31. Particle size manipulation as an influential parameter in the development of mechanical properties in electric arc furnace slag-based AAMKatja Traven, Mark Češnovar, Vilma Ducman, 2019, original scientific article Abstract: Alkali-activated materials (AAM) have gained recognition as a promising alternative to technical ceramic and building materials owing to the lower energy demands for production and the potential to use slag as a precursor. In the present study, five sets of slag-based AAM pastes were prepared with different particle sizes (fractions d < 63, 63 < d < 90, and 90 < d < 125 μm in different mass ratios) under the same curing regime and using a fixed precursor to activator (water) mass ratio. Precursors and the hardened AAM are evaluated using BET, XRD, XRF, SEM, FTIR, reactivity of precursors by leaching, and mercury intrusion porosimetry (MIP). Chemical analysis indicated only marginal differences among the different-sized fractions of input materials, whereas the BET surface area and reactivity among the precursors differed significantly-smaller particles had the largest surface area, and thus, higher reactivity. The mineralogical differences between the precursors and hardened AAM were negligible. The results revealed that compressive strength was significantly influenced by particle size, i.e., a threefold increase in strength when the particle size was halved. Microstructural evaluation using MIP confirmed that the porosity was the lowest in AAM with the smallest particle size. The low porosity and high reactivity of the fine fractions led to the highest compressive strength, confirming that manipulation of particle size can significantly influence the mechanical properties.
Keywords: alkalijsko aktivirani materiali, žlindra iz obločne peči, mehanska aktivacija, mehanske lastnosti, poroznost, alkali-activated materials (AAM), electric arc furnace steel slag, mechanical activation, mechanical properties, porosity
Published in DiRROS: 22.11.2023; Views: 247; Downloads: 128
 Full text (2,26 MB)
This document has many files! More... |
32. |
33. RILEM TC 247-DTA round robin test : mix design and reproducibility of compressive strength of alkaliactivated concretesJohn L. Provis, Kamel Arbi, Susana Bernal, Dali Bondar, Anja Buchwald, Arnaud Castel, Sundararaman Chithiraputhiran, Martin Cyr, Alireza Dehghan, Katja Dombrowski-Daube, Ashish Dubey, Vilma Ducman, Gregor J. G. Gluth, Sreejith Nanukuttan, Karl Peterson, Francisca Puertas, Arie van Riessen, Manuel Torres-Carrasco, Guang Ye, Yibing Zuo, 2019, original scientific article Abstract: The aim of RILEM TC 247-DTA Durability Testing of Alkali-Activated Materials is to identify and validate methodologies for testing the durability of alkali-activated concretes. To underpin the durability testing work of this committee, five alkali-activated concrete mixes were developed based on blast furnace slag, fly ash, and flash-calcined metakaolin. The concretes were designed with different intended performance levels, aiming to assess the capability of test methods to discriminate between concretes on this basis. A total of fifteen laboratories worldwide participated in this round robin test programme, where all concretes were produced with the same mix designs, from single-source aluminosilicate precursors and locally available aggregates. This paper reports the mix designs tested, and the compressive strength results obtained, including critical insight into reasons for the observed variability in strength within and between laboratories.
Keywords: alkali-activated materials (AAM), mechanical properties, test method, Rilem TC, durability
Published in DiRROS: 14.09.2023; Views: 228; Downloads: 131
Full text (431,19 KB)
This document has many files! More... |
34. The potential of ladle slag and electric arc furnace slag use in synthesizing alkali activated materials; the influence of curing on mechanical propertiesMark Češnovar, Katja Traven, Barbara Horvat, Vilma Ducman, 2019, original scientific article Abstract: Alkali activation is studied as a potential technology to produce a group of high performance building materials from industrial residues such as metallurgical slag. Namely, slags containing aluminate and silicate form a useful solid material when activated by an alkaline solution. The alkali-activated (AA) slag-based materials are promising alternative products for civil engineering sector and industrial purposes. In the present study the locally available electric arc furnace steel slag (Slag A) and the ladle furnace basic slag (Slag R) from different metallurgical industries in Slovenia were selected for alkali activation because of promising amorphous Al/Si rich content. Different mixtures of selected precursors were prepared in the Slag A/Slag R ratios 1/0, 3/1, 1/1, 1/3 and 0/1 and further activated with potassium silicate using an activator to slag ratio of 1:2 in order to select the optimal composition with respect to their mechanical properties. Bending strength of investigated samples ranged between 4 and 18 MPa, whereas compressive strength varied between 30 and 60 MPa. The optimal mixture (Slag A/Slag R = 1/1) was further used to study strength development under the influence of different curing temperatures at room temperature (R. T.), and in a heat-chamber at 50, 70 and 90 °C, and the effects of curing time for 1, 3, 7 and 28 days was furthermore studied. The influence of curing time at room temperature on the mechanical strength at an early age was found to be nearly linear. Further, it was shown that specimens cured at 70 °C for 3 days attained almost identical (bending/compressive) strength to those cured at room temperature for 28 days. Additionally, microstructure evaluation of input materials and samples cured under different conditions was performed by means of XRD, FTIR, SEM and mercury intrusion porosimetry (MIP).
