Digitalni repozitorij raziskovalnih organizacij Slovenije

Iskanje po repozitoriju
A+ | A- | Pomoč | SLO | ENG

Iskalni niz: išči po
išči po
išči po
išči po

Možnosti:
  Ponastavi


Iskalni niz: "ključne besede" (foaming) .

1 - 3 / 3
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Fibre reinforced alkali-activated rock wool
Majda Pavlin, Barbara Horvat, Vilma Ducman, 2022, objavljeni znanstveni prispevek na konferenci

Povzetek: Mineral wool, i.e. rock and glass wool, represents considerable challenge after its functional-time runs out due to its small density leading to large volume consumption during transport and in landfills where it usually ends. Because rock wool is mineralogically and chemically a promising precursor material for alkali-activation, it was milled from few centimetres-decimeters long fibres to micron-sized fibres. Since fibres in alkali-activated materials generally show an increase in mechanical strength, especially the bending strength, 1 m% of additional fibres (basalt, cellulose (2 types), glass, polypropylene, polyvinyl alcohol and steel fibres) was used in the alkali mixture, that was curred at 40 °C for 3 days. Time dependence of the mechanical strengths of alkali- activated materials with and without additional fibres was followed. Maximal increase of compressive and bending strength after 28 days was reached with polypropylene fibres, i.e. it was 20% and 30% higher than compressive and bending strength of alkali- activated material without additional fibres respectively.
Ključne besede: secondary raw material, alkali activated material, foaming, homogenization, mechanical strength
Objavljeno v DiRROS: 21.12.2023; Ogledov: 620; Prenosov: 258
.pdf Celotno besedilo (8,39 MB)
Gradivo ima več datotek! Več...

2.
Influence of homogenization of alkali-activated slurry on mechanical strength
Barbara Horvat, Mark Češnovar, Katja Traven, Majda Pavlin, Katja Koenig, Vilma Ducman, 2022, objavljeni znanstveni prispevek na konferenci

Povzetek: Alkali-activated materials are promising materials for the construction industry due to the accessibility of the precursors, which are mainly secondary industrial by-products, and their cost- effective and energy-efficient production. Although these materials are not new, some of the parameters in the technological process are not yet fully understood and tested. Therefore, in this paper in the means of mechanical strength, the preparation of alkali-activated pastes by using a three-roll mill homogenization method is discussed. The influence of homogenization of alkali- activated slurry has been evaluated on different waste materials (fly ash, fly ash with metakaolin, slag mixture (electric arc furnace slag and ladle slag), glass wool, waste green ceramics), which are treated with different alkali activators (NaOH, commercial sodium silicate solution, laboratory-produced alkali activators based on waste cathode- ray tube glass) with different curing regimes (60 °C and 70 °C) and different drying methods (drying at room temperature, drying at 105 °C). The viscosity of the slurry before homogenization was higher than after homogenization, the distribution of elements was more uniform and the compressive strength higher in all homogenized alkali activated materials, regardless of other parameters.
Ključne besede: secondary raw material, alkali activated material, foaming, homogenization, mechanical strength
Objavljeno v DiRROS: 21.12.2023; Ogledov: 590; Prenosov: 250
.pdf Celotno besedilo (15,82 MB)
Gradivo ima več datotek! Več...

3.
Potential of green ceramics waste for alkali activated foams
Barbara Horvat, Vilma Ducman, 2019, izvirni znanstveni članek

Povzetek: The aim of the paper is to research the influence of foaming and stabilization agents in the alkali activation process of waste green ceramics for future low cost up-cycling into lightweight porous thermal insulating material. Green waste ceramics, which is used in the present article, is a green body residue (non-successful intermediate-product) in the synthesis of technical ceramics for fuses. This residue was alkali activated with Na-water glass and NaOH in theoretically determined ratio based on data from X-ray fluorescence (XRF) and X-ray powder diffraction (XRD) that was set to maximise mechanical properties and to avoid efflorescence. Prepared mixtures were compared to alkali activated material prepared in theoretically less favourable ratios, and tested on the strength and density. Selected mixtures were further foamed with different foaming agents, that are Na-perborate (s), H2O2 (l), and Al (s), and supported by a stabilization agent, i.e., Na-dodecyl sulphate. The goal of the presented work was to prepare alkali activated foam based on green ceramics with density below 1 kg/l and compressive strength above 1 MPa.
Ključne besede: alkali activation, foaming, SEM, XRF, XRD, mechanical strength
Objavljeno v DiRROS: 14.09.2023; Ogledov: 675; Prenosov: 331
.pdf Celotno besedilo (6,88 MB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.1 sek.
Na vrh