Digitalni repozitorij raziskovalnih organizacij Slovenije

Iskanje po repozitoriju
A+ | A- | Pomoč | SLO | ENG

Iskalni niz: išči po
išči po
išči po
išči po

Možnosti:
  Ponastavi


Iskalni niz: "avtor" (Martin Cyr) .

1 - 2 / 2
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
RILEM TC 247-DTA round robin test : mix design and reproducibility of compressive strength of alkaliactivated concretes
John L. Provis, Kamel Arbi, Susan A. Bernal, Dali Bondar, Anja Buchwald, Arnaud Castel, Sundararaman Chithiraputhiran, Martin Cyr, Alireza Dehghan, Katja Dombrowski-Daube, Ashish Dubey, Vilma Ducman, Gregor J. G. Gluth, Sreejith Nanukuttan, Karl Peterson, Francisca Puertas, Arie van Riessen, Manuel Torres-Carrasco, Guang Ye, Yibing Zuo, 2019, izvirni znanstveni članek

Povzetek: The aim of RILEM TC 247-DTA Durability Testing of Alkali-Activated Materials is to identify and validate methodologies for testing the durability of alkali-activated concretes. To underpin the durability testing work of this committee, five alkali-activated concrete mixes were developed based on blast furnace slag, fly ash, and flash-calcined metakaolin. The concretes were designed with different intended performance levels, aiming to assess the capability of test methods to discriminate between concretes on this basis. A total of fifteen laboratories worldwide participated in this round robin test programme, where all concretes were produced with the same mix designs, from single-source aluminosilicate precursors and locally available aggregates. This paper reports the mix designs tested, and the compressive strength results obtained, including critical insight into reasons for the observed variability in strength within and between laboratories.
Ključne besede: alkali-activated materials (AAM), mechanical properties, test method, Rilem TC, durability
Objavljeno v DiRROS: 14.09.2023; Ogledov: 397; Prenosov: 216
.pdf Celotno besedilo (431,19 KB)
Gradivo ima več datotek! Več...

2.
Application of electrochemical methods for studying steel corrosion in alkali-activated materials
Shishir Mundra, Gabriel Samson, Giulia Masi, Rebecca Achenbach, David M. Bastidas, Susan A. Bernal, Maria Chiara Bignozzi, Maria Criado, Martin Cyr, Nina Gartner, Stefanie von Greve‐Dierfeld, Andraž Legat, Nikoonasab Ali, John L. Provis, Michael Raupach, Gregor J. G. Gluth, 2023, izvirni znanstveni članek

Povzetek: Alkali‐activated materials (AAMs) are binders that can complement and partially substitute the current use of conventional cement. However, the present knowledge about how AAMs protect steel reinforcement in concrete elements is incomplete, and uncertainties exist regarding the application of electrochemical methods to investigate this issue. The present review by EFC WP11‐Task Force ‘Corrosion of steel in alkali‐activated materials’ demonstrates that important differences exist between AAMs and Portland cement, and between different classes of AAMs, which are mainly caused by differing pore solution compositions, and which affect the outcomes of electrochemical measurements. The high sulfide concentrations in blast furnace slag‐based AAMs lead to distinct anodic polarisation curves, unusually low open circuit potentials, and low polarisation resistances, which might be incorrectly interpreted as indicating active corrosion of steel reinforcement. No systematic study of the influence of the steel–concrete interface on the susceptibility of steel to corrosion in AAMs is available. Less common electrochemical methods present an opportunity for future progress in the field.
Ključne besede: alkali-aktivated materials, alkali‐activated materials, anodic/cathodic polarisation, concrete, linear polarisation resistance, open circuit potential, reinforcement corrosion, resistivity
Objavljeno v DiRROS: 29.05.2023; Ogledov: 432; Prenosov: 218
URL Povezava na datoteko
Gradivo ima več datotek! Več...

Iskanje izvedeno v 0.98 sek.
Na vrh