Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Ključne besede: thermal analysis, hot-work tool steels, differential scanning calorimetry, heat treatment
Objavljeno v DiRROS: 08.03.2024; Ogledov: 92; Prenosov: 50
Celotno besedilo (3,08 MB)
Gradivo ima več datotek! Več...

Ključne besede: interim storage, spent fuel, borated stainless steel, cold working, bending
Objavljeno v DiRROS: 01.02.2024; Ogledov: 143; Prenosov: 66
Celotno besedilo (10,05 MB)
Gradivo ima več datotek! Več...

Povzetek: The high temperature corrosion at 650°C in the presence of NaCl at atmospheric pressure of AISI 304L, AISI 309, AISI 310S, AISI 314 and AISI 321 austenitic stainless steel was studied. The specimens were cyclically heated in the furnace and immersed in a 3.5% aqueous NaCl solution after cooling for 15 min. After each cycle, the change in mass of the samples was measured. The corroded samples were analysed by SEM /EDX, and the corrosion products were analysed by XRD. The chloride ions react with the steel surface to form porous and poorly adherent oxides and metal chlorides. After the mass increase during the first exposure cycles, spalling of the oxides occurred. The high temperature austenitic stainless steels (AISI 309, AISI 310S, AISI 314) showed less mass loss than conventional austenitic steels (AISI 304L). Surprisingly, the stainless steel AISI 321 showed a similar low weight loss after the cyclic test as AISI 309, but a detailed analysis of the exposed surfaces after the test showed a similar corrosion attack as for AISI 304. After the cyclic test at high temperature in the presence of NaCl, a higher concentration of Cr and Ni definitely improves the corrosion resistance under the present conditions, but a certain addition of Si is even more obvious.
Ključne besede: austenitic stainless steel, high temperature corrosion, NaCl, exhaust systems, open access
Objavljeno v DiRROS: 31.05.2023; Ogledov: 276; Prenosov: 175
Celotno besedilo (1,53 MB)
Gradivo ima več datotek! Več...

Povzetek: Lecanosticta acicola is a pine needle pathogen causing brown spot needle blight that results in premature needle shedding with considerable damage described in North America, Europe, and Asia. Microsatellite and mating type markers were used to study the population genetics, migration history, and reproduction mode of the pathogen, based on a collection of 650 isolates from 27 countries and 26 hosts across the range of L. acicola. The presence of L. acicola in Georgia was confirmed in this study. Migration analyses indicate there have been several introduction events from North America into Europe. However, some of the source populations still appear to remain unknown. The populations in Croatia and western Asia appear to originate from genetically similar populations in North America. Intercontinental movement of the pathogen was reflected in an identical haplotype occurring on two continents, in North America (Canada) and Europe (Germany). Several shared haplotypes between European populations further suggests more local pathogen movement between countries. Moreover, migration analyses indicate that the populations in northern Europe originate from more established populations in central Europe. Overall, the highest genetic diversity was observed in south-eastern USA. In Europe, the highest diversity was observed in France, where the presence of both known pathogen lineages was recorded. Less than half of the observed populations contained mating types in equal proportions. Although there is evidence of some sexual reproduction taking place, the pathogen spreads predominantly asexually and through anthropogenic activity.
Ključne besede: brown spot needle blight, Lecanosticta acicola, pones, Pinus spp., popularion structure
Objavljeno v DiRROS: 12.08.2022; Ogledov: 599; Prenosov: 293
Celotno besedilo (3,06 MB)
Gradivo ima več datotek! Več...

Povzetek: This report summarises the current state of knowledge in genetic aspects linked to the production and use of forest reproductive material (FRM). The first chapter describes the different categories of FRM, considers the strategic choice between artificial and natural regeneration in the face of climate change, and articulates the need for and purposes of FRM. Chapter 2 outlines the FRM production chain, in terms of: i) FRM approval, management, collection and certification (seed sources, stands, orchards, plus trees and clones others); ii) Testing standards and examples; iii) Effect of seed and seedling material not intended for use as FRM on forest genetic resources; iv) Breeding effects on basic material including conservation strategy; v) Harvesting, processing and storage of seeds; vi) Nursery practices; vii) Certification and Traceability; and viii) FRM Trading and Transport. Chapter 3 examines FRM with regard to: i) Forest regeneration strategies % especially considering climate change, and ii) Assisted migration and available decision support tools. Chapter 4 provides a detailed overview of forest establishment methods, and chapter 5 looks at keeping records of seed origin to improve forest management. The final chapter offers 38 recommendations arising from the review. This work is the result of an international collaboration rooted in EUFORGEN for more than two decades. It is built on the firm belief that the genetic element is decisive for the creation of a resilient forest capable of surviving threats and adapting to changes, thus enabling the evolution of ecosystems and the conservation of the productive landscape.
Ključne besede: forest reproductive material
Objavljeno v DiRROS: 05.11.2021; Ogledov: 846; Prenosov: 468
Celotno besedilo (5,81 MB)
Gradivo ima več datotek! Več...