Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Ključne besede: hot work tool steel, microalloying, močybdenum, tungsten, tempering, heat treatment
Objavljeno v DiRROS: 20.05.2024; Ogledov: 69; Prenosov: 37
Povezava na datoteko

Ključne besede: thermal analysis, hot-work tool steels, differential scanning calorimetry, heat treatment
Objavljeno v DiRROS: 08.03.2024; Ogledov: 131; Prenosov: 63
Celotno besedilo (3,08 MB)
Gradivo ima več datotek! Več...

Povzetek: Hot-work tool steels are extensively used in industrial applications that require high resistance to mechanical and chemical degradation at elevated temperatures. To meet these requirements, hot-work tool steels must exhibit good mechanical properties, including high tensile strength, hardness, wear resistance, and tempering resistance, as well as high thermal conductivity and ductility. This study investigates the ductility of the hot-work tool steel HTCS-130, which suffers from low ductility due to the presence of stable molybdenum-tungsten carbides (M6C) on the prior austenite crystal grain boundaries. Increasing austenitisation temperatures or prolonging the dwelling time at temperature can promote intensive migration of grain boundaries, leading to negative effects on the mechanical properties of the steel. To address this issue, isothermal transformation in the bainitic area between 350 and 500 °C was performed. Isothermal transformation at around 350 °C leads to the formation of lower bainite, which has similar hardness to tempered martensite. As the temperature of isothermal transformation increases, the hardness of the material decreases, due to the formation of upper bainite. The hardness analysis was measured using the Vickers method, the impact toughness of the steel samples was measured using a Charpy test with V-notched samples. The microstructure characterization was performed using optical and scanning electron microscopy. The improvement of ductility can be achieved by controlling the isothermal transformation of bainite and adjusting the heat treatment conHot-work tool steels are extensively used in industrial applications that require high resistance to mechanical and chemical degradation at elevated temperatures. To meet these requirements, hot-work tool steels must exhibit good mechanical properties, including high tensile strength, hardness, wear resistance, and tempering resistance, as well as high thermal conductivity and ductility. This study investigates the ductility of the hot-work tool steel HTCS-130, which suffers from low ductility due to the presence of stable molybdenum-tungsten carbides (M6C) on the prior austenite crystal grain boundaries. Increasing austenitisation temperatures or prolonging the dwelling time at temperature can promote intensive migration of grain boundaries, leading to negative effects on the mechanical properties of the steel. To address this issue, isothermal transformation in the bainitic area between 350 and 500 °C was performed. Isothermal transformation at around 350 °C leads to the formation of lower bainite, which has similar hardness to tempered martensite. As the temperature of isothermal transformation increases, the hardness of the material decreases, due to the formation of upper bainite. The hardness analysis was measured using the Vickers method, the impact toughness of the steel samples was measured using a Charpy test with V-notched samples. The microstructure characterization was performed using optical and scanning electron microscopy. The improvement of ductility can be achieved by controlling the isothermal transformation of bainite and adjusting the heat treatment conditions. These findings provide useful insights into the design and optimization of heat treatment processes for hot-work tool steels.ditions. These findings provide useful insights into the design and optimization of heat treatment processes for hot-work tool steels.
Ključne besede: hot-work tool steel, austempering, bainitic transformation, ductility, dilatometry
Objavljeno v DiRROS: 28.02.2024; Ogledov: 206; Prenosov: 83
Celotno besedilo (1,02 MB)
Gradivo ima več datotek! Več...

Ključne besede: aluminum alloy, hot rolling, simulations, metallography, mechanical properties
Objavljeno v DiRROS: 01.02.2024; Ogledov: 199; Prenosov: 102
Celotno besedilo (5,46 MB)
Gradivo ima več datotek! Več...

Ključne besede: ionisation vacuum gauge, hot cathode, sensitivity, secondary electrons, ion induced secondary electron yield
Objavljeno v DiRROS: 26.01.2024; Ogledov: 288; Prenosov: 108
Celotno besedilo (3,39 MB)
Gradivo ima več datotek! Več...