Iskanje po repozitoriju

A+ | A- | | SLO | ENG

Povzetek: Plant viruses pose a significant threat to agriculture. Several are stable outside their hosts, can enter water bodies and remain infective for prolonged periods of time. Even though the quality of irrigation water is of increasing importance in the context of plant health, the presence of plant viruses in irrigation waters is understudied. In this study, we conducted a large-scale high-throughput sequencing (HTS)-based virome analysis of irrigation and surface water sources to obtain complete information about the abundance and diversity of plant viruses in such waters. We detected nucleic acids of plant viruses from 20 families, discovered several novel plant viruses from economically important taxa, like Tobamovirus and observed the influence of the water source on the present virome. By comparing viromes of water and surrounding plants, we observed presence of plant viruses in both compartments, especially in cases of large-scale outbreaks, such as that of tomato mosaic virus. Moreover, we demonstrated that water virome data can extensively inform us about the distribution and diversity of plant viruses for which only limited information is available from plants. Overall, the results of the study provided extensive insights into the virome of irrigation waters from the perspective of plant health. It also suggested that an HTS-based water virome surveillance system could be used to detect potential plant disease outbreaks and to survey the distribution and diversity of plant viruses in the ecosystem.
Ključne besede: plant viruses, environmental water testing, high-throughput sequencing, agroecosystems, irrigation water, virome
Objavljeno v DiRROS: 29.03.2024; Ogledov: 89; Prenosov: 41
Povezava na datoteko
Gradivo ima več datotek! Več...

Povzetek: Alkali activated materials (AAM) are, in their broadest classification, any binder systems derived by the reaction of an alkali metal source (silicates, alkali hydroxides, carbonates , sulphates) with a solid, amorphous alumosilicate powder (found in precursors such as slag, fly ash and bottom ash). A wide variety of products can be obtained by the alkali activation process and could replace traditional construction products. Among the se, alkali activated foams (AAF) represent one of the most promising materials, owing to their economically accessible alumosilicate rich source materials, including industrial waste materials, clean processing, higher added value and most importantly, pro ducts with competitive properties. In the present study, the properties of alkali activated fly ash - based foam materials were studied at room temperature as well as at elevated temperatures (up to 1200 °C ) in order to develop a durable material in terms o f mechanical properties and suitability for high temperature applications.
Ključne besede: lightweight porous insulating material, alkali activated materials, microstructural analysis
Objavljeno v DiRROS: 05.03.2024; Ogledov: 100; Prenosov: 41
Celotno besedilo (970,74 KB)
Gradivo ima več datotek! Več...

Povzetek: Skorja je večopravilni (večfunkcijski) material, saj deluje kot zaščita (pred fizikalnimi in mehanskimi poškodbami, pa tudi pred biološko razgradnjo), omogoča transport vode in plinov, občasno pomaga pri fotosintezi in nudi podporo drevesu. Skorje je od 10 % do 20 % celotne mase drevesa, vendar je znaten delež ostane neizkoriščen. Da bi prikazali možnosti rabe skorje za izdelavo različnih kompozitov, smo izdelali in analizirali tri različne kompozite, in sicer lesno-plastični kompozit iz skorje in polietilena, trislojni ploščni kompozit iz skorje, zlepljene z melamin-urea-formaldehidnim lepilom, in enoslojni ploščni kompozit iz vlažnih iveri skorje, zlepljenih s taninskimi lepili.
Ključne besede: skorja, iveri, lesno plastični kompozit, iverna plošča
Objavljeno v DiRROS: 29.02.2024; Ogledov: 168; Prenosov: 38
Celotno besedilo (847,20 KB)

Povzetek: Alkali-activated materials are promising materials for the construction industry due to the accessibility of the precursors, which are mainly secondary industrial by-products, and their cost- effective and energy-efficient production. Although these materials are not new, some of the parameters in the technological process are not yet fully understood and tested. Therefore, in this paper in the means of mechanical strength, the preparation of alkali-activated pastes by using a three-roll mill homogenization method is discussed. The influence of homogenization of alkali- activated slurry has been evaluated on different waste materials (fly ash, fly ash with metakaolin, slag mixture (electric arc furnace slag and ladle slag), glass wool, waste green ceramics), which are treated with different alkali activators (NaOH, commercial sodium silicate solution, laboratory-produced alkali activators based on waste cathode- ray tube glass) with different curing regimes (60 °C and 70 °C) and different drying methods (drying at room temperature, drying at 105 °C). The viscosity of the slurry before homogenization was higher than after homogenization, the distribution of elements was more uniform and the compressive strength higher in all homogenized alkali activated materials, regardless of other parameters.
Ključne besede: secondary raw material, alkali activated material, foaming, homogenization, mechanical strength
Objavljeno v DiRROS: 21.12.2023; Ogledov: 224; Prenosov: 73
Celotno besedilo (15,82 MB)
Gradivo ima več datotek! Več...

Povzetek: Alkali activation is studied as a potential technology to produce a group of high performance building materials from industrial residues such as metallurgical slag. Namely, slags containing aluminate and silicate form a useful solid material when activated by an alkaline solution. The alkali-activated (AA) slag-based materials are promising alternative products for civil engineering sector and industrial purposes. In the present study the locally available electric arc furnace steel slag (Slag A) and the ladle furnace basic slag (Slag R) from different metallurgical industries in Slovenia were selected for alkali activation because of promising amorphous Al/Si rich content. Different mixtures of selected precursors were prepared in the Slag A/Slag R ratios 1/0, 3/1, 1/1, 1/3 and 0/1 and further activated with potassium silicate using an activator to slag ratio of 1:2 in order to select the optimal composition with respect to their mechanical properties. Bending strength of investigated samples ranged between 4 and 18 MPa, whereas compressive strength varied between 30 and 60 MPa. The optimal mixture (Slag A/Slag R = 1/1) was further used to study strength development under the influence of different curing temperatures at room temperature (R. T.), and in a heat-chamber at 50, 70 and 90 °C, and the effects of curing time for 1, 3, 7 and 28 days was furthermore studied. The influence of curing time at room temperature on the mechanical strength at an early age was found to be nearly linear. Further, it was shown that specimens cured at 70 °C for 3 days attained almost identical (bending/compressive) strength to those cured at room temperature for 28 days. Additionally, microstructure evaluation of input materials and samples cured under different conditions was performed by means of XRD, FTIR, SEM and mercury intrusion porosimetry (MIP).
Ključne besede: alkali activation, slag, influence of curing regime, FTIR
Objavljeno v DiRROS: 13.09.2023; Ogledov: 243; Prenosov: 133
Celotno besedilo (10,76 MB)
Gradivo ima več datotek! Več...