Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Povzetek: An efficient approach for tailoring surface properties of polymers is presented, which enables rapid modification leading to superhydrophilic properties. The approach is based on vacuum-ultraviolet radiation (VUV) pretreatment of the surface to create reactive dangling bonds. This step is followed by a second treatment using neutral oxygen atoms that react with the dangling bonds and form functional groups. The beneficial effect of VUV pretreatment for enhanced functionalization was clearly demonstrated by comparing VUV pretreatment in plasmas created in different gases, i.e., hydrogen, nitrogen, and oxygen, which differ in the intensity of VUV/UV radiation. The emission intensity of VUV radiation for all gases was measured by vacuum ultraviolet spectroscopy. It was shown that VUV has a strong influence on the treatment time and final surface wettability. A superhydrophilic surface was obtained only if using VUV pretreatment. Furthermore, the treatment time was significantly reduced to only a second of treatment. These findings show that such an approach may be used to enhance the surface reaction efficiency for further grafting of chemical groups.
Ključne besede: plasma treatment, vacuum-ultraviolet radiation treatment, surface functionalization, polymer polyvinyl chloride, vacuum-ultraviolet spectroscopy, vacuum-ultraviolet photons
Objavljeno v DiRROS: 06.06.2023; Ogledov: 509; Prenosov: 229
Celotno besedilo (4,42 MB)
Gradivo ima več datotek! Več...

Povzetek: The ever-growing worldwide demand for fired clay brick has resulted in the shortage of clay in many parts of the world. Therefore, there is a need to look for more sustainable alternative materials for the brick manufacturing. This study has investigated the potential use of the untreated Drava River sediment as a substitute material for clay in the production of fired bricks, with the research being conducted at both laboratory and industrial level. At the laboratory level, brick specimens were prepared by mixing clay with different river sediment proportions (ranging from 10 to 50 wt%) and were fired at 950 °C, with microstructural and various physical–mechanical properties being analyzed. Elevated carbonate content in Drava river sediment results in higher weight loss during firing at temperatures up to 950 °C, comparing to firing pure brick-making clay. Consequently, the addition of sediment increases porosity of fired bricks, which results in lowering of their mechanical properties. Results reveal that the compressive strength of the pure clay sample was 79.5 MPa, while the compressive strength of the sample with the addition of river sediment from 10 wt% to 50 wt% decreased from 73.9 MPa to 26.2 MPa, respectively. Despite the lower compressive strength, the 26.2 MPa is still above the limit value of 10 MPa specified in the standard EN 772–1 [1]. At the industrial level, hollow clay bricks were prepared with 20 wt% of the river sediment and fired in a tunnel kiln. Inclusion of the river sediment also decreased compressive strength from 38 MPa for pure mixture to 26 MPa for 20 wt% of the sediment addition, confirming usability of Drava sediment in brick production. In addition, LCA study has been conducted to evaluate the environmental impacts associated with the industrial production of classic bricks and bricks with the addition of the river sediment. The obtained results have shown that the bricks made with the addition of the Drava River sediment are sustainable and environmentally friendly and meet all the requirements specified in the relevant regulatory standard.
Ključne besede: sediments, clay masonry units, LCA, properties
Objavljeno v DiRROS: 30.05.2023; Ogledov: 378; Prenosov: 266
Celotno besedilo (4,76 MB)
Gradivo ima več datotek! Več...

Povzetek: Materials for biomedical applications often need to be coated to enhance their performance, such as their biocompatibility, antibacterial, antioxidant, and anti-inflammatory properties, or to assist the regeneration process and influence cell adhesion. Among naturally available substances, chitosan meets the above criteria. Most synthetic polymer materials do not enable the immobilization of the chitosan film. Therefore, their surface should be altered to ensure the interaction between the surface functional groups and the amino or hydroxyl groups in the chitosan chain. Plasma treatment can provide an effective solution to this problem. This work aims to review plasma methods for surface modification of polymers for improved chitosan immobilization. The obtained surface finish is explained in view of the different mechanisms involved in treating polymers with reactive plasma species. The reviewed literature showed that researchers usually use two different approaches: direct immobilization of chitosan on the plasma-treated surface or indirect immobilization by additional chemistry and coupling agents, which are also reviewed. Although plasma treatment leads to remarkably improved surface wettability, this was not the case for chitosan-coated samples, where a wide range of wettability was reported ranging from almost superhydrophilic to hydrophobic, which may have a negative effect on the formation of chitosan-based hydrogels.
Ključne besede: polymer surfaces, chitosan, coatings, plasma-surface modification, adhesion
Objavljeno v DiRROS: 24.02.2023; Ogledov: 501; Prenosov: 252
Celotno besedilo (6,88 MB)
Gradivo ima več datotek! Več...

Ključne besede: onkologija, rak dojke, obsevanje
Objavljeno v DiRROS: 09.02.2023; Ogledov: 388; Prenosov: 121
Celotno besedilo (40,23 KB)

Objavljeno v DiRROS: 13.01.2023; Ogledov: 689; Prenosov: 155
Celotno besedilo (1,62 MB)