Keywords: alkali activation, slag, influence of curing regime, FTIR
Published in DiRROS: 13.09.2023; Views: 244; Downloads: 133
Full text (10,76 MB)
This document has many files! More... |
35. Evaluation of locally available amorphous waste materials as a source for alternative alkali activatorsKatja Koenig, Katja Traven, Majda Pavlin, Vilma Ducman, 2021, original scientific article Abstract: The production of alkali-activated materials with excellent mechanical performance requires the use of waterglass, which has a significant carbon footprint. Such materials can have a lower carbon footprint if we replace water glass with alternative activators sourced from waste. In this study, we assessed the suitability of locally available amorphous waste materials (stone wool, glass wool, bottle glass and cathode-ray tube glass) as a source for the preparation of alternative alkali activators. We quantified the amount of silicon and aluminium dissolved in the activator solutions via inductively coupled plasma-optical emission spectrometry. The alternative activators were then used to produce alkali-activated fly ash and slag. The compressive strength values of alkali-activated fly ash specimens upon the addition of NaOH, water glass and the most promising alternative activator were 38.98 MPa, 31.34 MPa and 40.37 MPa, respectively. The compressive strength of slag specimens activated with alternative activators with the highest concentration of dissolved silicon (21 g/L) was, however, 70% higher than the compressive strength of slag specimens activated with only 10 M sodium hydroxide. The compressive strength of slag specimens with the addition of the most promising alternative activator was significantly lower (3.5 MPa) than the compressive strength of those that had been activated by commercial water glass (34.3 MPa).
Keywords: alkalijsko aktivirani materiali, alternativni aktivatorji, lastnosti, alkali activated materials/geopolimers, alternative activators, properties
Published in DiRROS: 22.08.2023; Views: 214; Downloads: 146
Full text (6,02 MB)
This document has many files! More... |
36. RILEM TC 247-DTA round robin test : carbonation and chloride penetration testing of alkali-activated concretesGregor J. G. Gluth, Kamel Arbi, Susana Bernal, Dali Bondar, Arnaud Castel, Sundararaman Chithiraputhiran, Alireza Dehghan, Katja Dombrowski-Daube, Ashish Dubey, Vilma Ducman, Karl Peterson, Penny Pipilikaki, Siska L. A. Valcke, Guang Ye, Yibing Zuo, John L. Provis, 2020, original scientific article Abstract: Many standardised durability testing methods have been developed for Portland cement-based concretes, but require validation to determine whether they are also applicable to alkali-activated materials. To address this question, RILEM TC 247-DTA "Durability Testing of Alkali-Activated Materials" carried out round robin testing of carbonation and chloride penetration test methods, applied to five different alkali-activated concretes based on fly ash, blast furnace slag or metakaolin. The methods appeared overall to demonstrate an intrinsic precision comparable to their precision when applied to conventional concretes. The ranking of test outcomes for pairs of concretes of similar binder chemistry was satisfactory, but rankings were not always reliable when comparing alkali-activated concretes based on different precursors. Accelerated carbonation testing gave similar results for fly ash-based and blast furnace slag-based alkali-activated concretes, whereas natural carbonation testing did not. Carbonation of concrete specimens was observed to have occurred already during curing, which has implications for extrapolation of carbonation testing results to longer service life periods. Accelerated chloride penetration testing according to NT BUILD 443 ranked the tested concretes consistently, while this was not the case for the rapid chloride migration test. Both of these chloride penetration testing methods exhibited comparatively low precision when applied to blast furnace slag-based concretes which are more resistant to chloride ingress than the other materials tested.
