Digitalni repozitorij raziskovalnih organizacij Slovenije

Iskanje po repozitoriju
A+ | A- | Pomoč | SLO | ENG

Iskalni niz: išči po
išči po
išči po
išči po

Možnosti:
  Ponastavi


Iskalni niz: "ključne besede" (microwaves) .

1 - 3 / 3
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Influence of curing / drying methods including microwave heating on alkali activation of waste casting cores
Barbara Horvat, Vilma Ducman, 2021, objavljeni znanstveni prispevek na konferenci

Povzetek: Within previous investigation alkali activation of waste casting cores at room temperature did not give promising results, i.e. when the precursor was gently ground and sieved below 600 %m the alkali activated material fell apart at demolding, and when the precursor was ground below 90 %m, the alkali activated material did not solidify in more than 2 years. , Therefore different drying/curing methods were applied to enhance the reaction. Waste casting cores were prepared in two granulations (sieved below 600 %m and below 90 %m), activated with Na -water glass and 10 M NaOH, cured at different temperatures (70 °C and room temperature), and subsequently cured/dried at three different conditions: room temperature, 110 °C, and irradiated with microwaves. The highest compressive strength, 25 MPa, was gained with subsequent curing/drying at 110 °C. The lowest density, 0.5 kg/l, with compressive strength above 3 MPa, was achieved with subsequent curing/drying with microwaves .
Ključne besede: waste casting cores, alkali activation, curing, drying, microwaves, mechanical strength
Objavljeno v DiRROS: 22.01.2024; Ogledov: 168; Prenosov: 88
.pdf Celotno besedilo (9,29 MB)
Gradivo ima več datotek! Več...

2.
Effect of temperature on the eradication of house longhorn beetle larvae in wood by microwave treatment
Martin Klinc, Franc Pohleven, 2017, izvirni znanstveni članek

Povzetek: In repressive protection of cultural/historical woodwork, microwaves have many advantages over conventional heating. The research%s objective was to examine conditions for eradication of house longhorn beetle larvae (Hylotrupes bajulus) in spruce wood (Picea abies) using microwaves. Larvae, inserted at different depths of spruce blocks containing 12% and 42% of moisture, were exposed to microwaves. Two apparatuses were used; a 750W commercial microwave chamber and a newly developed horn antenna microwave device with the power of 800W and a frequency of 2.45GHz, for targeted radiation. We discovered that the inner part of wood warmed up quicker than the surface heated to 65°C. For successful suppression larvae in the wood need to be heated to 54.5°C, for 10 seconds. The necessary exposure time increases with increasing thickness of wood. The surface of wood containing more moisture is heated quicker, but increased moisture slows down the penetration of microwaves into the wood specimen. Therefore, larvae in wood of lower moisture (12%) died faster, both those 20mm under surface (1.5min) and those at 130 mm of depth (10.5min).
Ključne besede: wooden objects, repressive wood protection, microwaves, heating, wood moisture content, house longhorn beetle, Hylotrupes bajulus
Objavljeno v DiRROS: 25.10.2017; Ogledov: 4837; Prenosov: 2845
.pdf Celotno besedilo (1,52 MB)
Gradivo ima več datotek! Več...

3.
Influence of microwave heating in wood preservation on traditional surface coatings
Martin Klinc, Matjaž Pavlič, Marko Petrič, Franc Pohleven, 2017, izvirni znanstveni članek

Povzetek: Microwaves are very effective at wood pest eradication. However, elevated temperatures may pose a risk of damaging surface coatings used on cultural and historical artefacts. Therefore, we monitored changes in patterns of the original paint taken from such objects along with newly prepared coatings. We evaluated visual, mechanical, and chemical modifications of coatings when exposed to microwaves (750W, 2.4GHz), at 60°C or 80°C for 10 min. Whether old or new, only water-based coatings have proven to be resistant to elevated temperatures and no damage was observed at 80°C. Blisters have formed on layers of new oil paints and natural resins due to insufficiently cured film. Temperatures above 80°C may cause melting of coniferous wood resin and thus transport of resin to the surface; on the other hand, temperatures up to 60°C are completely harmless. Mechanical and chemical changes of coatings exposed to microwaves were not observed, but the studies showed that colour and gloss exhibited minor changes.
Ključne besede: wood, wood coatings, wood protection, microwaves, heating
Objavljeno v DiRROS: 03.07.2017; Ogledov: 5657; Prenosov: 3290
.pdf Celotno besedilo (2,63 MB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.11 sek.
Na vrh