1. Flexible polymer connections for clt structuresBoris Azinović, Andreja Pondelak, Jaka Gašper Pečnik, Václav Sebera, 2020, objavljeni znanstveni prispevek na konferenci Povzetek: This paper explores the possibility of using flexible polymer adhesives to dissipate energy in CLT buildings during earthquakes. In the first series of tests, pull-off tests of various polyurethane (PUR) adhesives were performed. The connection was tested in pull-pull configuration using monotonic, tension-only loading. The tests have shown that the adhesive can resist large deformations already in tension loading and with small thicknesses of the bond-line. Based on the pull-off test results, one adhesive has been selected for further testing. Monotonic lap-shear tests were performed with the selected adhesive and thick bond-line (3 mm and 6 mm). The results show, that the standard method for lap-shear testing (EN 205) needs to be adapted for thick glue-line. It was found that the strength of 3 mm glue-line is higher than 6mm one, which is in agreement with adhesion theory. The flexible PUR adhesives could potentially be used in CLT structures for anchoring the CLT wall with “flexible” glued-in rods or as a “flexible” vertical shear connection between the CLT walls. Such systems have a potential to dissipate energy in seismic areas. Ključne besede: CLT connections, flexible adhesive, polyurethane, energy dissipation, pull-off, lap-shear Objavljeno v DiRROS: 19.01.2024; Ogledov: 344; Prenosov: 172 Celotno besedilo (18,89 MB) Gradivo ima več datotek! Več... |
2. Experimental investigation of the axial strength of glued-in rods in cross laminated timberBoris Azinović, Erik Serrano, Miha Kramar, Tomaž Pazlar, 2018, izvirni znanstveni članek Povzetek: This paper presents results from an experimental assessment of glued-in rods in cross laminated timber (CLT). For the purposes of the study more than 60 pull-pull tests were performed, where the specimens varied in terms of bonded-in length (from 80 to 400 mm), rod diameter (16-24 mm) and rod-to-grain angle (parallel and perpendicular). Several different failure modes that are not common for other applications of glued-in rods (e.g., a failure between CLT layers) were obtained for the analysed CLT specimens. It was found that these failure mechanisms can substantially influence the obtained ultimate tension loads. At the end, the experimental results were compared with empirical and semi-empirical equations for estimating the pull-out strength of glued-in rods in structural timber and glulam. The comparison showed that most of the existing equations overestimate the ultimate tension loads for specimens with the rod parallel to the grain and underestimate the ultimate tension load for specimens with the rod perpendicular to the grain. The results vary because the possible CLT failure modes were not included in previous studies. Further studies are proposed to improve the equations for glued-in rods in CLT. Ključne besede: glued-in rods, cross laminated timber (CLT), pull-pull experiment, glued-in length, rod-to-grain angle, failure mechanisms in CLT Objavljeno v DiRROS: 29.11.2023; Ogledov: 363; Prenosov: 283 Celotno besedilo (4,13 MB) Gradivo ima več datotek! Več... |
3. Characterizing the interfacial zones of fly ash based alkali activated adhesives to various substratesWolfgang Wisniewski, Vilma Ducman, 2022, izvirni znanstveni članek Povzetek: Alkali Activated Materials (AAMs) are important potential substitutes for cement in many materials. The AAMs presented here are based on industrial ground granulated blast furnace slag (GGBFS) and fly ash (FA). They are tested for their suitability as adhesives for joining concrete, ceramic tiles, a wood-based geopolymer (WGP) and a high density geopolymer (HDGP). After mixing multiple batches and performing preliminary tests of the resulting shrinkage, bending-, compressive- and pull-of-strengths to standard ceramic tiles, selected mixtures are tested for their open time and applied to bond intended substrates. The interfacial zones (ITZ) of an AAM containing additional KOH and the most comparable KOH-free AAM to concrete, ceramic tiles, WPG and HDGP are subsequently characterized in detail using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDXS). Both mechanical interlocking and areas of probable chemical bonding are identified. Ključne besede: adhisive, fly ash, ITZ, pull of test, open ccess Objavljeno v DiRROS: 21.06.2023; Ogledov: 471; Prenosov: 303 Celotno besedilo (4,51 MB) Gradivo ima več datotek! Več... |