Keywords: alkali-activated materials (AAM), carbonatization, chloride penetration, Rilem TC, durability
Published in DiRROS: 17.08.2023; Views: 249; Downloads: 166
Full text (1014,30 KB)
This document has many files! More... |
37. RILEM TC 247-DTA round robin test : sulfate resistance, alkali-silica reaction and freeze-thaw resistance of alkali-activated concretesFrank Winnefeld, Gregor J. G. Gluth, Susana Bernal, Maria Chiara Bignozzi, Lorenza Carabba, Sundararaman Chithiraputhiran, Alireza Dehghan, Sabina Dolenec, Katja Dombrowski-Daube, Ashish Dubey, Vilma Ducman, Yu Jin, Karl Peterson, Stephen Dietmar, John L. Provis, 2020, original scientific article Abstract: The RILEM technical committee TC 247-DTA ‘Durability Testing of Alkali-Activated Materials’ conducted a round robin testing programme to determine the validity of various durability testing methods, originally developed for Portland cement based-concretes, for the assessment of the durability of alkali-activated concretes. The outcomes of the round robin tests evaluating sulfate resistance, alkali-silica reaction (ASR) and freeze–thaw resistance are presented in this contribution. Five different alkali-activated concretes, based on ground granulated blast furnace slag, fly ash, or metakaolin were investigated. The extent of sulfate damage to concretes based on slag or fly ash seems to be limited when exposed to an Na2SO4 solution. The mixture based on metakaolin showed an excessive, very early expansion, followed by a dimensionally stable period, which cannot be explained at present. In the slag-based concretes, MgSO4 caused more expansion and visual damage than Na2SO4; however, the expansion limits defined in the respective standards were not exceeded. Both the ASTM C1293 and RILEM AAR-3.1 test methods for the determination of ASR expansion appear to give essentially reliable identification of expansion caused by highly reactive aggregates. Alkali-activated materials in combination with an unreactive or potentially expansive aggregate were in no case seen to cause larger expansions; only the aggregates of known very high reactivity were seen to be problematic. The results of freeze–thaw testing (with/without deicing salts) of alkali-activated concretes suggest an important influence of the curing conditions and experimental conditions on the test outcomes, which need to be understood before the tests can be reliably applied and interpreted.
Keywords: alkali-activated materials/geopolymers, sulphate resistance, alkali silica reactivity, freeze-thaw resistance, Rilem TC
Published in DiRROS: 17.08.2023; Views: 220; Downloads: 158
Full text (560,56 KB)
This document has many files! More... |
38. High temperature resistant fly-ash and metakaolin-based alkali-activated foamsKatja Traven, Mark Češnovar, Srečo D. Škapin, Vilma Ducman, 2021, original scientific article Abstract: Alkali-activated foams (AAFs) present one of the most promising materials for use in the construction sector. Their main advantages lie in their utilization of waste material and their ability to form at temperatures well below 100 °C, while still competing in performance with foamed glass or ceramics. The present body of research has focused on improving the thermal stability of fly-ash foams by i) adding metakaolin, and ii) changing the activator from sodium-based to potassium-based components. It has been confirmed that a certain increase in thermal resistance is achieved through the addition of metakaolin while changing activators played a crucial role. While sodium-based AAFs without metakaolin start to shrink at approximately 600 °C, samples that have had metakaolin added start to shrink at approximately 700 °C. Samples without metakaolin that have used a potassium activator start to shrink at approximately 800 °C, whereas potassium-based samples with the addition of metakaolin start to shrink at approximately 900 °C.
