1. Bioresorbability dependence on microstructure of additivelly- manufactured and conventionally-produced Fe-Mn alloysMatjaž Godec, Jakob Kraner, Danijela Anica Skobir Balantič, Irena Paulin, Damjana Drobne, Veno Kononenko, Aleksandra Kocijan, Paul J. McGuiness, Črtomir Donik, 2024, zaključena znanstvena zbirka raziskovalnih podatkov Povzetek: The dataset supports the results shown in the tables and figures in the article entitled “Bioresorbability Dependence on Microstructure of Additivelly-Manufactured and Conventionally-Produced Fe-Mn Alloys” (doi.org/10.1016/j.jmrt.2024.04.097). It contains measurements of corrosion resistance of Fe-Mn samples, phase analysis of samples A, B and C, surface and depth profiling XPS, EDS measurements of a cross-section of Fe-Mn powder particles and viability measurements results.
Ključne besede: Fe-Mn alloy, laser powder bed fusion, bioresorbable, microstructure, corrosion behaviour, biocompatibility
Objavljeno v DiRROS: 12.04.2024; Ogledov: 150; Prenosov: 57
 Celotno besedilo (2,55 MB)
Gradivo ima več datotek! Več... |
2. |
3. |
4. The effect of heat treatment on the interface of 155 PH martensitic stainless steel and SAF 2507 duplex steel in functionally graded AM componentsMartina Koukolíková, Pavel Podaný, Sylwia Rzepa, Michal Brázda, Aleksandra Kocijan, 2023, izvirni znanstveni članek Povzetek: Multi-material components, also known as functionally graded materials (FGMs), are innovative materials that possess unique properties due to their composition and have many potential applications in engineering and science. The effect of the heat treatment (HT) of functionally graded materials 15–5 precipitation-hardened (PH) martensitic steel and SAF 2507 duplex stainless steel (and the opposite order of deposition, i.e. SAF 2507 first followed by 15–5 PH stainless steel) on the interface microstructures was systematically investigated in the presented research. The choice of HT followed the trend of optimum post-processing for the individual alloys. A significant modification in the interface microstructure, characterized in the microstructural transition zone (MTZ) formed above the fusion line. Mechanical properties by miniaturized testing method including hardness measurement characterized both types of interfaces. The sequence of the materials’ application did not have a significant effect on their final mechanical tensile properties in the heat-treated states. Nevertheless, the microstructural change at the MTZ led to drop in the hardness at the interface. The research presents heat-treated FGMs in a horizontal configuration to form a high-quality metallurgical joint between heterogeneous materials manufactured by powder-based directed energy deposition method.
Ključne besede: heat treatment, additive manufacturing, martensitic stainless steel, duplex steel, microstructure, mechanical properties
Objavljeno v DiRROS: 04.04.2024; Ogledov: 56; Prenosov: 12
 Povezava na datoteko |
5. Additive manufacturing multi-material components of SAF 2507 duplex steel and 15-5 PH martensitic stainless steelMartina Koukolíková, Pavel Podaný, Sylwia Rzepa, Michal Brázda, Aleksandra Kocijan, 2023, izvirni znanstveni članek Povzetek: The study reports the successful deposition of 15–5 precipitation-hardened (PH) martensitic steel on SAF 2507 duplex stainless steel (and vice versa) to form functionally graded materials (FGMs) using powder-based, directed-energy-deposition (DED) technology. The evolution of the microstructure and the mechanical properties of the 15–5 PH/SAF 2507 functionally graded material in the as-built state were investigated systematically. The results proved that the microstructural transition zone (MTZ) is formed above the fusion line due to the dilution effect of both steels. The phase composition of the MTZ consists of ferrite and, in comparison to the base materials, an increased amount of austenite. The interface has the lowest hardness owing to the formation of a significant proportion of the austenitic phase. However, the tensile mechanical properties were not affected by the interface as failure occurred in both SAF 2507 and at the interface regions. The research presents a promising application of FGMs in a horizontal configuration to form a high - quality, metallurgical joint between heterogeneous materials. This study introduces a novel approach by additive manufacturing (AM) of heterogeneous multi-materials, merging the favorable properties of duplex SAF 2507 and martensitic 15-5 PH stainless steels through superior metallurgical bonding. The combination of SAF 2507 and 15-5 PH in a functionally graded material has not been previously explored, as the existing studies deal with the duplex stainless steels SAF 2507 and either martensitic stainless-steel 15-5 PH deposited separately by laser powder-bed-fusion (L-PBF) or DED methods. This research pioneers the investigation of these materials in tandem, paving the way for the development of novel FGMs with optimized properties for specific applications. The resulting FGM exhibits exceptional corrosion resistance and high strength, making it highly versatile for applications in diverse industries such as offshore oil and gas production, aerospace, aviation, and chemical processing equipment.
Ključne besede: directed energy deposition, functionally graded materials, miniaturized specimen testing methods, SAF 2507, 15-5 PH
Objavljeno v DiRROS: 04.04.2024; Ogledov: 60; Prenosov: 28
Povezava na datoteko |
6. |
7. |
8. |
9. Effect of post-treated low-temperature plasma nitriding on the wear and corrosion resistance of 316L stainless steel manufactured by laser powder-bed fusionMatjaž Godec, Črtomir Donik, Aleksandra Kocijan, Bojan Podgornik, Danijela Anica Skobir Balantič, 2020, izvirni znanstveni članek Ključne besede: austenitic stainless steel, powder bed fusion, low-temperature plasma nitriding, wear and corrosion behaviour, dislocation cell structure
Objavljeno v DiRROS: 25.03.2024; Ogledov: 94; Prenosov: 61
 Celotno besedilo (3,28 MB)
Gradivo ima več datotek! Več... |
10. Use of plasma nitriding to improve the wear and corrosion resistance of 18Ni-300 maraging steel manufactured by selective laser meltingMatjaž Godec, Bojan Podgornik, Aleksandra Kocijan, Črtomir Donik, Danijela Anica Skobir Balantič, 2021, izvirni znanstveni članek Ključne besede: selective laser melting, 18Ni-300 maraging steel, heat treatment, plasma nitriding, retained and reverted austenite, wear and corrosion behaviour
Objavljeno v DiRROS: 25.03.2024; Ogledov: 103; Prenosov: 56
Celotno besedilo (3,37 MB)
Gradivo ima več datotek! Več... |
