Digital repository of Slovenian research organisations

Search the repository
A+ | A- | Help | SLO | ENG

Query: search in
search in
search in
search in

Options:
  Reset


Query: "author" (Aleksandra Kocijan) .

1 - 10 / 15
First pagePrevious page12Next pageLast page
1.
2.
3.
4.
5.
6.
Development of the recycling procedure for rapid antigen tests
Rebeka Rudolf, Darja Feizpour, Žiga Jelen, Peter Majerič, Tilen Švarc, Matej Zadravec, Timi Gomboc, Aleksandra Kocijan, 2024, original scientific article

Keywords: rapid antigen tests, recycling, characterization, nanogold, plastic
Published in DiRROS: 28.02.2024; Views: 109; Downloads: 42
.pdf Full text (1,74 MB)
This document has many files! More...

7.
Material properties of high-strength high chromium TWIP steel with increased corrosion resistance
Pavel Podaný, Tomáš Studecký, Aleksandra Kocijan, 2023, original scientific article

Keywords: TWIP, steels, microstructure, mechanical properties, corrosion
Published in DiRROS: 02.02.2024; Views: 163; Downloads: 70
.pdf Full text (448,19 KB)
This document has many files! More...

8.
Tribological evaluation of vegetable ▫$oil/MoS_2$▫ nanotube-based lubrication of laser-textured stainless steel
Marjetka Conradi, Bojan Podgornik, Maja Remškar, Damjan Klobčar, Aleksandra Kocijan, 2023, original scientific article

Abstract: In the present work, the functionalisation of austenitic stainless steel, AISI 316L surfaces via nanosecond Nd:YAG laser texturing in order to modify the surface morphology with crosshatch and dimple patterns is presented. A tribological analysis under lubrication with sunflower and jojoba oil with and without the addition of a solid lubricant, MoS2 nanotubes, was performed. In conjunction with friction/wear response laser-textured surface wettability, oil spreadability and oil retention capacity were also analysed. It was shown that the crosshatch pattern generally exhibited lower friction than the dimple pattern, with the addition of MoS2 nanotubes not having any significant effect on the coefficient of friction under the investigated contact conditions. This was found in addition to the better oil spreadability and oil retention capacity results of the crosshatch-textured surface. Furthermore, texturing reduced the wear of the stainless-steel surfaces but led to an approximately one order of magnitude larger wear rate of the steel counter-body, primarily due to the presence of hard bulges around the textured patterns. Overall, the crosshatch pattern showed better oil retention capacity and lower friction in combination with different vegetable oils, thus making it a promising choice for improving tribological performance in various environmentally friendly applications.
Keywords: tribology, stainless steel, vegetable oil lubrication, MoS2 nanotubes
Published in DiRROS: 02.02.2024; Views: 101; Downloads: 56
.pdf Full text (4,56 MB)
This document has many files! More...

9.
Influence of oil viscosity on the tribological behavior of a laser-textured Ti6Al4V alloy
Marjetka Conradi, Aleksandra Kocijan, Bojan Podgornik, 2023, original scientific article

Abstract: Laser texturing with a dimple pattern was applied to modify a Ti6Al4V alloy at the micro level, aiming to improve its friction and wear resistance in combination with oil lubrication to optimize the performance in demanding industrial environments. The tribological analysis was performed on four different dimple-textured surfaces with varying dimple size and dimple-to-dimple distance and under lubrication with three different oils, i.e., T9, VG46, and VG100, to reflect the oil viscosity’s influence on the friction/wear of the laser-textured Ti6Al4V alloy. The results show that the surfaces with the highest texture density showed the most significant COF reduction of around 10% in a low-viscosity oil (T9). However, in high-viscosity oils (VG46 and VG100), the influence of the laser texturing on the COF was less pronounced. A wear analysis revealed that the laser texturing intensified the abrasive wear, especially on surfaces with a higher texture density. For low-texturing-density surfaces, less wear was observed for low- and medium-viscosity oils (T9 and VG46). For medium-to-high-texturing densities, the high-viscosity oil (VG100) provided the best contact conditions and wear results. Overall, reduced wear, even below the non-texturing case, was observed for sample 50–200 in VG100 lubrication, indicating the combined effect of oil reservoirs and increased oil-film thickness within the dimples due to the high viscosity.
Keywords: oil lubrication, surface modification, Ti-based alloy, tribology
Published in DiRROS: 01.02.2024; Views: 131; Downloads: 45
.pdf Full text (4,00 MB)
This document has many files! More...

10.
Ultra-high strenght TWIP steel with high chromium content
Pavel Podaný, Tomáš Studecký, Tomas Gregor, Radek Prochazka, Aleksandra Kocijan, 2023, original scientific article

Abstract: A new ultra-high strength steel with a fully austenitic microstructure and twinning-induced plasticity (TWIP) effect has been developed. TWIP effect gives this steel a good combination of high strength of over 1000 MPa and ductility of over 35%. This new steel has a high chromium content, which increases its corrosion resistance. By combining cold rolling and annealing, the steel has achieved a very fine austenitic microstructure with an average grain diameter of 2.85 µm. This steel could be used for structural applications or components that need to withstand high levels of stress, deformation and corrosion environment.
Keywords: TWIP steels, corrosion resistance, microstructure, tensile strength, plasticity
Published in DiRROS: 31.01.2024; Views: 147; Downloads: 53
.pdf Full text (1,44 MB)
This document has many files! More...

Search done in 0.34 sec.
Back to top