Search the repository

A+ | A- | | SLO | ENG

Abstract: Cost-effectiveness is a key consideration within fire safety engineering. Currently, different approaches are being applied in literature. These approaches differ in how cost-effectiveness is evaluated, which costs are considered, and how the preferred design solution is defined. Recognizing this issue, the Fire Protection Research Foundation enrolled an international team of researchers, supported by a broad stakeholder panel, to develop a reference methodology. In this paper, this reference methodology for cost-benefit analysis in fire safety engineering is presented following an extensive literature review. The methodology clarifies the minimum requirements for assessing cost-effectiveness, and highlights that only a present net value evaluation can be used to compare design alternatives. Commonly used cost-benefit ratios should only be used when deciding on the effectiveness of a single package of fire safety measures. An illustrative case study demonstrates the application of the meth- odology and shows how designs based on cost-benefit ratios can be sub-optimal when evaluating multiple possible fire safety measures.
Keywords: cost-benefit analysis, fire safety, investment, maintenance, loss, statistics, reliability
Published in DiRROS: 23.10.2023; Views: 432; Downloads: 103
Link to file
This document has many files! More...

Abstract: We present a novel % cutoff concept of colorimetric indication of relative humidity based on dye dissolution in condensed water in capillaries of selectively functionalized mesoporours host SiO2 material. Consistently high levels of indoor air humidity induces mold and algae growth which represent a potential risks for human health and have deteriorating effect on walls as well. Simple localized humidity detection of high humidity with naked eye especially at places with low air circulation, where growth of mold usually starts first, is therefore highly desirable. The reporting dye was integrated in the non-functionalized mesoporous silica matrix with different pore diameters and selective-functionalized mesoporous silica material. After exposure to the environment of different air humidities the dye dissolved in water causing color change of adsorbent. With the use of adsorbents with different mesopore diameters high ability to tune the value of relative humidity when complete capillary condensation occurred was achieved. Materials with pore diameters of 3.0%nm, 3.5%nm and 7.0%nm exhibit gradual color change when reaching relative humidity up to 55, 79 and 88 RH% respectively. After selective methylation of the material with 7.0%nm pore diameter, non-gradual cutoff color change was achieved. Sample exhibited color change at narrow range of relative humidity (cutoff color change). Due to selective functionalized outer surface the dye dissolution occur only in condensed water in pores and therefore provide colorimetric indication only in this range. Selectively modified silica material has a great potential for a straightforward detection of high humid environment.
Keywords: turn-on colorimetric probe, selective functionalization, mesoporous silica, relative humidity, capillary condensation
Published in DiRROS: 05.09.2023; Views: 394; Downloads: 275
Full text (7,18 MB)
This document has many files! More...

Abstract: Full and partial restorations in dentistry must replicate the characteristics of the patient’s natural teeth. Materials must have good mechanical properties and be non-toxic and biocompatible. Microbes, which can form biofilms, are constantly in contact with restorations. In this study, we investigate how well Candida albicans adheres to a polymethyl methacrylate (PMMA) resin base with gold (Au) nanoparticles. We synthesized Au nanoparticles and characterized them. The average size of Au nanoparticles embedded in PMMA was 11 nm. The color difference ∆E between PMMA and PMMA/Au composites was 2.7 and was still esthetically acceptable to patients. PMMA/Au surfaces are rougher and more hydrophilic than pure PMMA surfaces, and the isoelectric point of both types of surfaces was 4.3. Above the isoelectric point, PMMA/Au surfaces are more negatively charged than PMMA surfaces. The added Au nanoparticles decreased the tensile strength, while the hardness did not change significantly. Adhesion measurements showed that PMMA surfaces modified with Au nanoparticles reduced the extent of microbial adhesion of Candida albicans.
Keywords: fungal adhesión, C. albicans, polymethyl methacrylate resin, Au, surface properties, composites
Published in DiRROS: 24.07.2023; Views: 451; Downloads: 165
Full text (2,90 MB)
This document has many files! More...

Abstract: The demand for construction timber is continuously increasing, due to its favourable characteristics. However, the adequate protection of wood is key to its successful use, as it is flammable and susceptible to biodegradation. Given that thermal modification enhances the durability of wood, and mineralisation with CaCO3 considerably improves its fire properties, it is worth considering the combined effects of the two methods. European beech (Fagus sylvatica) was selected to determine the effects of a) thermal modification, b) mineralisation through the in-situ formation of CaCO3, and c) a combination of the two procedures, on resistance to decay fungi, reaction to fire and the mechanical properties of the wood. Microscopic analysis and comparisons of the samples before and after exposure to fungi were also conducted. Mineralised wood generally had a slightly alkaline pH value and higher equilibrium moisture content, while thermal modification lowered the equilibrium moisture content. The present study demonstrated the combined effect of thermal modification and mineralisation: the best response to fire as well as resistance to fungi was achieved when the two treatments were combined. Results from the Brinell hardness and three-point bending tests indicate that both modification procedures can slightly impair the mechanical properties of the wood.
Keywords: wood, protection, durability, mechanical properties
Published in DiRROS: 12.07.2023; Views: 390; Downloads: 279
Full text (3,26 MB)
This document has many files! More...

Abstract: Cellulose acetate is used in many applications, including for cigarette filters. Unfortunately, unlike cellulose, its (bio)degradability is under question, yet it often ends up uncontrolled in the natural environment. The main purpose of this study is to compare the effects of weathering on two types of cigarette filter (classic filters and newer filters that have more recently arrived on the market) following their use and disposal in nature. Microplastics were prepared from polymer parts of used (classic and heated tobacco products—HTP) cigarettes and artificially aged. TG/DTA, FTIR, and SEM analyses were performed both before and after the aging process. Newer tobacco products contain an additional film made of a poly(lactic acid) polymer which, like cellulose acetate, burdens the environment and poses a risk to the ecosystem. Numerous studies have been conducted on the disposal and recycling of cigarette butts and cigarette butt extracts, revealing alarming data that have also influenced the decisions of the EU, who addressed the disposal of tobacco products in the EU Directive (EU) 2019/904. Despite this, there is still no systematic analysis in the literature evaluating the impact of weathering (i.e., accelerated aging) on the degradation of cellulose acetate in classic cigarettes compared with that in newer tobacco products that have recently appeared on the market. This is of particular interest given that the latter have been promoted as being healthier and environmentally friendly. The results show that in cellulose acetate cigarette filters the particle size decreased after accelerated aging. Also, the thermal analysis revealed differences in the behavior of the aged samples, while the FTIR spectra showed no shifts in the position of the peaks. Organic substances break down under UV light, which can be seen by measuring the color change. The PLA film was found to be more stable than cellulose acetate under the influence of UV light.
Keywords: cellulose acetate, cigarette filters, microplastics, artificial weathering, polymer degradation
Published in DiRROS: 30.06.2023; Views: 441; Downloads: 247
Full text (5,78 MB)
This document has many files! More...