogledov: 148; Prenosov: 79 Celotno besedilo (13,70 MB) Gradivo ima več datotek! Več... |
3. Complex interdependency of microstructure, mechanical properties, fatigue resistance, and residual stress of austenitic stainless steels AISI 304LPatricia Jovičević Klug, Matic Klug Jovičević, Michael Rohwerder, Matjaž Godec, Bojan Podgornik, 2023, izvirni znanstveni članek Ključne besede: stainless steel, AISI 304L, deep cryogenic treatment (DCT), microstructure, mechanical properties, fatigue, residual stress Objavljeno v DiRROS: 02.02.2024; Ogledov: 158; Prenosov: 76 Celotno besedilo (5,90 MB) Gradivo ima več datotek! Več... |
4. Differences between 3-D printed and traditionally milled CoCr dental alloy from casted block in oral environmentMirjam Bajt Leban, Matej Kurnik, Igor Kopač, Matic Klug Jovičević, Bojan Podgornik, Tadeja Kosec, 2023, izvirni znanstveni članek Povzetek: The aim of this study was to compare corrosion resistance and ion release in CoCr dental alloys with identical chemical compositions produced using different technologies (SLM – selective laser melting and milling from cast blocks) and heat treatment (SLM parts only). The corrosion properties were tested in artificial saliva, artificial saliva with fluoride ions, and artificial saliva with added lactic acid to simulate inflammations. The study included electrochemical tests, microstructural investigation and ion release tests in the three different environments for a total of 42 days. The best performance of CoCr as a result of potentiodynamic polarization was observed in the artificial saliva with added lactic acid, which is in contradiction with the highest ion release measured from all the materials tested and electrochemical impedance spectroscopy that showed a deterioration of the passive layer in an acidic environment. Microstructural investigation revealed that different phases precipitated by heat treatment trigger increased release of Mo and W ions. The printing method does not raise critically ion release from CoCr alloy, while the state of the surface greatly impacts the extent of the ion release. This study demonstrates the importance of an interdisciplinary approach to the study of corrosion and biocompatibility in dental alloys. Ključne besede: CoCr dental alloy, selective laser melting, corrosion, ion release, artificial saliva Objavljeno v DiRROS: 29.05.2023; Ogledov: 334; Prenosov: 280 Celotno besedilo (9,28 MB) Gradivo ima več datotek! Več... |
5. Influence of the deep cryogenic treatment on AISI 52100 and AISI D3 steelʼs corrosion resistancePatricia Jovičević Klug, Tjaša Kranjec, Matic Klug Jovičević, Tadeja Kosec, Bojan Podgornik, 2021, izvirni znanstveni članek Povzetek: The effect of deep cryogenic treatment (DCT) on corrosion resistance of steels AISI 52100 and AISI D3 is investigated and compared with conventional heat-treated counterparts. DCTʼs influence on microstructural changes is subsequently correlated to the corrosion resistance. DCT is confirmed to reduce the formation of corrosion products on steelsʼ surface, retard the corrosion products development and propagation. DCT reduces surface cracking, which is considered to be related to modified residual stress state of the material. DCTʼs influence on each steel results from the altered microstructure and alloying element concentration that depends on steel matrix and type. This study presents DCT as an effective method for corrosion resistance alteration of steels. Ključne besede: steel, deep cryogenic treatment, corrosion, Raman, open access Objavljeno v DiRROS: 19.05.2023; Ogledov: 286; Prenosov: 211 Celotno besedilo (3,13 MB) Gradivo ima več datotek! Več... |
6. |
7. Revealing the Pb whisker growth mechanism from Al-alloy surface and morphological dependency on material stress and growth environmentMatic Klug Jovičević, Tim Verbovšek, Patricia Jovičević Klug, Barbara Šetina, Bojan Ambrožič, Goran Dražić, Bojan Podgornik, 2022, izvirni znanstveni članek Ključne besede: aluminum alloy, metallic whiskers, residual stress, crystal growth, oxidation Objavljeno v DiRROS: 06.05.2022; Ogledov: 567; Prenosov: 195 Povezava na datoteko |
8. |
9. Influence of deep cryogenic treatment on natural and artificial aging of Al-Mg-Si alloy EN AW 6026Matic Klug Jovičević, Rok Rezar, Patricia Jovičević Klug, Bojan Podgornik, 2022, izvirni znanstveni članek Ključne besede: aluminum alloy, microstructure, mechanical properties, precipitation, dispersoids, deep cryogenic treatment Objavljeno v DiRROS: 06.05.2022; Ogledov: 498; Prenosov: 195 Povezava na datoteko |