1. Functional biocarbon-based coatings for wood protection and indoor air depollutionMariem Zouari, Laetitia Sarah Jennifer Marrot, David Brian DeVallance, 2024, original scientific article Abstract: Growing concerns about indoor air pollution heighten the need to develop depolluting materials to achieve a healthy built environment. This study developed functional coatings for wooden surfaces using 20 wt% photocatalytic biocarbon particles doped with manganese oxide (BC–MnO2) and two different coating materials (linseed oil and waterborne acrylic). The samples' surface hydrophobicity and color properties were tested before and after accelerated aging. The depolluting potential of the samples was evaluated by formaldehyde removal efficiency test in indoor conditions. Results showed that adding BC-MnO2 particles increased the hydrophobicity regardless of the coating material's type. After accelerated aging, the hydrophobicity of all samples increased, which was attributed to the curing of the oil and acrylic polymers and the increase in surface roughness eventually caused by surface damage. The color change (ΔE) was more intense in the case of uncoated wood and samples without BC-MnO2. However, the BC-MnO2-containing coatings were effective in color preservation (ΔE < 2), which was attributed to the anti-UV property of biocarbon. The BC-MnO2-containing coatings exhibited a promising formaldehyde removal efficiency of up to 24 % and 46 % for oil and acrylic samples, respectively. The combination of BC-MnO2 and acrylic material was more favourable to attracting the formaldehyde molecules, likely due to the similar polarity. The developed functional coatings exhibited an acceptable ability for wood protection and formaldehyde remediation and can be potentially used to enhance indoor air quality. Keywords: photocatalytic wood coating, hydrophobic surface, UV protection, volatile organic compound, formaldehyde removal Published in DiRROS: 30.01.2025; Views: 112; Downloads: 100
Full text (2,09 MB) This document has many files! More... |
2. Crack size in coating and moisture problems comparing thermally modified and native spruce window frame profiles using hygrothermal simulationGregor Vidmar, Rožle Repič, Boštjan Lesar, Miha Humar, 2024, original scientific article Abstract: Fungal growth and degradation of wood may be caused by damage in the surface coating. The larger the cracks, the greater in principle the possibility of moisture-induced problems. Measuring basic unknown material parameters and employing hygrothermal simulations, the suitability and the maximum acceptable vertical crack size in the surface coating for a given bottom window profile made of thermally modified (TM) spruce(wood) with that made of native spruce were compared for location Ljubljana. Validation with the field test data was the second objective of the respective research. The average calculated maximum moisture content in TM spruce is about 4% (kg/kg) lower than that of native spruce. The 3 mm wide crack in the surface coating of a window frame made of native spruce is of the highest concern, whereas a 9 mm wide crack in the coating of a TM spruce profile is still acceptable. As far as moisture content is concerned in our study the TM spruce window frames were proved to be significantly more suitable for installation than the corresponding frames made of native Norway spruce. It was shown that isopleth, VTT and biohygrothermal models for mould growth do not properly capture the comparison between both materials, mainly because they classify both in the same material class/substrate category and they do not consider the material moisture content. Keywords: hygrothermal simulations, mould growth modelling, cracks in surface coating, thermally modified wood, wooden window frame Published in DiRROS: 16.10.2024; Views: 345; Downloads: 426
Full text (1,48 MB) This document has many files! More... |
3. Influence of drying temperature on properties of wood surfacesMilan Šernek, 2002, original scientific article Abstract: This article deals with modifications of wood surface properties induced by different drying temperatures. The aim of the study was chemical and physical characterization of a wood surface concerning low and high temperature exposure. Additionally, the correlation between the chemical composition of a wood surface and its wetting capacity were investigated. X-ray photoelectron spectroscopy and contact angle measurements were conducted. Two wood species, yellow poplar (Liriodendron tulipifera) and southern pine (Pinus taeda) were studied. The results showed that the percentage of carbon increased with drying temperature, and consequently, the percentage of oxygen decreased. The samples exposed to high drying temperatures indicated a higher content of extractives on the wood surface. These samples exhibited the highest contact angle and the lowest wettability Keywords: površina lesa, sušenje, kontaktni kot, rentgenska fotoelektronska spektroskopija, omočitev, ekstraktivne snovi, wood surface, drying, contact angle, XPS, wettability, extractives Published in DiRROS: 12.07.2017; Views: 5118; Downloads: 2119
Full text (932,44 KB) |