11. Possibilities for improvement of mechanical properties of high-strength medium-carbon SiCr steelsPavel Salvetr, Jakub Kotous, Črtomir Donik, Aleksandr Gokhman, Zbyšek Nový, 2023, original scientific article Keywords: spring steel, 54SiCr6 steel, microstructure, mechanical properties
Published in DiRROS: 02.02.2024; Views: 250; Downloads: 83
 Full text (1,44 MB)
This document has many files! More... |
12. Austenite reversion suppression with deep cryogenic treatment : a novel pathway towards 3rd generation advanced high-strength steelsPatricia Jovičević Klug, Matic Klug Jovičević, Lars Thormählen, Jeffrey McCord, Michael Rohwerder, Matjaž Godec, Bojan Podgornik, 2023, original scientific article Keywords: Martensitic stainless steel, deep cryogenic treatment, microstructure, mechanical properties, microstructural transformations, phase transformation
Published in DiRROS: 02.02.2024; Views: 184; Downloads: 92
Full text (13,70 MB)
This document has many files! More... |
13. Hybrid additive manufacturing of Ti6Al4V with powder-bed fusion and direct-energy depositionSimon Malej, Matjaž Godec, Črtomir Donik, Matej Balažic, René Zettler, Thomas Lienert, Laurent Pambaguian, 2023, original scientific article Keywords: hybrid additive manufacturing, Ti6Al4V, tensile properties, defects, microstructure, phase transformation
Published in DiRROS: 02.02.2024; Views: 169; Downloads: 89
Full text (18,54 MB)
This document has many files! More... |
14. Effect of double-step and strain-assisted tempering on properties of medium-carbon steelPavel Salvetr, Andrea Školáková, Jakub Kotous, J. Drahokoupil, Daniel Melzer, Zdeňek Jansa, Črtomir Donik, Aleksandr Gokhman, Zbyšek Nový, 2023, original scientific article Keywords: medium-carbon steel, tempering, strengthening, mechanical properties, microstructure
Published in DiRROS: 02.02.2024; Views: 184; Downloads: 86
Full text (9,82 MB)
This document has many files! More... |
15. Dispersoids in Al-Mg-Si alloy AA 6086 modified by Sc and YFranc Zupanič, Sandi Žist, Mihaela Albu, Ilse Letofsky-Papst, Jaka Burja, Maja Vončina, Tonica Bončina, 2023, original scientific article Keywords: aluminium alloy, heat treatment, microstructure, dispersoids, dilatometry, DSC, hardness
Published in DiRROS: 02.02.2024; Views: 166; Downloads: 86
Full text (11,03 MB)
This document has many files! More... |
16. Complex interdependency of microstructure, mechanical properties, fatigue resistance, and residual stress of austenitic stainless steels AISI 304LPatricia Jovičević Klug, Matic Klug Jovičević, Michael Rohwerder, Matjaž Godec, Bojan Podgornik, 2023, original scientific article Keywords: stainless steel, AISI 304L, deep cryogenic treatment (DCT), microstructure, mechanical properties, fatigue, residual stress
Published in DiRROS: 02.02.2024; Views: 206; Downloads: 91
Full text (5,90 MB)
This document has many files! More... |
17. Solidification behavior of Fe-6.5Si alloy powder for AM-SLM processing, as assessed by differential scanning calorimetryDarja Steiner Petrovič, Črtomir Donik, Irena Paulin, Matjaž Godec, Maja Vončina, Martin Petrun, 2023, original scientific article Keywords: soft magnetic alloy, differential scanning calorimetry, oxygen, high-temperature phase, microstructure, eutectics
Published in DiRROS: 02.02.2024; Views: 169; Downloads: 77
Full text (9,05 MB)
This document has many files! More... |
18. Influence of precipitation hardening on the mechanical properties of Co-Cr-Mo and Co-Cr-W-Mo dental alloysMarko Sedlaček, Katja Zupančič, Barbara Šetina, Borut Kosec, Matija Zorc, Aleš Nagode, 2023, original scientific article Keywords: Co-Cr alloys, microstructure analysis, hardness, wear resistance
Published in DiRROS: 01.02.2024; Views: 214; Downloads: 128
Full text (53,05 MB)
This document has many files! More... |
19. Ultra-high strenght TWIP steel with high chromium contentPavel Podaný, Tomáš Studecký, Tomas Gregor, Radek Prochazka, Aleksandra Kocijan, 2023, original scientific article Abstract: A new ultra-high strength steel with a fully austenitic microstructure and twinning-induced plasticity (TWIP) effect has been developed. TWIP effect gives this steel a good combination of high strength of over 1000 MPa and ductility of over 35%. This new steel has a high chromium content, which increases its corrosion resistance. By combining cold rolling and annealing, the steel has achieved a very fine austenitic microstructure with an average grain diameter of 2.85 µm. This steel could be used for structural applications or components that need to withstand high levels of stress, deformation and corrosion environment.
Keywords: TWIP steels, corrosion resistance, microstructure, tensile strength, plasticity
Published in DiRROS: 31.01.2024; Views: 220; Downloads: 89
 Link to file
This document has many files! More... |
20. Use of steel slag for the synthesis of belite-sulfoaluminate clinkerLea Žibret, Martina Cvetković, Maruša Mrak, Mojca Loncnar, Andrej Ipavec, Sabina Dolenec, 2020, published scientific conference contribution Abstract: Belite-sulfoaluminate (BCSA) cements are low-carbon mineral binders, which require low energy consumption and allow the incorporation of various secondary raw materials in the clinker raw meal. In this study two types of unprocessed steel slags, coming from stainless steel production, were incorporated in the BCSA clinkers. The clinker phase composition, clinker reactivity, and the compressive strength of the cement were studied to evaluate the possible use of the slag in BCSA clinkers. The cement clinkers were synthesized by using natural raw materials, white titanogypsum, mill scale, as well as two different steel slags: (i) EAF S slag, which is a by-product of melting the recycled steel scrap in an electric arc furnace, and (ii) la dle slag as a by-product of the processes of secondary metallurgy, in various quantities. Raw mixtures with two different targeted phase compositions varying in belite, calcium sulfoaluminate and ferrite phases were sintered at 1250 °C. Clinker phases were determined by Rietveld quantitative phase analysis, while their distribution, morphology and incorporation of foreign ions in the phases were studied by SEM/EDS analysis. The clinker reactivity was determined by isothermal calorimetry. BCSA cements were prepared by adding titanogypsum. The compressive strength of the cement pastes was determined after 7 days of hydration. The presence of a predicted major clinker phases was confirmed by Rietveld analysis, however periclase was also detected. Microscopy revealed subhedral grains of belite and euhedral grains of calcium sulfoaluminate phases, while ferrite occurred as an interstitial phase. The results showed differences in the microstructure and reactivity of the clinker and cement, which can be attributed to varying amounts of ettringite due to different slag types
Keywords: belite-sulfoaluminate cement, cement clinker, steel slags, clinker microstructure, cement reactivity
Published in DiRROS: 19.01.2024; Views: 208; Downloads: 84
Full text (18,89 MB)
This document has many files! More... |
