Digital repository of Slovenian research organisations

Search the repository
A+ | A- | Help | SLO | ENG

Query: search in
search in
search in
search in

Options:
  Reset


Query: "keywords" (visual analysis) .

1 - 3 / 3
First pagePrevious page1Next pageLast page
1.
Electrochemical corrosion tests on steel in alkali-activated materials
Nina Gartner, Miha Hren, Tadeja Kosec, Andraž Legat, 2021, published scientific conference contribution

Abstract: One of the potential alternatives to Ordinary Portland Cement (OPC) are Alkali-Activated Materials (AAMs). The service life of reinforced concrete structures greatly depends on the corrosion resistance of embedded steel reinforcement. Due to the wide range of AAMs and their diverse properties, corrosion processes of steel in these materials are relatively unknown. Corrosion monitoring methods or their interpretations in certain cases cannot be directly transferred from the ones for OPC materials. The chemical compositions of pore solution in different AAMs influence the results of electrochemical measurements and their interpretations. Within this research, three different alkali-activated mortar mixes were prepared, based on fly ash, slag or metakaolin. Pore solutions were extracted from each mortar andchemical analysis was acquired. Different electrochemical corrosion measurements were performed on steel submerged to synthetic pore solutions. In parallel, ordinary carbon steel reinforcing bar was installed in the same types of alkali-activated mortar mixes. Specimens were exposed to wet/dry cycles with saline solution and periodic measurements of electrochemical impedance spectroscopy (EIS) were performed. Measured parameters in both systems were analysedand compared. It was concluded that electrochemical measurements in pore solutions can provide basic overview on corrosion behaviour in different AAMs environments. Periodic EIS measurements enabled monitoring of corrosion initiation and propagation on steel reinforcement in AAMs, although the information on the corrosion type is missing. Interpretation of results depends on visual analysis of corrosion damages after the end of exposure, providing information on corrosion type and intensity. The continuation of research on corrosion monitoring techniques will be performed by using Electrical Resistance (ER) sensors and Coupled Multi-Electrode Array (CMEA) sensors.
Keywords: corrosion, alkali-activated mortars, pore solution extraction, electrochemical corrosion techniques, visual analysis
Published in DiRROS: 22.01.2024; Views: 163; Downloads: 92
.pdf Full text (9,29 MB)
This document has many files! More...

2.
Characterizing steel corrosion in different alkali-activated mortars
Nina Gartner, Miha Hren, Tadeja Kosec, Andraž Legat, 2021, original scientific article

Abstract: Alkali-activated materials (AAMs) present a promising potential alternative to ordinary Portland cement (OPC). The service life of reinforced concrete structures depends greatly on the corrosion resistance of the steel used for reinforcement. Due to the wide range and diverse properties of AAMs, the corrosion processes of steel in these materials is still relatively unknown. Three different alkali-activated mortar mixes, based on fly ash, slag, or metakaolin, were prepared for this research. An ordinary carbon-steel reinforcing bar was installed in each of the mortar mixes. In order to study the corrosion properties of steel in the selected mortars, the specimens were exposed to a saline solution in wet/dry cycles for 17 weeks, and periodic electrochemical impedance spectroscopy (EIS) measurements were performed. The propagation of corrosion damage on the embedded steel bars was followed using X-ray computed microtomography (XCT). Periodic EIS measurements of the AAMs showed different impedance response in individual AAMs. Moreover, these impedance responses also changed over the time of exposure. Interpretation of the results was based on visual and numerical analysis of the corrosion damages obtained by XCT, which confirmed corrosion damage of varying type and extent on steel bars embedded in the tested AAMs.
Keywords: corrosion, alkali-activated mortars, steel reinforcement, electrochemical impedance spectroscopy, X-ray computed microtomography, visual analysis
Published in DiRROS: 05.07.2023; Views: 333; Downloads: 157
.pdf Full text (7,00 MB)
This document has many files! More...

3.
Assessment of the condition of Balsam poplar trees (Populus balsamifera L.) in a residental area of Bratsk
Elena Runova, Vasilij Verkhoturov, Lyudmila Anoshkina, Ivan Garus, 2021, original scientific article

Abstract: In this study, we investigated the health status of balsam poplar (Populus balsamifera L.) trees in a residential area of the city of Bratsk (Irkutsk Oblast, Russia). Visual and instrumental assessment of the health status of pruned and unpruned trees was performed. The identified internal defects in the tree were analyzed with a Resistograph device, which enabled the extent of decayed wood to be determined. Visual analysis revealed various types of damage: dried branches, brittle crowns, frost cracks, mechanical damage, curvature of trunks, decay and inclusions of foreign bodies. We compared trees with and without canopy pruning. We found that pruned trees were significantly more damaged than non-pruned trees. Decomposing wood at different stages of development was found in all the trees studied. A tree passport combining the visual and instrumental assessment data was compiled for each tree. The results of the research were used to formulate conclusions and recommendations for improving the management of urban trees in order to restore their ecological and aesthetic functions.
Keywords: Populus balsamifera L., visual analysis, Resistograph, urban area, wood, decay
Published in DiRROS: 01.12.2021; Views: 3006; Downloads: 1820
.pdf Full text (1,84 MB)
This document has many files! More...

Search done in 0.15 sec.
Back to top