Keywords: alkali activated materials, geopolymers, high temperature, resistance, foams
Published in DiRROS: 01.08.2023; Views: 247; Downloads: 190
Full text (13,91 MB)
This document has many files! More... |
39. Priporočila za obravnavo bolnikov s pljučnim rakomMartina Vrankar, Nina Boc, Izidor Kern, Aleš Rozman, Karmen Stanič, Tomaž Štupnik, Mojca Unk, Maja Ebert Moltara, Vesna Zadnik, Katja Adamič, Jernej Benedik, Marko Bitenc, Jasna But-Hadžić, Anton Crnjac, Marina Čakš, Dominik Časar, Eva Ćirić, Tanja Čufer, Ana Demšar, Rok Devjak, Goran Gačevski, Marta Globočnik Kukovica, Kristina Gornik-Kramberger, Maja Ivanetič Pantar, Marija Ivanović, Urška Janžič, Staša Jelerčič, Veronika Kloboves-Prevodnik, Mile Kovačević, Luka Ležaič, Mateja Marc-Malovrh, Katja Mohorčič, Loredana Mrak, Igor Požek, Nina Turnšek, Bogdan Vidmar, Dušanka Vidovič, Gregor Vlačić, Ana Lina Vodušek, Rok Zbačnik, Ivana Žagar, 2023, professional article Abstract: Leta 2019 so bila objavljena Priporočila za obravnavo bolnikov s pljučnim rakom, ki so v slovenski prostor vnesla prepotrebno poenotenje diagnostike in zdravljenja z namenom izboljšanja preživetja bolnikov s pljučnim rakom. Posodobitev Priporočil tri leta po izidu izvirnika prinaša največ novosti v poglavju o sistemskem zdravljenju bolnikov s pljučnim rakom. To kaže na izjemen napredek na področju razumevanja onkogeneze in biologije pljučnega raka ter s tem razvoja novih zdravil. Breme pljučnega raka ostaja veliko, saj je pljučni rak pri nas in v svetu še vedno najpogostejši vzrok smrti zaradi raka. Za vsako peto smrt zaradi raka je odgovoren pljučni rak. Skoraj tretjina bolnikov s pljučnim rakom ne prejme specifičnega onkološkega zdravljenja, bodisi zaradi slabega stanja zmogljivosti, spremljajočih bolezni ali obsega bolezni. Polovica bolnikov ima ob diagnozi razsejano bolezen, zaradi česar izboljšanje preživetja z malimi koraki sledi napredku v zdravljenju bolnikov s pljučnim rakom. Ti podatki nas opominjajo, da se bomo morali za velike premike v obravnavi bolnikov s pljučnim rakom lotiti drugačnih pristopov. Kot najbolj obetavno se ponuja zgodnje odkrivanje bolezni, ko so možnosti ozdravitve pljučnega raka najboljše. Zapisana Priporočila so usmeritev za obravnavo bolnikov s pljučnim rakom. Le s sodobnim multidisciplinarnim pristopom obravnave lahko bolniku ponudimo zdravljenje, ki mu omogoča najboljši izhod prognostično neugodne bolezni.
Keywords: pljučni rak, priporočila
Published in DiRROS: 27.07.2023; Views: 379; Downloads: 136
Full text (708,18 KB)
This document has many files! More... |
40. The deformation of alkali-activated materials at an early age under different curing conditionsMark Češnovar, Katja Traven, Vilma Ducman, 2021, original scientific article Abstract: The production of alkali-activated materials (AAMs) is known for its environmentally friendly processing method, where several amorphous-rich aluminosilicate material sources combine with an alkali media solution to form solid, ceramic-like materials. In terms of the Si:Al, Na(K):Al, and Na(K):H2O ratios, the theory of AAM formation is quite well developed, but some open questions in the technology process remain, especially with regards to the means of curing, where the generation of defects can be persistent. Knowing that deformation is extremely high in the early ages, this study investigates the effects of temperature and moisture on shrinkage behavior within the first 72 h of AA pastes made from ladle (LS) and electric arc furnace (EAF) slag and activated by sodium silicate (Na2SiO3). The method to determine the deformation of alkali-activated slag-based materials, in terms of both autogenous and drying shrinkage, was based on the modified ASTM C1698-19 standard for the measurement of autogenous shrinkage in cement pastes. Autogenous deformation and strain were measured in four samples, using the standard procedure at room temperature, 40 and 60°C. Furthermore, using an adjusted method, nine samples were characterized for strain and partial surface pressure, while drying at room temperature, 40, or 60°C at a relative humidity of 30 or 90%. The results show that the highest rate of autogenous shrinkage occurred at a temperature of 60°C, followed by drying shrinkage at 60°C and 30% relative humidity, owing to the fact that the rate of evaporation was highest at this moisture content. The study aimed to provide guidance regarding selection of the optimal curing set in order to minimize deformations in slag-based alkali-activated materials. In the present case, curing at a temperature of around 40°C under lower moisture conditions for the first 24 h provided optimal mechanical properties for the slags investigated. The methodology might also be of use for other aluminosilicate sources such as metakaolin, fly ash, and mineral wool–based alkali-activated materials.
Keywords: alkali-activated materials, slag, drying, autogenous shrinkage, partial surface pressure, curing deformation
Published in DiRROS: 03.07.2023; Views: 370; Downloads: 132
Full text (2,23 MB)
This document has many files! More... |
