Digitalni repozitorij raziskovalnih organizacij Slovenije

Iskanje po repozitoriju
A+ | A- | Pomoč | SLO | ENG

Iskalni niz: išči po
išči po
išči po
išči po

Možnosti:
  Ponastavi


Iskalni niz: "avtor" (Mirja Illikainen) .

1 - 3 / 3
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Analysis of alkali-activated mineral wool-slag binders : evaluating the differences between one-part and two-part variations
Elijah Adesanya, Rawia Dabbebi, Christine Rößler, Majda Pavlin, Zhenming Li, Tero Luukkonen, Juho Yliniemi, Mirja Illikainen, 2024, izvirni znanstveni članek

Povzetek: Two synthesis pathways (one- and two-part) in alkali-activated binders were compared using ground granulated blast furnace slag (GGBFS), mineral wool (MW) activated using dry and liquid alkali activators with similar Na2O/SiO2 modulus. The effect of activator type on reaction kinetics, strength development, setting times, and durability shows that one-part synthesis does not only improve early strength, but also provide better durability properties. While the highest compressive strength (56 MPa, 90 days) was achieved for the one-part mix (DM), the reaction products (presence of Mg–Al layered double hydroxide and C–S–H-like phases) observed for both mortar mixes were similar. The DM mortars showed better resistance to sulfate attack than two-part mix (WM) mortars and sets faster. The results highlight the significance of the one-part pathways in the synthesis of alkali-activated materials.
Ključne besede: recycling, alkali activated material, mineral wool
Objavljeno v DiRROS: 11.03.2024; Ogledov: 454; Prenosov: 369
.pdf Celotno besedilo (1,28 MB)
Gradivo ima več datotek! Več...

2.
Production of lightweight alkali activated mortars using mineral wools
Ahmad Alzaza, Mohammad Mastali, Paivo Kinnunen, Lidija Korat, Zahra Abdollahnejad, Vilma Ducman, Mirja Illikainen, 2019, izvirni znanstveni članek

Povzetek: This experimental study aimed to develop a fiber-reinforced lightweight mineral wool-based alkali activated mortar. The lightweight mineral wool-based alkali activated mortars were produced using premade foam and reinforced by polypropylene (PP) fibers. They were assessed in terms of fresh and hardened-state properties. Fresh-state properties were investigated by mini-slump tests. Hardened-state characteristics were assessed by ultrasonic pulse velocity, dry density, compressive and flexural strengths, drying shrinkage, efflorescence, water absorption, and permeable porosity. For the first time, the resistance of the synthesized lightweight mineral wool-based alkali activated mortars against harsh conditions (carbonation, freeze and thaw, and high temperature) were evaluated. The porous structures of the developed lightweight alkali activated mortars were also analyzed using an X-ray micro-computed tomography (CT) technique. Lightweight mix compositions with densities in a range of 770%1510 kg/m3, compressive strengths of 1%9 MPa, and flexural strengths of 2.6%8 MPa were developed. Increases in both density and strength after carbonation were also recorded, while a decrease of strength was noticed after exposure to freeze/thaw and high temperatures of up to 500 %C.
Ključne besede: alkali activation, mineral wool, mortars
Objavljeno v DiRROS: 24.10.2023; Ogledov: 612; Prenosov: 278
.pdf Celotno besedilo (10,47 MB)
Gradivo ima več datotek! Več...

3.
Impacts of casting scales and harsh conditions on the thermal, acoustic, and mechanical properties of indoor acoustic panels made with fiber-reinforced alkali-activated slag foam concretes
Mohammad Mastali, Paivo Kinnunen, Marjaana Karhu, Zahra Abdollahnejad, Lidija Korat, Vilma Ducman, Ahmad Alzaza, Mirja Illikainen, 2019, izvirni znanstveni članek

Povzetek: This paper presents experimental results regarding the efficiency of using acoustic panels made with fiber-reinforced alkali-activated slag foam concrete containing lightweight recycled aggregates produced by using Petrit-T (tunnel kiln slag). In the first stage, 72 acoustic panels with dimension 500 % 500 % 35 mm were cast and prepared. The mechanical properties of the panels were then assessed in terms of their compressive and flexural strengths. Moreover, the durability properties of acoustic panels were studied using harsh conditions (freeze/thaw and carbonation tests). The efficiency of the lightweight panels was also assessed in terms of thermal properties. In the second stage, 50 acoustic panels were used to cover the floor area in a reverberation room. The acoustic absorption in diffuse field conditions was measured, and the interrupted random noise source method was used to record the sound pressure decay rate over time. Moreover, the acoustic properties of the panels were separately assessed by impedance tubes and airflow resistivity measurements. The recorded results from these two sound absorption evaluations were compared. Additionally, a comparative study was presented on the results of impedance tube measurements to compare the influence of casting volumes (large and small scales) on the sound absorption of the acoustic panels. In the last stage, a comparative study was implemented to clarify the effects of harsh conditions on the sound absorption of the acoustic panels. The results showed that casting scale had great impacts on the mechanical and physical properties. Additionally, it was revealed that harsh conditions improved the sound properties of acoustic panels due to their effects on the porous structure of materials.
Ključne besede: alkali activation, slag, acoustic panels
Objavljeno v DiRROS: 15.09.2023; Ogledov: 560; Prenosov: 286
.pdf Celotno besedilo (10,70 MB)
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.08 sek.
Na vrh