Search the repository

A+ | A- | | SLO | ENG

Abstract: Background. Various electrofusion parameters have to be adjusted to obtain theoptimal electrofusion efficiency. Based on published data, good electrofusion conditions can be achieved with the hypotonic treatment. However, the duration of the hypotonic treatment before electroporation and buffer hypoosmolarity have to be adjusted in order to cause cell swelling, to avoid regulatory volume decrease and to preserve cell viability. The aims of our study were to determine cell size dynamics and viability of four different cell lines in hypotonic buffer and to study the influence of the electroporation on the selected cell line in hypotonic buffer. Materials and methods. Cell size dynamics of different cell lines exposed to hypotonic buffer and electroporation were analyzed by time-resolvedcell size measurements. The viability of hypotonically treated oržand electroporated cells was determined 24 h after the experiment by a modified crystal violet (CV) viability assay. Results. In our experimental conditions the hypotonic treatment at 100 mOsm was efficient for CHO, V79 and B16-F1 cell lines. The optimal duration of the treatment was between two and five minutes. On the other hand the same hypotonic treatment did not cause cell swelling of NS1 cells. Cell swelling was also observed after electroporation of B16-F1 in isotonic buffer and it was amplified when hypotonic buffer was used. In addition, the regulatory volume decrease was successfully inhibited with electroporation. Conclusions. Cell size dynamicsin hypotonic conditions should be studied for each cell line since they differ in their sensitivity to the hypotonic treatment. The inhibition of cell regulatory volume decrease by electroporation may be beneficial in achieving higher electrofusion efficiency. (Abstract truncated at 2000 characters)
Keywords: hypotonic treatment, cell swelling, regulatory volume decrease, cell size measurements, viability, electrofusion, electroporation
Published in DiRROS: 08.03.2024; Views: 98; Downloads: 32
Full text (263,01 KB)

Keywords: Al-Ti-B grain-refiners, quality, TiB2 particles, Al3Ti particles, electrical resistance measurements
Published in DiRROS: 01.02.2024; Views: 154; Downloads: 59
Full text (8,93 MB)
This document has many files! More...

Abstract: When creating a simulation model to assess the performance of buildings, there is usually a lack of feedback information. Only in the case of measurements of a real building is a direct comparison of the measured values and simulated results possible. Parameter data related to users’ behavior or other events can also be obtained. Their evaluated frequency, magnitude and duration, along with boundary conditions, are crucial for the results. It is clear that none of them can be predicted very accurately. Most of them, however, are needed for computer modeling. In this paper we analyzed the well-defined TRNSYS simulation model of offices equipped with radiant ceiling panels for heating and cooling. The model was based on real case offices and was validated based on measurements for 1 year. The analysis included simulations in order to define what effect the parameters related mainly to users have on the energy use and the indoor air temperatures. The study confirmed that specific human activities influence the annual energy use to a relatively small degree and that their effects often counteract. It also confirmed the even more important fact that although small, these activities can influence the thermal comfort of users. It is believed that despite the fact that this research was based on an analysis of offices equipped with radiant ceiling panels, most of the results could be applied generally.
Keywords: measurements, modeling, simulation, validation, analysis, energy use, temperature
Published in DiRROS: 15.09.2023; Views: 270; Downloads: 132
Full text (1,83 MB)
This document has many files! More...

Abstract: Secondary Zn–based batteries are a valid alternative to Li for stationary storage, but commercial devices are not yet available, chiefly owing to anode shape-change and passivation issues. Mildly acidic aqueous solutions are actively studied, since they seem to limit unstable growth of Zn, with respect to the alkaline ones, customary for primary batteries. Additives can further improve the performance of mildly acidic electrolytes. In this work we focus on the impact of a series of quaternary ammonium salts (TBAB, CTAB, DMDTDAB, BDMPAC, BPPEI, PDADMAC), selected to represent a comprehensive range of molecular functionalities. Electrochemical measurements (cyclic voltammetry, chronopotentiometry and galvanostatic-cycling in split-cells), combined with 2D and 3D imaging techniques (SEM, stereomicroscopy and in situ tomography) were adopted for the assessment Zn behaviour. This multi-technique approach pinpointed TBAB as the single most effective additive for low-current density operation, while at high current densities the additive-free electrolyte allows better cycling performance, coherently with similar results for alkaline electrolytes.
Keywords: battery, electrolyte, electrochemical measurements, quaternary Ammomium salt, X-ray computed microtomography, mobility
Published in DiRROS: 06.07.2023; Views: 353; Downloads: 154
Full text (2,52 MB)
This document has many files! More...