41. |
42. RILEM TC 247-DTA round robin test : mix design and reproducibility of compressive strength of alkaliactivated concretesJohn L. Provis, Kamel Arbi, Susana Bernal, Dali Bondar, Anja Buchwald, Arnaud Castel, Sundararaman Chithiraputhiran, Martin Cyr, Alireza Dehghan, Katja Dombrowski-Daube, Ashish Dubey, Vilma Ducman, Gregor J. G. Gluth, Sreejith Nanukuttan, Karl Peterson, Francisca Puertas, Arie van Riessen, Manuel Torres-Carrasco, Guang Ye, Yibing Zuo, 2019, original scientific article Abstract: The aim of RILEM TC 247-DTA Durability Testing of Alkali-Activated Materials is to identify and validate methodologies for testing the durability of alkali-activated concretes. To underpin the durability testing work of this committee, five alkali-activated concrete mixes were developed based on blast furnace slag, fly ash, and flash-calcined metakaolin. The concretes were designed with different intended performance levels, aiming to assess the capability of test methods to discriminate between concretes on this basis. A total of fifteen laboratories worldwide participated in this round robin test programme, where all concretes were produced with the same mix designs, from single-source aluminosilicate precursors and locally available aggregates. This paper reports the mix designs tested, and the compressive strength results obtained, including critical insight into reasons for the observed variability in strength within and between laboratories.
Keywords: alkali-activated materials (AAM), mechanical properties, test method, Rilem TC, durability
Published in DiRROS: 14.09.2023; Views: 261; Downloads: 150
 Full text (431,19 KB)
This document has many files! More... |
43. |
44. |
45. Periodic anti-phase boundaries and crystal superstructures in ▫$PtCu_3$▫ nanoparticles as fuel cell electrocatalystsAna Rebeka Kamšek, Anton Meden, Iztok Arčon, Primož Jovanovič, Martin Šala, Francisco Ruiz-Zepeda, Goran Dražić, Miran Gaberšček, Marjan Bele, Nejc Hodnik, 2023, original scientific article Published in DiRROS: 28.08.2023; Views: 442; Downloads: 218
Full text (2,13 MB)
This document has many files! More... |
46. Stress corrosion crack initiation testing with tapered specimens in high-temperature water - results of a collaborative research projectRik-Wouter Bosch, Stefan Ritter, Matthias Herbst, Renate Kilian, Grace Burke, Jonathan Duff, Fabio Scenini, Yuchen Gu, Alice Dinu, Ulla Ehrnsten, Aki Toivonen, Radek Novotny, Oliver Martin, Francisco Javier Perosanz, Andraž Legat, Bojan Zajec, 2020, original scientific article Abstract: The applicability of an accelerated test technique using tapered tensile specimens for investigating the stress corrosion crack (SCC) initiation behaviour of structural materials in high-temperature water was assessed in the framework of a European collaborative research project (MICRIN – MItigation of CRack INitiation). The main advantage of using a tapered geometry is, that in a single test a stress gradient is obtained through the gauge length, and therefore a stress threshold for SCC initiation can be determined in a reasonable timeframe. This method was used to investigate two different materials that were known to be susceptible to SCC in light water reactor environment: a high-Si stainless steel and a Ni-base weld metal (Alloy 182). The results of the international test programme confirmed that the tapered specimen test methodology could be used to identify a SCC initiation stress threshold, albeit that significant scatter was present in the data.
Keywords: stress corrosion cracking, surface finish impact, tapered tensile specimen, autoclave, accelerated testing, light water nuclear reactor, critical threshold stress
Published in DiRROS: 28.08.2023; Views: 318; Downloads: 168
Full text (3,05 MB)
This document has many files! More... |
47. |
48. |
49. |
50. |
