1. Bioresorbability dependence on microstructure of additivelly- manufactured and conventionally-produced Fe-Mn alloysMatjaž Godec, Jakob Kraner, Danijela Anica Skobir Balantič, Irena Paulin, Damjana Drobne, Veno Kononenko, Aleksandra Kocijan, Paul J. McGuiness, Črtomir Donik, 2024, zaključena znanstvena zbirka raziskovalnih podatkov Povzetek: The dataset supports the results shown in the tables and figures in the article entitled “Bioresorbability Dependence on Microstructure of Additivelly-Manufactured and Conventionally-Produced Fe-Mn Alloys” (doi.org/10.1016/j.jmrt.2024.04.097). It contains measurements of corrosion resistance of Fe-Mn samples, phase analysis of samples A, B and C, surface and depth profiling XPS, EDS measurements of a cross-section of Fe-Mn powder particles and viability measurements results.
Ključne besede: Fe-Mn alloy, laser powder bed fusion, bioresorbable, microstructure, corrosion behaviour, biocompatibility
Objavljeno v DiRROS: 12.04.2024; Ogledov: 150; Prenosov: 57
 Celotno besedilo (2,55 MB)
Gradivo ima več datotek! Več... |
2. Effect of post-treated low-temperature plasma nitriding on the wear and corrosion resistance of 316L stainless steel manufactured by laser powder-bed fusionMatjaž Godec, Črtomir Donik, Aleksandra Kocijan, Bojan Podgornik, Danijela Anica Skobir Balantič, 2020, izvirni znanstveni članek Ključne besede: austenitic stainless steel, powder bed fusion, low-temperature plasma nitriding, wear and corrosion behaviour, dislocation cell structure
Objavljeno v DiRROS: 25.03.2024; Ogledov: 94; Prenosov: 61
 Celotno besedilo (3,28 MB)
Gradivo ima več datotek! Več... |
3. Use of plasma nitriding to improve the wear and corrosion resistance of 18Ni-300 maraging steel manufactured by selective laser meltingMatjaž Godec, Bojan Podgornik, Aleksandra Kocijan, Črtomir Donik, Danijela Anica Skobir Balantič, 2021, izvirni znanstveni članek Ključne besede: selective laser melting, 18Ni-300 maraging steel, heat treatment, plasma nitriding, retained and reverted austenite, wear and corrosion behaviour
Objavljeno v DiRROS: 25.03.2024; Ogledov: 103; Prenosov: 56
Celotno besedilo (3,37 MB)
Gradivo ima več datotek! Več... |
4. Improving the surface properties of additive-manufactured Inconel 625 by plasma nitridingDanijela Anica Skobir Balantič, Črtomir Donik, Bojan Podgornik, Aleksandra Kocijan, Matjaž Godec, 2023, izvirni znanstveni članek Povzetek: As a surface-hardening technique, plasma nitriding is a common procedure for improving the properties of
conventional Ni-based alloys. The diffusion of nitrogen hardens a layer on the surface of the alloy, leading to
better wear resistance and a higher coefficient of friction, as well as a higher surface hardness. This study reports
the effect of plasma nitriding on additive-manufactured (AM) Inconel 625 (IN625) compared to its conventional
manufactured and nitrided counterparts. The samples produced with the laser powder-bed fusion (LPBF) process
were subsequently plasma nitrided in the as-built condition, stress-relief annealed at 870 °C and solution treated
at 1050 °C. The plasma nitridings were carried out at 430 °C and 500 °C for 15 h. The growth kinetics of the
nitride layer of the AM samples depends on the prior heat treatments and is faster in the as-built state due to the
specific cellular structure. The lower nitriding temperature leads to the formation of expanded austenite in the
nitride layer, while at the higher nitriding temperature, the expanded austenite decomposes and CrN precipitation
occurs. The XRD and SEM analyses confirmed the presence of two layers: the surface layer and the
diffusion layer beneath. The lower nitriding temperature caused the formation of expanded austenite or a
combination of expanded austenite and CrN. The higher nitriding temperature led to the decomposition of the
expanded austenite and to the formation/precipitation of CrN. The higher nitriding temperature also decreased
the corrosion resistance slightly due to the increased number of precipitated Cr-nitrides. On the other hand, the
wear resistance was significantly improved after plasma nitriding and was much less influenced by the nitriding
temperature.
Ključne besede: additive manufacturing, powder-bed fusion, plasma nitriding, expanded austenite, wear and corrosion resistance, Ni-based alloy
Objavljeno v DiRROS: 31.01.2024; Ogledov: 178; Prenosov: 76
Celotno besedilo (7,98 MB)
Gradivo ima več datotek! Več... |
5. The influence of the plasma-nitriding temperature on the microstructure evolution and surface properties of additive-manufactured 18Ni300 maraging steelMatjaž Godec, Francisco Ruiz-Zepeda, Bojan Podgornik, Črtomir Donik, Aleksandra Kocijan, Danijela Anica Skobir Balantič, 2022, izvirni znanstveni članek Ključne besede: maraging steel, powder bed fusion, plasma nitriding, microstructure, wear resistance, corrosion resistance
Objavljeno v DiRROS: 06.05.2022; Ogledov: 582; Prenosov: 198
Celotno besedilo (6,68 MB)
Gradivo ima več datotek! Več... |
